uudecode(1) User Commands uudecode(1)NAMEuudecode - decode an encoded file
SYNOPSISuudecode [-flag [value]]... [--opt-name[[=| ]value]]... [<file>...]
If no file(s) are provided, then standard input is decoded.
DESCRIPTIONuudecode transforms uuencoded files into their original form. The
encoded file(s) may be specified on the command line, or one may be
read from standard input. The output file name is specified in the
encoded file, but may be overridden with the -o option. It will have
the mode of the original file, except that setuid and execute bits are
not retained. If the output file is specified to be /dev/stdout or -,
the result will be written to standard output. If there are multiple
input files and the second or subsquent file specifies standard output,
the decoded data will be written to the same file as the previous out‐
put. Don't do that. uudecode ignores any leading and trailing lines.
It looks for a line that starts with "begin" and proceeds until the
end-of-encoding marker is found. The program determines from the
header line of the encoded file which of the two supported encoding
schemes was used and whether or not the output file name has been
encoded with base64 encoding. See uuencode(5).
OPTIONS-o file, --output-file=file
direct output to file.
If specifed, decoded data are written to this file. When multi‐
ple inputs are specified on the command line, this option cannot
be specified. All decoded data must be written to the file name
encoded in the data.
-c, --ignore-chmod
ignore fchmod(3P) errors.
By default, if the output file permissions cannot be changed to
the permissions specified in the encoded data, the file will not
be written out and execution stops. This option will cause that
error to be ignored. The resulting file will have all the data,
but the incorrect mode settings.
fchmod() errors are also ignored if POSIXLY_CORRECT is set in
the environment. RE: http://austingroupbugs.net/view.php?id=635
A warning is always emitted when fchmod() fails.
-h, --help
Display usage information and exit.
-!, --more-help
Pass the extended usage information through a pager.
-R [rcfile], --save-opts[=rcfile]
Save the option state to rcfile. The default is the last con‐
figuration file listed in the OPTION PRESETS section, below.
The command will exit after updating the config file.
-r rcfile, --load-opts=rcfile, --no-load-opts
Load options from rcfile. The no-load-opts form will disable
the loading of earlier RC/INI files. --no-load-opts is handled
early, out of order.
-v [{v|c|n}], --version[={v|c|n}]
Output version of program and exit. The default mode is `v', a
simple version. The `c' mode will print copyright information
and `n' will print the full copyright notice.
OPTION PRESETS
Any option that is not marked as not presettable may be preset by load‐
ing values from configuration ("RC" or ".INI") file(s). The file
"$HOME/.sharrc" will be used, if present.
STANDARDS
This implementation is compliant with P1003.2b/D11.
FILES
See OPTION PRESETS for configuration files.
EXIT STATUS
One of the following exit values will be returned:
0 (EXIT_SUCCESS)
Successful program execution.
1 (EXIT_OPTION_ERROR)
The command options were misconfigured.
2 (EXIT_INVALID)
(warning) One or more input files contained no valid data
4 (EXIT_NO_INPUT)
(warning) The specified input file was not found
8 (EXIT_NO_OUTPUT)
The specified output file could not be created (error); or else
one of the output files could not be written or its access mode
could not be changed (warnings). The accompanying message(s)
will distinguish.
9 (EXIT_NO_MEM)
No process memory available
66 (EX_NOINPUT)
A specified configuration file could not be loaded.
70 (EX_SOFTWARE)
libopts had an internal operational error. Please report it to
autogen-users@lists.sourceforge.net. Thank you.
The exit status codes are (mostly) warning codes. As such, each code
is "or"-ed into the final exit code as the input files are processed.
For example, an exit code of '6' is not listed above. It is the sum of
EXIT_INVALID and EXIT_NO_INPUT. It would mean that at least one input
file contained invalid data and also at least one input file could not
be found at all.
SEE ALSOuuencode(1), uuencode(5)AUTHORS
Free Software Foundation, Inc.
COPYRIGHT
Copyright (C) 1994-2013 Free Software Foundation, Inc. all rights
reserved. This program is released under the terms of the GNU General
Public License, version 3 or later.
BUGS
Please put sharutils in the subject line for emailed bug reports. It
helps to spot the message.
If more than one name in the encoded files are the same, or if the sec‐
ond or following input files specifies standard output for the output
file, then the result is probably not what is expected. Specifically,
standard output will be appended to and named output files will be
replaced.
Please send bug reports to: bug-gnu-utils@gnu.org
NOTES
This manual page was AutoGen-erated from the uudecode option defini‐
tions.
GNU sharutils (4.13.5) 12 Apr 2013 uudecode(1)
