sane-dc210 man page on Syllable

Man page or keyword search:  
man Server   2339 pages
apropos Keyword Search (all sections)
Output format
Syllable logo
[printable version]

sane-dc210(5)		 SANE Scanner Access Now Easy		 sane-dc210(5)

NAME
       sane-dc210 - SANE backend for Kodak DC210 Digital Camera

DESCRIPTION
       The  sane-dc210	library	 implements  a	SANE (Scanner Access Now Easy)
       backend that provides  access  to  the  Kodak  DC210  camera.  THIS  IS
       EXTREMELY ALPHA CODE!  USE AT YOUR OWN RISK!!

DEVICE NAMES
       The  current  version  of the backend only allows one camera to be con‐
       nected.	The device name is always "0".

CONFIGURATION
       The contents of the dc210.conf specify the serial port and baud rate to
       use.  The baud rate specifies the maximum rate to use while downloading
       pictures.  (The camera is always	 initialized  using  9600  baud,  then
       switches	 to  the higher rate).	On my 90MHz Pentium, I usually have no
       problems downloading at 115200 baud as long as the system is not exces‐
       sively  busy  and  the "interrupt-unmask flag" is set in the IDE driver
       (hdparm -u1).  Supported baud rates are: 9600, 19200, 38400, 57600, and
       115200.

       The  dumpinquiry	 line  causes  some information about the camera to be
       printed.

       cmdrespause specifies how many usec (1,000,000ths of a) between writing
       the  command  and reading the result should be used. 125000 seems to be
       the lowest I could go reliably.

       breakpause is the time in 1,000,000ths of a usec	 between  sending  the
       "back to default" break sending commands.

       Empty  lines  and  lines	 starting with a hash mark (#) are ignored.  A
       sample configuration file is shown below:

	      port=/dev/ttyS0
	      # this is a comment
	      baud=115200
	      dumpinquiry
	      cmdrespause=125000
	      breakpause=1000000

FILES
       /system/resources/sane-backends/1.0.18/etc/sane.d/dc210.conf
	      The  backend  configuration  file	 (see  also   description   of
	      SANE_CONFIG_DIR below).

       /system/resources/sane-backends/1.0.18/lib/sane/libsane-dc210.a
	      The static library implementing this backend.

       /system/resources/sane-backends/1.0.18/lib/sane/libsane-dc210.so
	      The shared library implementing this backend (present on systems
	      that support dynamic loading).

ENVIRONMENT
       SANE_CONFIG_DIR
	      This environment variable specifies the list of directories that
	      may contain the configuration file.  Under UNIX, the directories
	      are separated by a colon (`:'), under OS/2, they	are  separated
	      by a semi-colon (`;').  If this variable is not set, the config‐
	      uration file is searched in two default directories: first,  the
	      current	 working   directory   (".")   and   then   in	 /sys‐
	      tem/resources/sane-backends/1.0.18/etc/sane.d.  If the value  of
	      the environment variable ends with the directory separator char‐
	      acter, then the  default	directories  are  searched  after  the
	      explicitly   specified   directories.    For   example,  setting
	      SANE_CONFIG_DIR to "/tmp/config:" would  result  in  directories
	      "tmp/config",	".",	 and	 "/system/resources/sane-back‐
	      ends/1.0.18/etc/sane.d" being searched (in this order).

       SANE_DEBUG_DC210
	      If the library was compiled with debugging support enabled, this
	      environment  variable controls the debug level for this backend.
	      A value of 128 requests maximally copious debug output;  smaller
	      levels reduce verbosity.

SEE ALSO
       sane(7)

AUTHOR
       Brian J. Murrell

       This  backend  is  based	 somewhat on the dc25 backend included in this
       package by Peter Fales.

       The manpage was copied from the dc25 backend  and  somewhat  edited  by
       Henning Meier-Geinitz.

BUGS
       Known bugs/limitations are: ?

       More  general  comments,	 suggestions, and inquiries about frontends or
       SANE  should  go	  to   the   SANE   Developers	 mailing   list	  (see
       http://www.sane-project.org/mailing-lists.html  for details).  You must
       be subscribed to the list, otherwise your mail won't  be	 sent  to  the
       subscribers.

sane-backends 1.0.18		 15 July 2000			 sane-dc210(5)
[top]
                             _         _         _ 
                            | |       | |       | |     
                            | |       | |       | |     
                         __ | | __ __ | | __ __ | | __  
                         \ \| |/ / \ \| |/ / \ \| |/ /  
                          \ \ / /   \ \ / /   \ \ / /   
                           \   /     \   /     \   /    
                            \_/       \_/       \_/ 
More information is available in HTML format for server Syllable

List of man pages available for Syllable

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net