XOSVIEW(1)XOSVIEW(1)NAMExosview - X based system monitor
SYNOPSISxosview [options]
DESCRIPTIONxosview is a monitor which displays the status of several system param‐
eters. These include CPU usage, load average, memory, swap space, net‐
work usage and more. Each resource is displayed as a horizontal bar
which is separated into color coded regions showing how much of the
resource is being put to a particular use.
xosview runs on several platforms (Linux, NetBSD, FreeBSD, OpenBSD,
DragonflyBSD, some Solaris systems, IRIX 6.5, HPUX and GNU). Not all
of the meters described below are supported on all platforms. Some of
the meters may appear different depending upon the platform xosview is
running on. Note that *BSD is used as an abbreviation for all the sup‐
ported BSD operating systems (NetBSD, FreeBSD, OpenBSD, DragonflyBSD).
Load: Kernel reported load average
all platforms : load
Linux : load | CPU frequency
*BSD : load | CPU frequency
CPU Usage
Linux : user | nice | system | soft-interrupt | interrupt | io-wait
|
guest | niced guest | stolen | idle
*BSD : user | nice | system | interrupt | idle
IRIX : user | system | interrupt | wait | idle
HPUX : user | nice | system | interrupt | idle
Memory Usage
Linux : used | buffers | slab | map | cache | free
FreeBSD: active | inactive | wired | cache | free
DFBSD : active | inactive | wired | cache | free
OpenBSD: active | inactive | wired | free
NetBSD : active | inactive | wired | free
IRIX : kernel | fs | user | free
HPUX : text | used | other | free
GNU : active | inactive | wired | free
Swap Usage
Linux : used | free
*BSD : used | free
HPUX : used | free
GNU : used | free
Disk Usage: Throughput to/from local disk, per second
Linux : in | out | idle
*BSD : in | out | idle
Page Swapping: Pages to/from swap, per second
Linux : in | out | idle
*BSD : in | out | idle
HPUX : in | out | idle
GNU : in | out | idle
Network Usage
Linux : in | out | idle
*BSD : in | out | idle
GFX Usage: Framebuffer exchanges, per second
IRIX : swapbuffers
Interrupts: "leds" which blink when an interrupt occurs
Linux : IRQs
*BSD : IRQs
Interrupt Rate: Per second
*BSD : interrupts | free
Serial Port Status: "leds" which show the serial port parameters
Linux : LSR and MSR
Battery Level: charge and status of batteries
Linux : available | used
RAID: State of disks in a software RAID array
Linux : disk0 disk1 disk2 ... diskN | rebuild
Wireless Link
Linux : quality
Temperature sensors
Shows readings from temperature sensors.
Linux : ACPI or i2c/hwmon or Intel Core/AMD K8+ sensors
*BSD : i2c or Intel Core/AMD K8+ sensors
Typing a 'q' in the window will terminate xosview.
OPTIONS
Most of these command line options are just a convenient way to set one
or more of xosview's resources. Please see the RESOURCES section for
more details on what the resource is for.
-v
Displays the version number.
-name name
Sets the Resource name xosview will use (same as the -name
option for typical X applications like xterm). When performing
resource lookups, xosview will look under name, and then under
``xosview''. For an example, perform the following (as docu‐
mented in README.netbsd):
xrdb -merge Xdefaults.stipple
xosview-name xosvstipple &
xosview-name xosvstipplebw &
-display display
Sets the X display to display. This option overrides the
xosview*display resource.
-font font
Specifies the font xosview will use for labels. This option
overrides the xosview*font resource.
-title title
This option sets the name xosview will tell the window manager
to use for the X window and icon. This option overrides the
xosview*title resource.
-geometry geometry_string
Sets the X geometry to geometry_string. This option overrides
the xosview*geometry resource.
-captions
This option overrides the xosview*captions resource. It is
equivalent to setting xosview*captions to "False".
+captions
This option overrides the xosview*captions resource. It is
equivalent to setting xosview*captions to "True".
-labels
This option overrides the xosview*labels resource. It is equiv‐
alent to setting xosview*labels to "False".
+labels
This option overrides the xosview*labels resource. It is equiv‐
alent to setting xosview*labels to "True".
-usedlabels
This option overrides the xosview*usedlabels resource. It is
equivalent to setting xosview*usedlabels to "False".
+usedlabels
This option overrides the xosview*usedlabels resource. It is
equivalent to setting xosview*usedlabels to "True".
-cpu
This option overrides the xosview*cpu resource. It is equiva‐
lent to setting xosview*cpu to "False".
+cpu
This option overrides the xosview*cpu resource. It is equiva‐
lent to setting xosview*cpu to "True".
-load
This option overrides the xosview*load resource. It is equiva‐
lent to setting xosview*load to "False".
+load
This option overrides the xosview*load resource. It is equiva‐
lent to setting xosview*load to "True".
-mem
This option overrides the xosview*mem resource. It is equiva‐
lent to setting xosview*mem to "False".
+mem
This option overrides the xosview*mem resource. It is equiva‐
lent to setting xosview*mem to "True".
-swap
This option overrides the xosview*swap resource. It is equiva‐
lent to setting xosview*swap to "False".
+swap
This option overrides the xosview*swap resource. It is equiva‐
lent to setting xosview*swap to "True".
-battery
This option overrides the xosview*battery resource. It is
equivalent to setting xosview*battery to "False".
+battery
This option overrides the xosview*battery resource. It is
equivalent to setting xosview*battery to "True".
-gfx
This option overrides the xosview*gfx resource. It is equiva‐
lent to setting xosview*gfx to "False".
+gfx
This option overrides the xosview*gfx resource. It is equiva‐
lent to setting xosview*gfx to "True".
-wireless
This option overrides the xosview*wireless resource. It is
equivalent to setting xosview*wireless to "False".
+wireless
This option overrides the xosview*wireless resource. It is
equivalent to setting xosview*wireless to "True".
-net
This option overrides the xosview*net resource. It is equiva‐
lent to setting xosview*net to "False".
+net
This option overrides the xosview*net resource. It is equiva‐
lent to setting xosview*net to "True".
-network maxbandwidth
-networkBW maxbandwidth
-networkBandwidth maxbandwidth
These options override the xosview*netBandwidth resource. They
cause xosview to display a meter that will shows network usage,
with a maximum bandwidth of maxbandwidth. Notice that setting
the bandwidth to 0 no longer disables the meter -- use the
``-net'' option instead.
-page
This option overrides the xosview*page resource. It is equiva‐
lent to setting xosview*page to "False".
+page
This option overrides the xosview*page resource. It is equiva‐
lent to setting xosview*page to "True".
-pagespeed val
This option overrides the xosview*pageBandWidth resource. The
resource xosview*pageBandWidth will be set to val.
-disk
This option overrides the xosview*disk resource. It is equiva‐
lent to setting xosview*disk to "False".
+disk
This option overrides the xosview*disk resource. It is equiva‐
lent to setting xosview*disk to "True".
-int
This option overrides the xosview*int resource. It is equiva‐
lent to setting xosview*int to "False".
+int
This option overrides the xosview*int resource. It is equiva‐
lent to setting xosview*int to "True".
-ints +ints
-interrupts +interrupts
Equivalent to -int and +int.
-irqrate
This option overrides the xosview*irqrate resource. It is
equivalent to setting xosview*irqrate to "False".
+irqrate
This option overrides the xosview*irqrate resource. It is
equivalent to setting xosview*irqrate to "True".
-intrate +intrate
Equivalent to -irqrate and +irqrate.
-lmstemp
This option overrides the xosview*lmstemp resource. It is
equivalent to setting xosview*lmstemp to "False".
+lmstemp
This option overrides the xosview*lmstemp resource. It is
equivalent to setting xosview*lmstemp to "True".
-coretemp
This option overrides the xosview*coretemp resource. It is
equivalent to setting xosview*coretemp to "False".
+coretemp
This option overrides the xosview*coretemp resource. It is
equivalent to setting xosview*coretemp to "True".
-acpitemp
This option overrides the xosview*acpitemp resource. It is
equivalent to setting xosview*acpitemp to "False".
+acpitemp
This option overrides the xosview*acpitemp resource. It is
equivalent to setting xosview*acpitemp to "True".
-bsdsensor
This option overrides the xosview*bsdsensor resource. It is
equivalent to setting xosview*bsdsensor to "False".
+bsdsensor
This option overrides the xosview*bsdsensor resource. It is
equivalent to setting xosview*bsdsensor to "True".
-xrm resource_string
This switch allows any of xosview's resources to be set on the
command line. An example of how the xosview*memFreeColor could
be set using this option is shown below (Note the use of " to
prevent the shell from expanding ´*´ or from creating two sepa‐
rate arguments, ´xosview*memfreeColor:´ and ´purple´):
-xrm "xosview*memFreeColor: purple"
X RESOURCES
The following is a list of X resources supported by xosview. Each has
a default value assigned to it. These values can be found in the file
Xdefaults which can be obtained in the source distribution of xosview.
They can be overridden in the usual places (/usr/lib/X11/app-
defaults/XOsview, $HOME/.Xdefaults, etc.).
It should be noted that it is OK to have a resource defined for a port
of xosview that does not support the feature the resource configures.
Xosview will simply ignore the resources that are set for it but not
supported on a given platform.
General Resources
xosview*title: name
The string that xosview will use for the X window title. Nor‐
mally xosview will use 'xosview@machine_name' for a title. This
resource overrides the default behavior.
xosview*geometry: geometry_string
This is a standard X geometry string that defines the size and
location of the X window used by xosview.
xosview*display: name
The name of the display where xosview will contact the X server
for drawing its window.
xosview*pixmapName: name
The filename of an X pixmap (xpm) file for use as a background
image.
xosview*captions: (True or False)
If True then xosview will display meter captions.
xosview*labels: (True or False)
If True then xosview will display meter labels.
xosview*meterLabelColor: color
The color to use for the meter labels.
xosview*usedlabels: (True or False)
If True then xosview will display labels that show the percent‐
age of the resource (or absolute amount, depending on the meter)
being used. This option requires that the labels option also be
set to True.
xosview*usedLabelColor: color
The color to use for "used" labels.
xosview*borderwidth: width
The width of the border for the xosview window.
xosview*font: font
This is the font that xosview will use.
xosview*background: color
This is the color that will be used for the background.
xosview*foreground: color
This is the color that will be used for the foreground.
xosview*enableStipple: (True or False)
Change to true to try stipple support. This is primarily for
users stuck with 1-bit monitors/display cards. Try setting
enableStipple true. Please give us feedback on this, if you use
it. It needs some more work, but no one has given us any feed‐
back so far.
xosview*graphNumCols: number
This defines the number of sample bars drawn when a meter is in
scrolling graph mode. This also has the side-effect of defining
the width of the graph columns. This is only used by meters
which have graph mode enabled.
Load Meter Resources
xosview*load: (True or False)
If True then xosview will display a load meter.
xosview*loadProcColor: color
This is the color that the load meter will use to display the
load average when it is below the warning threshold.
xosview*loadWarnColor: color
This is the color that the load meter will use once the load
average is above the warning but below the critical load thresh‐
old.
xosview*loadCritColor: color
This is the color that the load meter will use once the load
average is above critical load threshold.
xosview*loadIdleColor: color
The load meter will use this color to display the idle field.
xosview*loadPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the load meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*loadWarnThreshold: int
This number (which must be an integer >= 1) sets the value at
which the loadmeter changes its status and color from "normal"
to "warning". The default value is the number of processors.
xosview*loadCritThreshold: int
This number (which must be an integer >= 1) sets the value at
which the loadmeter changes its status and color from "warning"
to "critical". The default value is four times the warning
threshold.
xosview*loadDecay: (True or False)
You should probably leave this at the default value (False).
The load is already a time-averaged value!
xosview*loadGraph: (True or False)
If this is set to True then the load meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*loadUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
xosview*loadCpuSpeed: (True or False)
Display the current CPU speed in the load meter.
CPU Meter Resources
xosview*cpu: (True or False)
If True then xosview will display a cpu meter. On Linux and
IRIX SMP machines, the resource cpuFormat defines how meters are
created for multiple CPUs.
xosview*cpuUserColor: color
The cpu meter will use this color to display the cpu user time
field.
xosview*cpuNiceColor: color
The cpu meter will use this color to display the cpu nice time
field.
xosview*cpuSystemColor: color
The cpu meter will use this color to display the cpu system time
field.
xosview*cpuInterruptColor: color
The cpu meter will use this color to display the cpu hard inter‐
rupt time field.
xosview*cpuSInterruptColor: color
The cpu meter will use this color to display the cpu soft inter‐
rupt time field.
xosview*cpuWaitColor: color
The cpu meter will use this color to display the cpu IO waiting
time field.
xosview*cpuGuestColor: color
The cpu meter will use this color to display the cpu virtualiza‐
tion guest time field.
xosview*cpuNiceGuestColor: color
The cpu meter will use this color to display the cpu niced vir‐
tualization guest time field.
xosview*cpuStolenColor: color
The cpu meter will use this color to display the cpu involuntary
wait time field.
xosview*cpuFreeColor: color
The cpu meter will use this color to display the cpu idle time
field.
xosview*cpuPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the cpu meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*cpuDecay: (True or False)
If True then the cpu meter will be split vertically in two. The
top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*cpuGraph: (True or False)
If this is set to True then the cpu meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*cpuUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
xosview*cpuFormat: (single, all, both or auto)
If `single', only a cumulative meter for all CPU usage is cre‐
ated. `all' creates a meter for each CPU, but no cumulative
meter. `both' creates one cumulative meter and one for each CPU.
`auto' makes a choice based on the number of CPUs found.
xosview*cpuFields: USED/USR/NIC/SYS/INT/SI/HI/WIO/GST/NGS/STL/IDLE
The set of fields to show in Linux CPU meter instead of the
default. Possible fields are:
USED:
Combine all used CPU time into one field. This is the sum
of user, nice, system, soft and hard interrupts, guest,
niced guest and stolen times. None of these, except
stolen, may be defined together with `USED'.
IDLE:
Time spent doing nothing. Includes I/O wait if it is not
defined separately.
USR:
Time spent in user mode processes. Includes nice, guest
and niced guest if those are not defined separately.
NIC:
Time spent in niced user mode processes. Includes niced
guest if neither it nor guest is not defined separately.
SYS:
Time spent in kernel code. Includes soft and hard inter‐
rupt as well as stolen time if those are not defined sep‐
arately.
INT:
Combines soft and hard interrupt handling times into one
field.
SI:
Time the kernel used to handle soft interrupts. Available
on Linux kernel 2.6.0 and higher.
HI:
Time the kernel used to handle hard interrupts. Available
on Linux kernel 2.6.0 and higher.
WIO:
Time spent waiting for I/O to complete. Available on
Linux kernel 2.6.0 and higher.
GST:
Time spent running guest OS in virtual machine. Includes
niced guest if it is not defined separately. Available on
Linux kernel 2.6.24 and higher.
NGS:
Time spent running niced guest OS in virtual machine.
Available on Linux kernel 2.6.32 and higher.
STL:
Involuntary wait time when running as guest in virtual
machine. Available on Linux kernel 2.6.11 and higher.
Most combinations are possible (see above for restrictions), but
at least `USED' or `USR' and `SYS' need to be defined. `IDLE'
field is added automatically.
Memory Meter Resources
xosview*mem: (True or False)
If True then xosview will display a mem meter.
xosview*memUsedColor: color
The mem meter will use this color to display the used memory
field.
xosview*memSharedColor: color
The mem meter will use this color to display the shared memory
field.
xosview*memBufferColor: color
The mem meter will use this color to display the buffer memory
field.
xosview*memCacheColor: color
The mem meter will use this color to display the cache memory
field.
xosview*memFreeColor: color
The mem meter will use this color to display the free memory
field.
xosview*memSharedColor: color
The mem meter will use this color to display the shared memory
field.
xosview*memTextColor: color
The mem meter will use this color to display the HP text memory
field.
xosview*memOtherColor: color
The mem meter will use this color to display the HP ``other''
memory field.
xosview*memActiveColor: color
The mem meter will use this color to display the *BSD active
memory field.
xosview*memInactiveColor: color
The mem meter will use this color to display the *BSD inactive
memory field.
xosview*memWiredColor: color
The mem meter will use this color to display the *BSD wired mem‐
ory field.
xosview*memSlabColor: color
The mem meter will use this color to display the Linux in-kernel
data structures field.
xosview*memMapColor: color
The mem meter will use this color to display the Linux memory
mapped files field.
xosview*memPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the mem meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*memDecay: (True or False)
If True then the mem meter will be split vertically in two. The
top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*memGraph: (True or False)
If this is set to True then the mem meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*memUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Swap Meter Resources
xosview*swap: (True or False)
If True then xosview will display a swap meter.
xosview*swapUsedColor: color
The swap meter will use this color to display the used swap
field.
xosview*swapFreeColor: color
The swap meter will use this color to display the free swap
field.
xosview*swapPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the swap meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*swapDecay: (True or False)
If True then the swap meter will be split vertically in two.
The top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*swapGraph: (True or False)
If this is set to True then the swap meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*swapUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Page Swapping Meter Resources
xosview*page: (True or False)
If True then xosview will display a page meter.
xosview*pageBandWidth: maxEvents
This number is used to specify the expected maximum bandwidth
(in events / sec) for the page meter. When the expected maximum
bandwidth (maxEvents) is exceeded then the page meter will dis‐
play the relative percentage of page swapping (25% in, 75% out).
xosview*pageInColor: color
The page meter will use this color to display the page-in field.
xosview*pageOutColor: color
The page meter will use this color to display the page-out
field.
xosview*pageIdleColor: color
The page meter will use this color to display the idle field.
xosview*pagePriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the page meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*pageDecay: (True or False)
If True then the page meter will be split vertically in two.
The top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*pageGraph: (True or False)
If this is set to True then the page meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*pageUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Gfx Meter Resources
xosview*gfx: (True or False)
If True xosview will display the GfxMeter. The value is sampled
once per second, due to the usage of sadc to sample data.
xosview*gfxWarnColor: color
This is the color that the gfx meter will use once the warn
state is reached.
xosview*gfxAlarmColor: color
This is the color that the gfx meter will use once the alarm
state is reached.
xosview*gfxSwapColor: color
This is the color that the gfx meter will use in normal state
xosview*gfxIdleColor: color
The gfx meter will use this color to display the idle field.
xosview*gfxPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the gfx meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*gfxWarnThreshold: int
This number (which must be an integer >= 1) of swapbuffers per
second and pipe at which the gfxmeter changes its status and
color from "normal" to "warn". The default value is 60.
xosview*gfxAlarmThreshold: int
This number (which must be an integer >= gfxWarnThreshold) of
swapbuffers per second and pipe at which the gfxmeter changes
its status and color from "warn" to "alarm". The default value
is 120.
xosview*gfxDecay: (True or False)
You should probably leave this at the default value (False).
The gfx does not work in decay mode.
xosview*gfxGraph: (True or False)
If this is set to True then the gfx meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*gfxUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Network Meter Resources
xosview*net: (True or False)
If True xosview will display the NetMeter. Linux users will
have to configure their kernels and setup some ip accounting
rules to make this work. See the file README.linux which comes
with the xosview distribution for details.
xosview*netBandwidth: maxBytes
This number is used to specify the expected maximum bandwidth
(in bytes / sec) for the meter. When the expected maximum band‐
width (maxBytes) is exceeded then the network meter will display
the relative percentage of network usage (25% incoming, 75% out‐
going).
xosview*netIface: interface
If False, xosview will display the data received/transmitted by
any of the network interfaces. Otherwise, xosview will only dis‐
play the data received/transmitted by the specified network
interface. If the name is prepended with '-' sign, the data in
that interface is ignored.
xosview*netInColor: color
The net meter will use this color to display the incoming field.
xosview*netOutColor: color
The net meter will use this color to display the outgoing field.
xosview*netBackground: color
This is the color that the network meter will use for the "idle"
field.
xosview*netPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the net meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*netDecay: (True or False)
If True then the net meter will be split vertically in two. The
top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*netGraph: (True or False)
If this is set to True then the net meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*netUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
NFSStats (Client) Resources
xosview*NFSStats: (True or False)
If True then xosview will display a meter to monitor NFS client
stats.
xosview*NFSStatReTransColor: color
The color to be used for retransmit stats.
xosview*NFSStatAuthRefrshColor: color
The color to be used for auth refresh stats.
xosview*NFSStatCallsColor: color
The color to be used for call stats.
xosview*NFSStatIdleColor: color
The color to be used for idle stats.
NFSDStats (Server) Resources
xosview*NFSDStats: (True or False)
If True xosview will display a meter for NFS server/daemon
stats.
xosview*NFSDStatCallsColor: color
The color to be used for call stats.
xosview*NFSDStatBadCallsColor: color
The color to be used for bad stats.
xosview*NFSDStatUDPColor: color
The color to be used for UDP stats.
xosview*NFSDStatTCPColor: color
The color to be used for TCP stats.
xosview*NFSDStatIdleColor: color
The color to be used for idle stats.
Serial Meter Resources
xosview*serial(0-9): (True, False, or portBase)
If True then xosview will display a serial meter for ttySx. The
portbase will be autodetected. Because autodetection can fail,
(if the port is locked by ppp/slip for example) you can specify
the portbase instead of "True". If a portBase is used then
xosview will use it instead of trying to autodetect.
For this to work on Linux xosview needs to be suid root in order
to have access to the ports. See the file README.linux which
comes with the xosview distribution for more details.
xosview*serialOnColor: color
This is the color the serial meter will use for bits that are
set.
xosview*serialOffColor: color
This is the color the serial meter will use for bits that are
not set.
xosview*serialPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the serial meter waits between updates.
A value of 1 has xosview update the meter 10 times per second
(the fastest). A value of 600 would cause xosview to update the
meter once a minute.
Interrupt Meter Resources
xosview*interrupts: (True or False)
If True then xosview will display an interrupt meter.
xosview*intSeparate: (True of False)
If True then xosview will display one interrupt meter per CPU on
SMP machines. If False only one meter is displayed. Default:
True.
xosview*intOnColor: color
This is the color that will be used to show "active" interrupts.
xosview*intOffColor: color
This is the color that will be used to show "inactive" inter‐
rupts.
xosview*intPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the int meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
Lm Sensors Temperature Resources
xosview*lmstemp: (True or False)
If True then xosview will display a lmstemp meter.
xosview*lmstempHighest: 100
Highest temp value displayed, default 100.
xosview*lmstempActColor: color
Color of actual temperature.
xosview*lmstempHighColor: color
Color above alarm temperature, also used to indicate alarm.
xosview*lmstempIdleColor: color
Color between actual and alarm temperatures.
xosview*lmstempN: filename
Name of temperature file from /proc/sys/dev/sensors/*/* or
/sys/class/hwmon/*/*, N=1... Also absolute path is accepted.
Note that if more files with same name exists, only the first is
found unless absolute path is used. For example,
xosview*lmstemp1: temp
xosview*lmstemp2: remote_temp
xosview*lmstempLabelN: Labelstring
N-th label for above temperatures, default is TMP.
xosview*lmstempPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the lmstemp meter waits between updates.
A value of 1 has xosview update the meter 10 times per second
(the fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*lmstempUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
ACPI Temperature Resources
xosview*acpitemp: (True or False)
If True then xosview will display a acpitemp meter.
xosview*acpitempHighest: 100
Highest temp value displayed, default 100. If acpihighN is
given, the value is read from there instead.
xosview*acpitempActColor: color
Color of actual temperature.
xosview*acpitempHighColor: color
Color above alarm temperature, also used to indicate alarm.
xosview*acpitempIdleColor: color
Color between actual and alarm temperatures.
xosview*acpitempN: filename
Name of temperature file from /proc/acpi/thermal_zone or
/sys/devices/virtual/thermal. Note that the last directory part
must be given, e.g. TZ0/temperature. Absolute path can also be
used.
xosview*acpihighN: filename
Name of high value/trip point file from /proc/acpi/thermal_zone
or /sys/devices/virtual/thermal, or an absolute path to one.
xosview*acpitempLabelN: Labelstring
N-th label for above temperatures, default is TMP.
xosview*acpitempPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the acpitemp meter waits between
updates. A value of 1 has xosview update the meter 10 times per
second (the fastest). A value of 600 would cause xosview to
update the meter once a minute.
xosview*acpitempUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Intel Core / AMD K8+ Temperature Sensor Resources
xosview*coretemp: (True or False)
If True then xosview will display a coretemp meter.
xosview*coretempHighest: 100
Highest temp value displayed, default 100. If none is given,
TjMax value is used, if available.
xosview*coretempActColor: color
Color of actual temperature.
xosview*coretempHighColor: color
Color above alarm temperature, also used to indicate alarm.
xosview*coretempIdleColor: color
Color between actual and alarm temperatures.
xosview*coretempNPackage: 0
The number of physical CPU for meter N on Linux. Currently only
one physical CPU can be shown per meter.
xosview*coretempNDisplayType: (separate, average or maximum)
This resource tells xosview how to display the temperature for
meter N. The formats work as follows:
separate:
Display one meter for each CPU core of a multi-core CPU.
This is the default.
average:
Display average temperature of a multi-core CPU.
maximum:
Display the highest core temperature of a multi-core CPU.
xosview*coretempPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the coretemp meter waits between
updates. A value of 1 has xosview update the meter 10 times per
second (the fastest). A value of 600 would cause xosview to
update the meter once a minute.
xosview*coretempUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
*BSD Sensor Resources
xosview*bsdsensor: (True or False)
If True then xosview will display a bsdsensor meter.
xosview*bsdsensorActColor: color
Color of actual value.
xosview*bsdsensorHighColor: color
Color above alarm value, also used to indicate alarm.
xosview*bsdsensorIdleColor: color
Color between actual and alarm values.
xosview*bsdsensorN: name.type
xosview*bsdsensorHighN: name.type
Here, the name is the sensor driver, and type is the wanted
value. Also static numerical value is accepted for bsdsen‐
sorHighN.
You can find the correct pair for OpenBSD and DragonflyBSD with
systat command, e.g.
xosview*bsdsensor1: it0.temp1
xosview*bsdsensorHigh1: 100
On NetBSD, you can find the driver name with envstat command.
Value name for the actual reading is typically 'cur-value' and
for alarm level 'max-critical', e.g.
xosview*bsdsensor2: coretemp0.cur-value
xosview*bsdsensorHigh2: coretemp0.max-critical
For all possible NetBSD value names, refer to envstat source
code.
FreeBSD has no sensor drivers as of version 9.0. However, ACPI
thermal zones can be used by defining the sysctl node below
hw.acpi.thermal, e.g.
xosview*bsdsensor1: tz0.temperature
xosview*bsdsensorHigh1: tz0._CRT
ACPI thermal zones work similarly on DragonflyBSD as well.
xosview*bsdsensorLabelN: Labelstring
N-th label for above meters, default is SENN.
xosview*bsdsensorPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the bsdsensor meter waits between
updates. A value of 1 has xosview update the meter 10 times per
second (the fastest). A value of 600 would cause xosview to
update the meter once a minute.
xosview*bsdsensorUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Battery Meter Resources
xosview*battery: (True or False)
If True then xosview will display a battery meter. Linux users
will need to have APM or ACPI support in their kernels for this
to work. For both APM and ACPI, xosview shows the status/sum of
all batteries. Additionally - the legend text gets
changed/adjusted to reflect the current state (charg‐
ing/low/critical/etc.) of the battery/batteries.
xosview*batteryLeftColor: color
This is the color that will be used to show the amount of bat‐
tery power left.
xosview*batteryUsedColor: color
This is the color that will be used to show the amount of bat‐
tery power used.
xosview*batteryChargeColor: color
This is the color that will be used as 'left' - if the batteries
get charged.
xosview*batteryFullColor: color
This is the color that will be used as 'left' - if the batteries
are fully charged. APM and ACPI does provide this info, but not
all machines actually do so.
xosview*batteryLowColor: color
APM only - the 'left' color that will indicate a low battery.
Depends on the machine - e.g. below 25% remaining capacity.
xosview*batteryCritColor: color
APM case: the 'left' color if APM indicates 'critical' state.
(less than 5%) ACPI case: the 'left' color if the remaining
capacity is below the alarm value. (which can be set by the
user in /proc/acpi/battery/BAT[01]/alarm )
xosview*batteryNoneColor: color
If no battery is present - or all batteries get removed (while
on AC).
xosview*batteryPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the battery meter waits between updates.
A value of 1 has xosview update the meter 10 times per second
(the fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*batteryUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Wireless Meter Resources
xosview*wireless: (True or False)
If True then xosview will display the link quality of each wire‐
less connection. Note that the graph will *never* show up, if
you don't have any wireless devices, or no wireless extensions
in the kernel (/proc/net/wireless). Default is true.
xosview*PoorQualityColor: color
This is the color for the quality field when between 0 and 6.
xosview*FairQualityColor: color
This is the color for the quality field when between 7 and 14.
xosview*GoodQualityColor: color
This is the color for the quality field when higher than 14.
xosview*wirelessUsedColor: color
This is the background color.
xosview*wirelessPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the wireless meter waits between
updates. A value of 1 has xosview update the meter 10 times per
second (the fastest). A value of 600 would cause xosview to
update the meter once a minute.
xosview*wirelessDecay: (True or False)
If True then the wireless meter will be split vertically in two.
The top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*wirelessUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Disk Meter Resources
xosview*disk: (True or False)
If True then xosview will display a disk meter.
xosview*diskInColor: color
The disk meter will use this color to display the reads field.
xosview*diskOutColor: color
The disk meter will use this color to display the writes field.
xosview*diskIdleColor: color
The disk meter will use this color to display the idle field.
xosview*diskBandwidth: bandwidth
This number is used to specify the expected maximum bandwidth in
bytes per second for the disk meter.
xosview*diskWriteColor: color
This color will be used for the linux meter to show writes.
xosview*diskReadColor: color
This color will be used for the linux meter to show reads.
xosview*diskPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the disk meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*diskDecay: (True or False)
If True then the disk meter will be split vertically in two.
The top half will show the instantaneous state, while the bottom
half will display a decaying average of the state.
xosview*diskGraph: (True or False)
If this is set to True then the disk meter will be drawn as a
horizontally scrolling bargraph showing the state value verses
time.
xosview*diskUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
RAID Meter Resources
xosview*RAID: (True or False)
If True then xosview will display a RAID meter.
xosview*RAIDdevicecount: int
Please enter your RAID device count (n) here or 0 if you don't
have any supported RAID devices. xosview then will display n
RAID state displays.
xosview*RAIDdiskOnlineColor: color
xosview*RAIDdiskFailureColor: color
These colors will be used for indicating working/online or
failed/offline disks. The order (from left to right) is the same
as in /proc/mdstat.
xosview*RAIDresyncdoneColor: color
xosview*RAIDresynctodoColor: color
xosview*RAIDresynccompleteColor: color
If a resync/rebuild of the RAID array is in progress, the "done"
and "todo" colors will be used. If no rebuild/resync is running,
then the "complete" color will be shown.
xosview*RAIDPriority: priority
This number (which must be an integer >= 1) sets the number of
tenths of a second that the RAID meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the
fastest). A value of 600 would cause xosview to update the
meter once a minute.
xosview*RAIDUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display "used" labels. The
formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
OBTAINING
This version of xosview is distributed from the following site:
http://www.pogo.org.uk/~mark/xosview/
AUTHORS
Mike Romberg <mike.romberg@noaa.gov>
Original author, Linux and HPUX ports.
Brian Grayson <bgrayson@netbsd.org>
NetBSD port and most of the nice enhancements for version 1.4,
initial work on FreeBSD port.
Scott McNab <jedi@tartarus.uwa.edu.au>
Added the scrolling graph mode.
Tom Pavel <pavel@slac.stanford.edu>
Most of the FreeBSD support, more resource-handling improve‐
ments.
Greg Onufer <exodus@cheers.bungi.com>
SunOS port.
Stefan Eilemann <eilemann@gmail.com>
IRIX 6.5 port.
Sheldon Hearn <axl@iafrica.com>
FreeBSD libdevstat-based diskmeter support.
David W. Talmage <talmage@jefferson.cmf.nrl.navy.mil>
Added battery-meter support to NetBSD.
Oleg Safiullin <form@openbsd.org>
OpenBSD interrupt-meter support.
Werner Fink <werner@suse.de>
Originator of the loadmeter.
Massimiliano Ghilardi <ghilardi@cibs.sns.it>
Linux pagemeter.
Carsten Schabacker <cschaba@spock.central.de>
Made extensions to the serial-meter.
Paal Beyer <pbeyer@online.no>
Ported the linux memstat kernel module to linux-2.1
Jerome Forissier <forissier@isia.cma.fr>
Author of the Linux SMP kernel patch which xosview uses to dis‐
play meters for each CPU.
Tomer Klainer <mandor@cs.huji.ac.il>
Initial port to BSDI.
Arno Augustin <Arno.Augustin@3SOFT.de>
Solaris disk and network meters.
Alberto BARSELLA <ishark@lsh01.univ-lille1.fr>
Fixes for linux diskmeter + ip_chains support
Thomas Waldmann <ThomasWaldmann@gmx.de>
Linux raid meter, bitfieldmeter. Many cosmetic fixes.
Leopold Toetsch <lt@toetsch.at>
Linux lms temp meter.
David O'Brien <obrien@nuxi.com>
FreeBSD 4.* updates, and a few other suggestions.
Christos Zoulas <christos@netbsd.org>
C++ standard compliance and other NetBSD fixes.
Tim Ehlers <tehlers@gwdg.de>
Wireless Link-Meter for Linux.
Mark Hills <mark@pogo.org.uk>
Bug fixes and general caretaking.
Tomi Tapper <tomi.o.tapper@student.jyu.fi>
Temperature sensor, and FreeBSD updates.
Raymond S Brand (rsbx@acm.org)
Misc fixes.
And many others who have sent in small fixes and improvements.
3rd Berkeley DistributionXOSVIEW(1)
