SCREEN(HW) XENIX System V SCREEN(HW)screen - tty[01-n], color, monochrome, ega, vga display
adapter and video monitor
Description
The tty[01-n] device files provide character I/O between the
system and the video display monitor and keyboard. Each
file corresponds to a separate teletype device. Although
there is a maximum of 12 screens, the exact number available
(n) depends upon the amount of memory in the computer. The
screens are modeled after a 25 line, 80 column ASCII
terminal, unless specified otherwise.
System error messages from the kernel are written to
/dev/console, which is normally the current multiscreen. If
the /dev/console is the default output device for system
error messages, and the display being used is switched to
graphics mode, console messages are not displayed. When the
video device returns to text mode, a notice message is
displayed and the text of the kernel error can be recovered
from usr/adm/messages.
Although all tty[01-n] devices may be open concurrently,
only one of the corresponding devices can be active at any
given time. The active device displays its own screen and
takes sole possession of the keyboard. It is an error to
attempt to access the color, monochrome, or ega file when no
corresponding adapter exists or no multiscreens are
associated with it.
To get to the next consecutive screen, enter Ctrl-PrtSc
using the Ctrl key, and the PrtSc key. Any active screen
may be selected by entering alt-Fn, where Fn is one of the
function keys. For example, F1 refers to the tty01 device.
Control Modes
Multiscreens can be reassigned to different adapters (in
multi-adapter systems) with these ioctls :
SWAPMONO Selects the monochrome display as
the output device for the
multiscreen.
SWAPCGA Selects the regular color display
as the output device for the
multiscreen.
Page 1 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
SWAPEGA Selects the enhanced color display
as the output device for the
multiscreen.
SWAPVGA Selects the video graphics array
color display as the output device
for the multiscreen.
To find out which display adapter type is currently attached
to the multiscreen, you can use ioctl(S) with the following
request:
CONS_CURRENT Returns the display adapter type
currently associated with the
multiscreen. The return value can
be one of: MONO, CGA, EGA, or VGA.
Display Modes
The following ioctls can be used to change the video display
mode:
SW_B80x25 Selects 80x25 black and white text
display mode. (MONO, CGA, EGA,
VGA)
SW_C80x25 Selects 80x25 color text display
mode. (CGA, EGA, VGA)
SW_B40x25 Selects 40x25 black and white text
display mode. (MONO, CGA, EGA,
VGA)
SW_C40x25 Selects 40x25 color text display
mode. (CGA, EGA, VGA)
SW_BG320 Selects 320x200 black and white
graphics display mode. (CGA, EGA,
VGA)
SW_CG320 Selects 320x200 color graphics
display mode. (CGA, EGA, VGA)
SW_BG640 Selects 640x200 black and white
graphics display mode. (CGA, EGA,
VGA)
Page 2 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
SW_EGAMONO80x25 Selects EGA (Enhanced Graphics
Adapter) mode 7 - emulates support
provided by the monochrome display.
(EGA, VGA)
SW_EGAMONOAPA Selects EGA support for 640x350
graphics display mode (EGA mode F).
(EGA with mono monitor)
SW_ENHMONOAPA2 Selects EGA mode F*. (EGA with
mono monitor)
SW_ENHB40x25 Selects enhanced EGA support for
40x25 black and white text display
mode. (EGA, VGA)
SW_ENHC40x25 Selects enhanced EGA support for
the 40x25 color text display mode.
(EGA, VGA)
SW_ENHB80x25 Selects enhanced EGA support for
80x25 black and white text display
mode. (EGA, VGA)
SW_ENHC80x25 Selects enhanced EGA support for
80x25 color text display mode.
(EGA, VGA)
SW_ENHB80x43 Selects enhanced EGA support for
80x43 black and white text display
mode. (EGA, VGA)
SW_ENHC80x43 Selects enhanced EGA support for
80x43 color text display mode.
(EGA, VGA)
SW_CG320_D Selects EGA support for 320x200
graphics display mode. (EGA mode
D.) (EGA, VGA)
SW_CG640_E Selects EGA support for 640x200
graphics display mode (EGA mode E).
(EGA, VGA)
SW_CG640x350 Selects EGA support for 640x350
graphics display mode (EGA mode
10). (EGA, VGA)
Page 3 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
SW_ENH_CG640 Selects EGA mode 10*. (EGA, VGA)
SW_MCAMODE Reinitializes the monochrome
adapter. (MONO)
SW_VGA40x25 Selects VGA support for the 40x25
color text display mode (VGA mode
1+). (VGA)
SW_VGA80x25 Selects VGA support for the 80x25
black and white text display mode
(VGA mode 2+). (VGA)
SW_VGAM80x25 Selects VGA mode 7+ - emulates
support provided by the monochrome
display. (VGA with mono monitor)
SW_VGA11 Selects VGA support for the 640x480
graphics display mode (VGA mode
11). (VGA)
SW_VGA12 Selects VGA support for the 640x480
graphics display mode (VGA mode
12). (VGA)
SW_VGA13 Selects VGA support for the 320x200
graphics display mode (VGA mode
13). (VGA)
Switching to an invalid display mode for a display device
will result in an error.
Getting Display Modes
The following ioctl() requests are provided to obtain
information about the current display modes:
CONS_GET Returns the current display mode
setting for current display
adapter. (All)
CGA_GET Returns the current display mode
setting of the color graphics
adapter. (CGA only)
EGA_GET Returns the current display mode
setting of the enhanced graphics
adapter. (EGA only)
Page 4 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
MCA_GET Returns the current display mode
setting of the monochrome adapter.
(MONO only)
VGA_GET Returns the current display mode of
the video graphics adapters. (VGA
only)
CONS_GETINFO Returns structure vid_info (below).
Size of structure (first field)
must be filled in by user.
struct vid_info
{
short size; /* must be first field */
short m_num; /* multiscreen number, 0 based */
ushort mv_row, mv_col; /* cursor position */
ushort mv_rsz, mv_csz; /* text screen size */
struct colors mv_norm, /* normal attributes */
mv_rev, /* reverse video attributes */
mv_grfc; /* graphic character attributes */
uchar_t mv_ovscan; /* border color */
uchar_t mk_keylock; /* caps/num/scroll lock */
};
CONS_6845INFO Returns structure m6845_info
(below). Size of structure (first
field) must be filled in by user.
struct m6845_info
{
short size; /* must be first field */
ushort screen_top; /* offset of screen in video */
ushort cursor_type; /* cursor shape */
};
CONSADP Returns number of multiscreen
displayed on adaptor associated
with that multiscreen.
GIO_ATTR Return value of ioctl is 6845-style
attribute byte in effect.
GIO_COLOR Return value of ioctl is zero or
one depending on whether the device
supports color
GIO_SCRNMAP Gets the 256-byte screen map table,
which is the mapping of ASCII
values (0-256) onto the PC video
ROM font characters (0-256). Note
that control characters (ASCII
values less than hex 20) have
Page 5 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
control functions and do not
display ROM characters (example:
^J is newline).
This is often used to map the low
font values that normally
correspond to ASCII control values
to higher ASCII values, thus
displaying the desired ROM
characters.
PIO_SCRNMAP Puts the 256-byte screen map table
(see GIO_SCRNMAP).
PIO_KEYMAP See keyboard(HW)
PIO_KEYMAP See keyboard(HW)
GIO_FONT8Xn Gets font, where is 8, 14, and 16.
Argument is a pointer to a font
table. Size of 8X8 font table is
8X256 bytes, 8X14 is 14X256 bytes,
etc.
PIO_FONT8Xn Puts font, where is 8, 14, and 16.
Argument is a pointer to a font
table. Size of 8X8 font table is
8X256 bytes, 8X14 is 14X256 bytes,
etc.
Memory Mapping Modes
The ioctl(S) routine is used to map the display memory of
the various devices into the user's data space.
Note that the MAP* ioctls map the memory associated with the
current mode. You must put the adapter into the desired
mode before performing mapping, or the pointers returned
will not be appropriate. Refer to your hardware manual for
details on various displays, adapters, and controllers.
These ioctl() requests can be used to map the display
memory:
MAPCONS Maps the display memory of the
adaptor currently being used into
the user's data space. (All)
Page 6 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
MAPMONO Maps the monochrome adapter's
display memory into the user's data
space. (MONO only)
MAPCGA Maps the color adapter's display
memory into the user's data space.
(CGA only)
MAPEGA Maps the enhanced graphics
adapter's display memory into the
user's data space. (EGA only)
MAPVGA Maps the video graphics adapter's
display memory into the user's data
space. (VGA only)
For example, the following code can be used to acquire a
pointer to the start of the user data space associated with
the color graphics adapter display memory:
char *dp;
int retval;
.
.
.
/* fd is a file descriptor for a
multiscreen device */
retval = ioctl (fd, MAPCONS,0L);
dp = (char *) retval;
.
.
.
Note that when the display memory is mapped into the user
space, the adapter's m6845 start address registers are not
set. The start address can be reset in two ways, so that
the start address of the display memory corresponds to the
upper left hand corner of the screen:
1. Switch modes with an ioctl() (the ``switch'' can be to
the present mode). See the ``Display Modes'' section
of this manual page.
2. Change the start address high and low address with the
in-on-port/out-on-port ioctl().
The in-on-port/out-on-port ioctl()'s can also be used to
determine the current value in the start address register,
and then set up a pointer to point to the offset in the
mapped-in data space.
Page 7 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
MAP_CLASS
Package ioctl that gives I/O privileges to an arbitrary
list of ports and maps an arbitrary frame buffer into
user's address space identified by a string found in
the struct vidclass vidclasslist[] located in
/usr/include/sys/vtkd.h.
EGA_IOPRIVL
VGA_IOPRIVL
These add the list of IO ports found on standard EGA
and VGA cards into the process' TSS IO permission
bitmap. This allows the process to access the EGA or
VGA io ports directly from user space with 386 IN and
OUT instructions.
KDDISPTYPE
This call returns display information to the user. The
argument expected is the buffer address of a structure
of type kd_disparam into which display information is
returned to the user. The kd_disparam structure is
defined as follows:
struct kd_disparam {
long type; /*display type*/
char *addr; /*display memory address*/
}
Possible values for the type field include:
KD_MONO (0x01), for the IBM monochrome display adapter.
KD_HERCULES (0x02), for the Hercules monochrome
graphics adapter.
KD_CGA (0x03), for the IBM color graphics adapter.
KD_EGA (0x04), for the IBM enhanced graphics adapter.
KD_VGA (0x05), for the IBM video graphics adapter.
KDDISPINFO
Returns struct kd_disparam, which contains adaptor type
and physical address of frame buffer.
KIOCSOUND
Start sound generation. Turn on sound. The arg is the
frequency desired. A frequency of 0 turns off the
sound. This is useful for generating tones while in
graphics mode.
KDGETLED
Page 8 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
Get keyboard LED status. The argument is a pointer to
a character. The character will be filled with a
boolean combination of the following values:
1 scroll lock
2 num lock
4 caps lock
KDSETLED
Set keyboard LED status. The argument is a character
whose value is the boolean combination of the values
listed under ``KDGETLED''.
KDMKTONE
Not supported. (See KIOCSOUND.)
KDADDIO
Not supported. (See MAP_CLASS.)
KDDELIO
Not supported. (See MAP_CLASS.)
KIOCDOSMODE
Not supported.
KIOCNONDOSMODE
Not supported.
KDSETMODE
(VP/IX only.) Set console in text or graphics mode.
The argument is of type integer, which should contain
one of the following values:
KD_TEXT 0x00 ( sets console to text mode )
KD_GRAPHICS 0x01 ( sets console in graphics mode )
Note, the user is responsible for programming the
color/graphics adaptor registers for the appropriate
graphical state.
KDGETMODE
(VP/IX only.) Get current mode of console. Returns
integer argument containing either KD_TEXT or
KD_GRAPHICS as defined in the KDSETMODE ioctl
description.
KDENABIO
Enable in's and out's to video adaptor ports. No
argument.
KDDISABIO
Disable in's and out's to video adaptor ports. No
argument.
KDGKBTYPE
Page 9 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
Always returns 0.
KDGKBMODE
Get keyborad translation mode, also known as scan code
mode. Mode is returned where arg points.
KDSKBMODE
Set keyborad translation mode, also known as scan code
mode.
KDGKBSTATE
Returns the state of the shifted, alt-, or control-
state of the keyboard. Returns a bollean combination
of:
1 shifted
2 control-
4 alt-
KIOCINFO
Always returns 0x6664.
KDMAPDISP
(VP/ix only) Maps display memory into user process
address space. Argument is a pointer to structure type
kd_memloc. This ioctl requires that a virtual 8086
subtask be attached to the current process. KDMAPDISP
should not be used by ordinary users to map the console
display; use MAPCONS.
KDUNMAPDISP
(VP/ix only) Unmap display memory from user process
address space. No argument required.
VT_SETMODE
Set the virtual terminal mode. The argument is a
pointer to a vt_mode structure, as defined below.
VT_GETMODE
Determine what mode the active virtual terminal is
currently in, either VT_AUTO or VT_PROCESS. The
argument to the ioctl is the address of the following
type of structure:
struct vt_mode {
char mode; /* VT mode */
char waitv; /* not implemented */
short relsig; /* signal to use for release request */
short acqsig; /* signal to use for display acquired */
short frsig; /* not implemented */
}
#define VT_AUTO 0x00 /* automatic VT switching */
Page 10 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
#define VT_PROCESS 0x01 /* process controls switching */
The vt_mode structure will be filled in with the current
value for each field.
VT_RELDISP
Used to tell the virtual terminal manager that the
display has or has not been released by the process.
0 == release refused
1 == release acknowledged
2 == acquire acknowledged
VT_ACTIVATE
Makes the multiscreen number specified in the argument
the active multiscreen. The video driver will cause a
switch to occur in the same manner as if a hotkey
sequence had been typed at the keyboard. If the
specified multiscreen is not open or does not exist,
the call will fail and errno will be set to ENXIO.
Graphics Adapter Port I/O
You can use ioctl(S) to read or write a byte from or to the
graphics adapter port. The arg parameter of the ioctl call
uses the io_arg data structure:
struct port_io_arg {
struct port_io_struct args[4];
};
As shown above, the io_arg structure points to an array of
four port_io data structures. The port_io structure has the
following format:
struct port_io_struct {
char dir; /* direction flag (in vs. out) */
unsigned short port; /* port address */
char data; /* byte of data */
};
You may specify one, two, three, or four of the
port_io_struct structures in the array for one ioctl call.
The value of dir can be either IN_ON_PORT to specify a byte
being input to the graphics adapter port or OUT_ON_PORT to
specify a byte being output to the graphics adapter port.
Port is an integer specifying the port address of the
desired graphics adapter port. Data is the byte of data
being input or output as specified by the call.
If you are not using any of the port_io structures, load the
port with 0, and leave the unused structures at the end of
Page 11 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
the array. Refer to the hardware manuals for port addresses
and functions for the various adapters.
You can use the following ioctl(S) commands to input or
output a byte on the graphics adapter port:
CONSIO Inputs or outputs a byte on the
current graphics adapter port as
specified. (All)
MGAIO Inputs or outputs a byte on the
monochrome adapter port as
specified. (MONO only)
CGAIO Inputs or outputs a byte on the
color graphics adapter port as
specified. (CGA only)
EGAIO Inputs or outputs a byte on the
enhanced graphics adapter port as
specified. (EGA only)
VGAIO Inputs or outputs a byte on the
video graphics array adapter port
as specified. (VGA only)
To input a byte on any of the graphics adapter ports, load
dir with IN_ON_PORT and load port with the port address of
the graphics adapter. The byte input from the graphics
adapter port will be returned in data.
To output a byte, load dir with OUT_ON_PORT, load port with
the port address of the graphics adapter, and load data with
the byte you want output to the graphics adapter port.
Function Keys
ioctl(S) can be used to define or obtain the current
definition of a function key. The arg parameter of the
ioctl call uses the fkeyarg data structure:
struct fkeyarg {
unassigned int keynum;
char keydef [MAXFK];
/* Comes from
char flen; ioctl.h via comcrt.h */
}
You can use the following ioctl(S) requests to obtain or
assign function key definitions:
Page 12 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
GETFKEY Obtains the current definition of a
function key. The function key
number must be passed in keynum.
The string currently assigned to
the key will be returned in keydef
and the length of the string will
be returned in flen when the ioctl
is performed.
SETFKEY Assigns a given string to a
function key. The function key
number must be passed in keydef and
the length of the string (number of
characters) must be passed in flen.
SETLOCKLOCK Toggles the <Caps Lock> and <Num
Lock> keys to be either global to
all the multiscreens, or local to
each individual multiscreen. To
make the <Caps Lock> global (its
default), set the arg parameter to
1. To make the <Caps Lock> local
to each screen, set the arg
parameter to 0.
ANSI Screen Attribute Sequences
The following character sequences are defined by ANSI
X3.64-1979 and may be used to control and modify the screen
display. Each n is replaced by the appropriate ASCII number
(decimal) to produce the desired effect. The last column is
for termcap(M) codes, where ``n/a'' means not applicable.
The use of 7 or 8 bit characters in the escape sequence is a
valid invocation for each action defined. For example the
ANSI ED command can be invoked via the ``ESC[n J'' (0x1b-
0x5b-n-0x4a, 7 bit chars) sequence or the ``CSInJ'' (0x9b-
n-0x4n, 8 bit chars) sequence.
ISO Sequence Action Termcap
Code
_________________________________________________________________
ED CSInJ Erases all or part cd
(Erase in of a display. n=0:
Display) erases from active
position to end of
display. n=1:
erases from the
beginning of display
to active position.
n=2: erases entire
Page 13 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
display.
EL CSInK Erases all or part ce
(Erase in of a line. n=0:
Line) erases from active
position to end of
line. n=1: erases
from beginning of
line to active
position. n=2:
erases entire line.
ECH CSInX Erases n characters n/a
(Erase
Character)
CBT CSInZ Moves active bt
(Cursor position back n tab
Backward stops.
Tabulation)
SU CSInS Scroll screen up n sf
(Scroll lines, introducing
Up) new blank lines at
bottom.
SD CSInT Scrolls screen down sr
(Scroll n lines, introducing
Down) new blank lines at
top.
CUP CSIm;nH Moves active cm
(Cursor position to location
Position) m (vertical) and n
(horizontal).
HVP CSIm;nf Moves active n/a
(Horizontal position to location
& Vertical m (vertical) and n
Position) (horizontal).
CUU CSInA Moves active up (ku)
(Cursor Up) position up n number
of lines.
CUD CSInB Moves active do (kd)
(Cursor position down n num-
Down) ber of lines.
CUF
(Cursor
Forward)
Page 14 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
CSInC
Moves active nd (kr)
Page 15 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
position n spaces to
the right.
CUB CSInD Moves active bs (kl)
(Cursor position n spaces
Backward) backward.
HPA CSIn` Moves active n/a
(Horizontal position to column
Position given by n.
Absolute)
HPR CSIna Moves active n/a
(Horizontal position n
Position characters to the
Relative) right.
VPA CSInd Moves active n/a
(Vertical position to line
Position given by n.
Absolute)
VPR CSIne Moves active n/a
(Vertical position down n num-
Position ber of lines.
Relative)
IL CSInL Inserts n new, blank al
(Insert lines.
Line)
ICH CSIn@ Inserts n blank ic
(Insert places for n
Character) characters.
DL CSInM Deletes n lines. dl
(Delete
Line)
DCH CSInP Deletes n number of dc
(Delete characters.
Character)
CPL CSInF Moves active n/a
(Cursor to position to
Previous beginning of line, n
Line) lines up.
Page 16 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
CNL CSInE Moves active n/a
(Cursor position to
Next beginning of line, n
Line) lines down.
SGR CSInm Character n/a
(Select attributes, as
Graphic summarized in the
Rendition) chart below. Up to
three attributes can
be specified in the
form: CSI n1; n2;
n3 m
_________________________________________________
| Select Graphic Rendition (SGR) Chart |
|________________________________________________|
| n Meaning |
|________________________________________________|
| 0 all attributes off (normal display) |
| 1 bold intensity (or light color) |
| 4 underscore on (if hardware supports it)|
| 5 blink on (if hardware supports it) |
| 7 reverse video |
| 8 sets blank (non-display) |
| 10 selects the primary font |
| 11 selects the first alternate font; lets |
| ASCII characters less than 32 be |
| displayed as ROM characters |
| 12 selects a second alternate font; |
| toggles high bit of extended ASCII code|
| before displaying as ROM characters |
| 30 black foreground |
| 31 red foreground |
| 32 green foreground |
| 33 brown foreground |
| 34 blue foreground |
| 35 magenta foreground |
| 36 cyan foreground |
| 37 white foreground |
| 38 enables underline option; white |
| foreground with white underscore |
| 39 disables underline option |
| 40 black background |
| 41 red background |
| 42 green background |
| 43 brown background |
| 44 blue background |
|________________________________________________|
Page 17 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
| 45 magenta background |
| 46 cyan background |
| 47 white background |
|________________________________________________|
ISO Sequence Action Termcap
Code
_________________________________________________________________
SM CSI2h Lock keyboard. n/a
(Set Mode) Ignores keyboard
input until
unlocked.
Characters are not
saved.
MC CSI2i Send screen to host. n/a
(Media Current screen
Copy) contents are sent to
the application.
RM CSI2l Unlock keyboard. n/a
(Reset Re-enable keyboard
Mode) input.
Additional Screen Attribute Sequences
Termcap
Name Sequence Action Code
_________________________________________________________________
n/a CSI=p;dB Set the bell parameter to n/a
the decimal values of p
and d. p is the period
of the bell tone in units
of 840.3 nanoseconds, and
d is the duration of the
tone in units of 100
milliseconds.
n/a CSI=s;eC Set the cursor to start n/a
on scanline s and end on
scanline e.
n/a CSI=xD Turn on or off (x=1 or 0) n/a
the intensity of the
background color.
Page 18 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
n/a CSI=xE Set or clear (x=1 or 0) n/a
the Blink vs. Bold
background bit in the
6845 crt controller.
n/a CSI=cA Set overscan color to n/a
color c. c is a decimal
value taken from Color
Table above. (This
sequence may not be
supported on all
hardware.)
n/a CSI=cF Set normal foreground n/a
color to c. (c is a
decimal parameter taken
from Color Table.)
n/a CSI=cG Set normal background. n/a
(See Color Table.)
n/a CSI=c H Set reverse foreground. n/a
(See Color Table.)
n/a CSI=c I Set reverse background. n/a
(See Color Table.)
n/a CSI=c J Set graphic foreground. n/a
(See Color Table.)
n/a CSI=c K Set graphic background. n/a
(See Color Table.)
_________________________________
| Color Table |
|___|_________|____|_____________|
| Cn| Color | Cn| Color |
|___|_________|____|_____________|
| 0 | Black | 8| Grey |
| 1 | Blue | 9| Lt. Blue |
| 2 | Green | 10| Lt. Green |
| 3 | Cyan | 11| Lt. Cyan |
| 4 | Red | 12| Lt. Red |
| 5 | Magenta| 13| Lt. Magenta|
| 6 | Brown | 14| Yellow |
| 7 | White | 15| Lt. White |
|___|_________|____|_____________|
Termcap
Page 19 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
Name Sequence Action Code
_________________________________________________________________
n/a CSIng Accesses alternate n/a
graphics set. Not the
same as
``graphics mode.'' Refer
to your owner's manual
for decimal/character
codes (Pn) and possible
output characters.
n/a CSInL Fills new regions with n/a
current (n=0) or normal
(n=1) attributes.
Default is 0.
n/a CSInM Returns current n/a
foreground color
attributes, with n=0 for
normal, 1 for reverse,
and 2 for graphic. The
colors are sent back in
the keyboard data input
stream as text decimal
values separated by a
space and terminated with
a newline. For example,
if the current foreground
color is lt_red on black,
``12 0\n'' is returned.
n/a CSIs Saves current cursor n/a
position.
n/a CSIu Restores saved cursor n/a
position.
n/a ESC7 Saves current cursor n/a
position.
n/a ESC8 Restores saved cursor n/a
position.
n/a ESCQFn'string' Define function key Fn n/a
with string. String
delimiters ' and ' may be
any character not in
string. Fn is defined as
the key number starting
Page 20 (printed 2/19/91)
SCREEN(HW) XENIX System V SCREEN(HW)
at zero plus the ASCII
value of zero. For
example, F1 = 0... F16 =
?, and so on.
In this escape sequence,
the ^ character will
cause the next character
to have 32 subtracted
from its ASCII value.
Thus ^! results in a soh
(^A) characters.
n/a CSInz Switches to screen n. If n/a
the screen does not
exist, no action will
take place.
Files
/dev/console
/dev/tty[02 -n]
/dev/color
/dev/monochrome
/dev/ega
/dev/vga
See Also
console(M), ioctl(S), keyboard(HW), keymap(M), mapkey(M),
mapchan(M), multiscreen(M), setcolor(C), stty(C), systty(M),
vidi(C), termcap(M), tty(M)
Page 21 (printed 2/19/91)
