e2image man page on SuSE

Printed from http://www.polarhome.com/service/man/?qf=e2image&af=0&tf=2&of=SuSE

E2IMAGE(8)							    E2IMAGE(8)

NAME
       e2image - Save critical ext2/ext3/ext4 filesystem metadata to a file

SYNOPSIS
       e2image [ -rsI ] device image-file

DESCRIPTION
       The  e2image  program will save critical ext2, ext3, or ext4 filesystem
       metadata located on device to a	file  specified	 by  image-file.   The
       image  file  may	 be  examined by dumpe2fs and debugfs, by using the -i
       option to those programs.  This can assist an expert in recovering cat‐
       astrophically  corrupted	 filesystems.	In  the future, e2fsck will be
       enhanced to be able to use the image file to help recover a badly  dam‐
       aged filesystem.

       If image-file is -, then the output of e2image will be sent to standard
       output, so that the output can be piped to  another  program,  such  as
       gzip(1).	  (Note	 that this is currently only supported when creating a
       raw image file using the -r option, since the  process  of  creating  a
       normal  image  file currently requires random access to the file, which
       cannot be done using a pipe.  This restriction will hopefully be lifted
       in a future version of e2image.)

       It  is a very good idea to create image files for all of filesystems on
       a system and save the partition layout (which can  be  generated	 using
       the  fdisk  -l  command)	 at regular intervals --- at boot time, and/or
       every week or so.  The image file should be stored on  some  filesystem
       other  than  the filesystem whose data it contains, to ensure that this
       data is accessible in the case where the filesystem has been badly dam‐
       aged.

       To  save	 disk  space, e2image creates the image file as a sparse file.
       Hence, if the image file needs to be copied  to	another	 location,  it
       should  either  be compressed first or copied using the --sparse=always
       option to the GNU version of cp.

       The size of an ext2 image file depends primarily on  the	 size  of  the
       filesystems  and how many inodes are in use.  For a typical 10 gigabyte
       filesystem, with 200,000 inodes in use out of 1.2 million  inodes,  the
       image  file will be approximately 35 megabytes; a 4 gigabyte filesystem
       with 15,000 inodes in use out of 550,000 inodes	will  result  in  a  3
       megabyte	 image	file.	Image  files tend to be quite compressible; an
       image file taking up 32 megabytes of space on disk will generally  com‐
       press down to 3 or 4 megabytes.

RESTORING FILESYSTEM METADATA USING AN IMAGE FILE
       The  -I option will cause e2image to install the metadata stored in the
       image file back to the  device.	   It  can  be	used  to  restore  the
       filesystem metadata back to the device in emergency situations.

       WARNING!!!!  The -I option should only be used as a desperation measure
       when other alternatives have failed.  If	 the  filesystem  has  changed
       since  the  image file was created, data will be lost.  In general, you
       should make a full image backup of the filesystem first,	 in  case  you
       wish to try other recovery strategies afterwards.

RAW IMAGE FILES
       The  -r	option	will create a raw image file instead of a normal image
       file.  A raw image file differs from a normal image file in  two	 ways.
       First, the filesystem metadata is placed in the proper position so that
       e2fsck, dumpe2fs, debugfs, etc. can be run directly on  the  raw	 image
       file.   In order to minimize the amount of disk space consumed by a raw
       image file, the file is created as a sparse file.  (Beware  of  copying
       or compressing/decompressing this file with utilities that don't under‐
       stand how to create sparse files; the file will become as large as  the
       filesystem  itself!)   Secondly, the raw image file also includes indi‐
       rect blocks and directory blocks, which the standard  image  file  does
       not have, although this may change in the future.

       Raw  image  files  are  sometimes  used when sending filesystems to the
       maintainer as part of bug reports to  e2fsprogs.	  When	used  in  this
       capacity,  the recommended command is as follows (replace hda1 with the
       appropriate device):

	    e2image -r /dev/hda1 - | bzip2 > hda1.e2i.bz2

       This will only send the metadata information, without any data  blocks.
       However,	 the filenames in the directory blocks can still reveal infor‐
       mation about the contents of the filesystem that the bug	 reporter  may
       wish  to keep confidential.  To address this concern, the -s option can
       be specified.  This will cause e2image to  scramble  directory  entries
       and zero out any unused portions of the directory blocks before writing
       the image file.	However, the -s option will prevent analysis of	 prob‐
       lems related to hash-tree indexed directories.

AUTHOR
       e2image was written by Theodore Ts'o (tytso@mit.edu).

AVAILABILITY
       e2image	is  part  of  the  e2fsprogs  package  and  is	available from
       http://e2fsprogs.sourceforge.net.

SEE ALSO
       dumpe2fs(8), debugfs(8)

E2fsprogs version 1.41.9	  August 2009			    E2IMAGE(8)
[top]

List of man pages available for SuSE

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net