SETTERM(1) User Commands SETTERM(1)NAMEsetterm - set terminal attributes
SYNOPSISsetterm [options]
DESCRIPTIONsetterm writes to standard output a character string that will invoke
the specified terminal capabilities. Where possible terminfo is con‐
sulted to find the string to use. Some options however (marked "vir‐
tual consoles only" below) do not correspond to a terminfo(5) capabil‐
ity. In this case, if the terminal type is "con" or "linux" the string
that invokes the specified capabilities on the PC Minix virtual console
driver is output. Options that are not implemented by the terminal are
ignored.
OPTIONS
For boolean options (on or off), the default is on.
For conciseness, an 8-color below is black, red, green, yellow, blue,
magenta, cyan, or white.
A 16-color is an 8-color, grey, or bright followed by red, green, yel‐
low, blue, magenta, cyan, or white.
The various color options may be set independently, at least at virtual
consoles, though the results of setting multiple modes (for example,
-underline and -half-bright) are hardware-dependent.
-appcursorkeys [on|off] (virtual consoles only)
Sets Cursor Key Application Mode on or off. When on, ESC O A,
ESC O B, etc. will be sent for the cursor keys instead of ESC [
A, ESC [ B, etc. See the "vi and Cursor-Keys" section of the
Text-Terminal-HOWTO for how this can cause problems for vi
users.
-append [1-NR_CONS]
Like -dump, but appends to the snapshot file instead of over‐
writing it. Only works if no -dump options are given.
-background 8-color|default (virtual consoles only)
Sets the background text color.
-blank [0-60|force|poke] (virtual consoles only)
Sets the interval of inactivity, in minutes, after which the
screen will be automatically blanked (using APM if available).
Without an argument, gets the blank status (returns which vt was
blanked or zero for unblanked vt).
The force option keeps screen blank even if a key is pressed.
The poke option unblank the screen.
-bfreq [freqnumber]
Sets the bell frequency in Hz. Without an argument, defaults to
0.
-blength [0-2000]
Sets the bell duration in milliseconds. Without an argument,
defaults to 0.
-blink [on|off]
Turns blink mode on or off. Except at a virtual console, -blink
off turns off all attributes (bold, half-brightness, blink,
reverse).
-bold [on|off]
Turns bold (extra bright) mode on or off. Except at a virtual
console, -bold off turns off all attributes (bold, half-bright‐
ness, blink, reverse).
-clear [all]
Clears the screen and "homes" the cursor, as clear(1).
-clear rest
Clears from the current cursor position to the end of the
screen.
-clrtabs [tab1 tab2 tab3 ...] (virtual consoles only)
Clears tab stops from the given horizontal cursor positions, in
the range 1-160. Without arguments, clears all tab stops.
-cursor [on|off]
Turns the terminal's cursor on or off.
-default
Sets the terminal's rendering options to the default values.
-dump [1-NR_CONS]
Writes a snapshot of the given virtual console (with attributes)
to the file specified in the -file option, overwriting its con‐
tents; the default is screen.dump. Without an argument, dumps
the current virtual console. Overrides -append.
-append [1-NR_CONS]
Like -dump, but appends to the snapshot file instead of over‐
writing it. Only works if no -dump options are given.
-file dumpfilename
Sets the snapshot file name for any -dump or -append options on
the same command line. If this option is not present, the
default is screen.dump in the current directory. A path name
that exceeds system maximum will be truncated, see PATH_MAX from
linux/limits.h for the value.
-msg [on|off] (virtual consoles only)
Enables or disables the sending of kernel printk() messages to
the console.
-msglevel 1-8 (virtual consoles only)
Sets the console logging level for kernel printk() messages.
All messages strictly more important than this will be printed,
so a logging level of 0 has the same effect as -msg on and a
logging level of 8 will print all kernel messages. klogd(8) may
be a more convenient interface to the logging of kernel mes‐
sages.
-powerdown [0-60]
Sets the VESA powerdown interval in minutes. Without an argu‐
ment, defaults to 0 (disable powerdown). If the console is
blanked or the monitor is in suspend mode, then the monitor will
go into vsync suspend mode or powerdown mode respectively after
this period of time has elapsed.
-underline [on|off]
Turns underline mode on or off (see -ulcolor).
-powersave [off]
Turns off monitor VESA powersaving features.
-powersave on|vsync
Puts the monitor into VESA vsync suspend mode.
-powersave powerdown
Puts the monitor into VESA powerdown mode.
-powersave hsync
Puts the monitor into VESA hsync suspend mode.
-regtabs [1-160] (virtual consoles only)
Clears all tab stops, then sets a regular tab stop pattern, with
one tab every specified number of positions. Without an argu‐
ment, defaults to 8.
-repeat [on|off] (virtual consoles only)
Turns keyboard repeat on or off.
-reset Displays the terminal reset string, which typically resets the
terminal to its power on state.
-reverse [on|off]
Turns reverse video mode on or off. Except at a virtual con‐
sole, -reverse off turns off all attributes (bold, half-bright‐
ness, blink, reverse).
-store (virtual consoles only)
Stores the terminal's current rendering options (foreground and
background colors) as the values to be used at reset-to-default.
-tabs [tab1 tab2 tab3 ...] (virtual consoles only)
Sets tab stops at the given horizontal cursor positions, in the
range 1-160. Without arguments, shows the current tab stop set‐
tings.
-term terminal_name
Overrides the TERM environment variable.
-ulcolor 16-color (virtual consoles only)
Sets the color for underlined characters.
-version
Output version information and exit.
-help Output help screen and exit.
SEE ALSOtput(1), stty(1), terminfo(5), tty(4)BUGS
Differences between the Minix and Linux versions are not documented.
AVAILABILITY
The setterm command is part of the util-linux package and is available
from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux January 2000 SETTERM(1)
