INET6(4) OpenBSD Programmer's Manual INET6(4)NAMEinet6 - Internet protocol version 6 family
SYNOPSIS
#include <sys/types.h>
#include <netinet/in.h>
DESCRIPTION
The inet6 family is an updated version of the inet(4) family. While
inet(4) implements Internet Protocol version 4, inet6 implements Internet
Protocol version 6.
inet6 is a collection of protocols layered atop the Internet Protocol
version 6 (IPv6) transport layer, and utilizing the IPv6 address format.
The inet6 family provides protocol support for the SOCK_STREAM,
SOCK_DGRAM, and SOCK_RAW socket types; the SOCK_RAW interface provides
access to the IPv6 protocol.
ADDRESSING
IPv6 addresses are 16 byte quantities, stored in network standard
byteorder. The include file <netinet/in.h> defines this address as a
discriminated union.
Sockets bound to the inet6 family utilize the following addressing
structure:
struct sockaddr_in6 {
u_int8_t sin6_len;
sa_family_t sin6_family;
in_port_t sin6_port;
u_int32_t sin6_flowinfo;
struct in6_addr sin6_addr;
u_int32_t sin6_scope_id;
};
Sockets may be created with the local address ``::'' (which is equal to
IPv6 address 0:0:0:0:0:0:0:0) to effect ``wildcard'' matching on incoming
messages.
The IPv6 specification defines scoped address, like link-local or site-
local address. A scoped address is ambiguous to the kernel, if it is
specified without a scope identifier. To manipulate scoped addresses
properly from userland, programs must use the advanced API defined in RFC
2292. A compact description of the advanced API is available in ip6(4).
If scoped addresses are specified without explicit scope, the kernel may
raise an error. Note that scoped addresses are not for daily use at this
moment, both from a specification and an implementation point of view.
KAME implementation supports extended numeric IPv6 address notation for
link-local addresses, like ``fe80::1%de0'' to specify ``fe80::1 on de0
interface''. The notation is supported by getaddrinfo(3) and
getnameinfo(3). Some normal userland programs, such as telnet(1) or
ftp(1), are able to use the notation. With special programs like
ping6(8), an outgoing interface can be specified with an extra command
line option to disambiguate scoped addresses.
Scoped addresses are handled specially in the kernel. In the kernel
structures like routing tables or interface structure, scoped addresses
will have their interface index embedded into the address. Therefore,
the address on some of the kernel structure is not the same as that on
the wire. The embedded index will become visible on PF_ROUTE socket,
kernel memory accesses via kvm(3) and some other occasions. HOWEVER,
users should never use the embedded form. For details please consult
http://www.kame.net/dev/cvsweb2.cgi/kame/IMPLEMENTATION. Note that the
above URL describes the situation with the latest KAME tree, not the
OpenBSD tree.
PROTOCOLS
The inet6 family is comprised of the IPv6 network protocol, Internet
Control Message Protocol version 6 (ICMPv6), Transmission Control
Protocol (TCP), and User Datagram Protocol (UDP). TCP is used to support
the SOCK_STREAM abstraction while UDP is used to support the SOCK_DGRAM
abstraction. Note that TCP and UDP are common to inet(4) and inet6. A
raw interface to IPv6 is available by creating an Internet socket of type
SOCK_RAW. The ICMPv6 message protocol is accessible from a raw socket.
Interaction between IPv4/v6 sockets
OpenBSD does not route IPv4 traffic to an AF_INET6 socket, for security
reasons. If both IPv4 and IPv6 traffic need to be accepted, listen on
two sockets.
The behavior of AF_INET6 TCP/UDP socket is documented in RFC 2553.
Basically, it says the following:
o A specific bind to an AF_INET6 socket (bind(2) with address
specified) should accept IPv6 traffic to that address only.
o If a wildcard bind is performed on an AF_INET6 socket (bind(2) to
IPv6 address ::), and there is no wildcard bind AF_INET socket on
that TCP/UDP port, IPv6 traffic as well as IPv4 traffic should be
routed to that AF_INET6 socket. IPv4 traffic should be seen as if it
came from IPv6 address like ::ffff:10.1.1.1. This is called IPv4
mapped address.
o If there are both wildcard bind AF_INET socket and wildcard bind
AF_INET6 socket on one TCP/UDP port, they should behave separately.
IPv4 traffic should be routed to AF_INET socket and IPv6 should be
routed to AF_INET6 socket.
However, RFC 2553 does not define the constraint between the order of
bind(2), nor how IPv4 TCP/UDP port numbers and IPv6 TCP/UDP port numbers
relate to each other (should they be integrated or separated).
Implemented behavior is very different from kernel to kernel. Therefore,
it is unwise to rely too much upon the behavior of AF_INET6 wildcard bind
socket. It is recommended to listen to two sockets, one for AF_INET and
another for AF_INET6, if both IPv4 and IPv6 traffic are to be accepted.
It should also be noted that malicious parties can take advantage of the
complexity presented above, and are able to bypass access control, if the
target node routes IPv4 traffic to AF_INET6 socket. Caution should be
taken when handling connections from IPv4 mapped addresses to AF_INET6
sockets.
SEE ALSOioctl(2), socket(2), sysctl(3), icmp6(4), intro(4), ip6(4), tcp(4),
udp(4)STANDARDS
Tatsuya Jinmei and Atsushi Onoe, An Extension of Format for IPv6 Scoped
Addresses, internet draft, draft-ietf-ipngwg-scopedaddr-format-02.txt,
June 2000, work in progress material.
HISTORY
The inet6 protocol interface is defined in RFC 2553 and RFC 2292. The
implementation described herein appeared in WIDE/KAME project.
BUGS
The IPv6 support is subject to change as the Internet protocols develop.
Users should not depend on details of the current implementation, but
rather the services exported.
``Version independent'' code should be implemented as much as possible in
order to support both inet(4) and inet6.
OpenBSD 4.9 December 13, 2009 OpenBSD 4.9