IPMI-SENSORS man page on Oracle
[printable version]
/* Copyright (C) 1991‐2012 Free Software Foundation, Inc.
This file is part of the GNU C Library.
The GNU C Library is free software; you can redistribute it
and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later ver‐
sion.
The GNU C Library is distributed in the hope that it will be
useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU
Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Pub‐
lic
License along with the GNU C Library; if not, see
<http://www.gnu.org/licenses/>. */ /* This header is separate
from features.h so that the compiler can
include it implicitly at the start of every compilation. It
must
not itself include <features.h> or any other header that in‐
cludes
<features.h> because the implicit include comes before any
feature
test macros that may be defined in a source file before it
first
explicitly includes a system header. GCC knows the name of
this
header in order to preinclude it. */ /* We do support the IEC
559 math functionality, real and complex. */ /* wchar_t uses
ISO/IEC 10646 (2nd ed., published 2011‐03‐15) /
IPMI-SENSORS(8) System Commands IPMI-SENSORS(8)
Unicode 6.0. */ /* We do not support C11 <threads.h>. */
NAME
ipmi-sensors - display IPMI sensor information
SYNOPSIS
ipmi-sensors [OPTION...]
DESCRIPTION
Ipmi-sensors displays current readings of sensors and sensor data
repository (SDR) information. The default display outputs each sensor's
record id, sensor name, sensor type name, sensor reading (if appropri‐
ate), and the current sensor event. More verbose information can be
found using the verbose options specified below. Ipmi-sensors does not
inform the user if a problem exists with a particular sensor because
sensor readings and events are not analyzed by default. Users may wish
to use the --output-sensor-state option to output the analyzed sensor
state. Some sensors may have a sensor reading or sensor event of "N/A"
if the information is unavailable. This is typical of a sensor that is
not enabled or not owned by a BMC. Please see --bridge-sensors option
below to deal with sensors not owned by a BMC. Sensors may output a
sensor event of "Unknown" if the sensor reading cannot be read. This is
typical of a sensor that is busy or a reading that cannot be calcu‐
lated. If sensors report "Unrecognized State", it is indicative of an
unkown sensor type, typically an OEM sensor. If the sensor OEM inter‐
pretation is available, the --interpret-oem-data may be able to report
the appropriate sensor state. Sensors need not always report a sensor
event. When a sensor event is not present, "OK" is typically reported.
Listed below are general IPMI options, tool specific options, trouble
shooting information, workaround information, examples, and known
issues. For a general introduction to FreeIPMI please see freeipmi(7).
To perform IPMI sensor configuration, please see ipmi-sensors-con‐
fig(8). To perform some advanced SDR management, please see bmc-
device(8).
GENERAL OPTIONS
The following options are general options for configuring IPMI communi‐
cation and executing general tool commands.
-D IPMIDRIVER, --driver-type=IPMIDRIVER
Specify the driver type to use instead of doing an auto selec‐
tion. The currently available outofband drivers are LAN and
LAN_2_0, which perform IPMI 1.5 and IPMI 2.0 respectively. The
currently available inband drivers are KCS, SSIF, OPENIPMI, and
SUNBMC.
--disable-auto-probe
Do not probe in-band IPMI devices for default settings.
--driver-address=DRIVER-ADDRESS
Specify the in-band driver address to be used instead of the
probed value. DRIVER-ADDRESS should be prefixed with "0x" for a
hex value and '0' for an octal value.
--driver-device=DEVICE
Specify the in-band driver device path to be used instead of the
probed path.
--register-spacing=REGISTER-SPACING
Specify the in-band driver register spacing instead of the
probed value. Argument is in bytes (i.e. 32bit register spacing
= 4)
--target-channel-number=CHANNEL-NUMBER
Specify the in-band driver target channel number to send IPMI
requests to.
--target-slave-address=SLAVE-ADDRESS
Specify the in-band driver target slave number to send IPMI
requests to.
-h IPMIHOST1,IPMIHOST2,..., --hostname=IPMIHOST1[:PORT],IPMI‐
HOST2[:PORT],...
Specify the remote host(s) to communicate with. Multiple host‐
names may be separated by comma or may be specified in a range
format; see HOSTRANGED SUPPORT below. An optional port can be
specified with each host, which may be useful in port forwarding
or similar situations.
-u USERNAME, --username=USERNAME
Specify the username to use when authenticating with the remote
host. If not specified, a null (i.e. anonymous) username is
assumed. The user must have atleast OPERATOR privileges in order
for this tool to operate fully.
-p PASSWORD, --password=PASSWORD
Specify the password to use when authenticationg with the remote
host. If not specified, a null password is assumed. Maximum
password length is 16 for IPMI 1.5 and 20 for IPMI 2.0.
-P, --password-prompt
Prompt for password to avoid possibility of listing it in
process lists.
-k K_G, --k-g=K_G
Specify the K_g BMC key to use when authenticating with the
remote host for IPMI 2.0. If not specified, a null key is
assumed. To input the key in hexadecimal form, prefix the string
with '0x'. E.g., the key 'abc' can be entered with the either
the string 'abc' or the string '0x616263'
-K, --k-g-prompt
Prompt for k-g to avoid possibility of listing it in process
lists.
--session-timeout=MILLISECONDS
Specify the session timeout in milliseconds. Defaults to 20000
milliseconds (20 seconds) if not specified.
--retransmission-timeout=MILLISECONDS
Specify the packet retransmission timeout in milliseconds.
Defaults to 1000 milliseconds (1 second) if not specified. The
retransmission timeout cannot be larger than the session time‐
out.
-a AUTHENTICATION-TYPE, --authentication-type=AUTHENTICATION-TYPE
Specify the IPMI 1.5 authentication type to use. The currently
available authentication types are NONE, STRAIGHT_PASSWORD_KEY,
MD2, and MD5. Defaults to MD5 if not specified.
-I CIPHER-SUITE-ID, --cipher-suite-id=CIPHER-SUITE-ID
Specify the IPMI 2.0 cipher suite ID to use. The Cipher Suite ID
identifies a set of authentication, integrity, and confidential‐
ity algorithms to use for IPMI 2.0 communication. The authenti‐
cation algorithm identifies the algorithm to use for session
setup, the integrity algorithm identifies the algorithm to use
for session packet signatures, and the confidentiality algorithm
identifies the algorithm to use for payload encryption. Defaults
to cipher suite ID 3 if not specified. The following cipher
suite ids are currently supported:
0 - Authentication Algorithm = None; Integrity Algorithm = None;
Confidentiality Algorithm = None
1 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm =
None; Confidentiality Algorithm = None
2 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm =
HMAC-SHA1-96; Confidentiality Algorithm = None
3 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm =
HMAC-SHA1-96; Confidentiality Algorithm = AES-CBC-128
6 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
None; Confidentiality Algorithm = None
7 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
HMAC-MD5-128; Confidentiality Algorithm = None
8 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
HMAC-MD5-128; Confidentiality Algorithm = AES-CBC-128
11 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
MD5-128; Confidentiality Algorithm = None
12 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
MD5-128; Confidentiality Algorithm = AES-CBC-128
15 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm
= None; Confidentiality Algorithm = None
16 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm
= HMAC_SHA256_128; Confidentiality Algorithm = None
17 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm
= HMAC_SHA256_128; Confidentiality Algorithm = AES-CBC-128
-l PRIVILEGE-LEVEL, --privilege-level=PRIVILEGE-LEVEL
Specify the privilege level to be used. The currently available
privilege levels are USER, OPERATOR, and ADMIN. Defaults to
OPERATOR if not specified.
--config-file=FILE
Specify an alternate configuration file.
-W WORKAROUNDS, --workaround-flags=WORKAROUNDS
Specify workarounds to vendor compliance issues. Multiple work‐
arounds can be specified separated by commas. A special command
line flag of "none", will indicate no workarounds (may be useful
for overriding configured defaults). See WORKAROUNDS below for a
list of available workarounds.
--debug
Turn on debugging.
-?, --help
Output a help list and exit.
--usage
Output a usage message and exit.
-V, --version
Output the program version and exit.
IPMI-SENSORS OPTIONS
The following options are specific to Ipmi-sensors.
-v, --verbose
Output verbose sensor output. This option will output additional
information about sensors such as thresholds, ranges, numbers,
and event/reading type codes.
-vv Output very verbose sensor output. This option will output more
additional information than the verbose option such as informa‐
tion about events, other sensor types, and oem sensors.
-i, --sdr-info
Show sensor data repository (SDR) information
-q, --quiet-readings
Do not output sensor reading values by default. This option is
particularly useful if you want to use hostranged output across
a cluster and want to consolidate the output.
-r RECORD-IDS-LIST, --record-ids=RECORD-IDS-LIST
Specify sensors to show by record id. Multiple record ids can be
separated by commas or spaces. If both --record-ids and --sen‐
sor-types are specified, --record-ids takes precedence. A spe‐
cial command line record id of "all", will indicate all record
ids should be shown (may be useful for overriding configured
defaults).
-R RECORD-IDS-LIST, --exclude-record-ids=RECORD-IDS-LIST
Specify sensors to not show by record id. Multiple record ids
can be separated by commas or spaces. A special command line
record id of "none", will indicate no record ids should be
excluded (may be useful for overriding configured defaults).
-t SENSOR-TYPE-LIST, --sensor-types=SENSOR-TYPE-LIST
Specify sensor types to show outputs for. Multiple types can be
separated by commas or spaces. If both --record-ids and --sen‐
sor-types are specified, --record-ids takes precedence. A spe‐
cial command line type of "all", will indicate all types should
be shown (may be useful for overriding configured defaults).
Users may specify sensor types by string (see --list-sen‐
sor-types below) or by number (decimal or hex).
-T SENSOR-TYPE-LIST, --exclude-sensor-types=SENSOR-TYPE-LIST
Specify sensor types to not show outputs for. Multiple types can
be eparated by commas or spaces. A special command line type of
"none", will indicate no types should be excluded (may be useful
for overriding configured defaults). Users may specify sensor
types by string (see --list-sensor-types below) or by number
(decimal or hex).
-L, --list-sensor-types
List sensor types.
-b, --bridge-sensors
By default, sensors readings are not attempted for sensors on
non-BMC owners. By setting this option, sensor requests can be
bridged to non-BMC owners to obtain sensor readings. Bridging
may not work on some interfaces/driver types.
--shared-sensors
Some sensors share the same sensor data record (SDR). This is
typically utilized for system event log (SEL) entries and not
for sensor readings. However, there may be some motherboards in
which this format is utilized for multiple active sensors, or
the user simply has interest in seeing the permutation of
entries shared by a SDR entry. By setting this option, each sen‐
sor number shared by a record will be iterated over and output.
--interpret-oem-data
Attempt to interpret OEM data, such as event data, sensor read‐
ings, or general extra info, etc. If an OEM interpretation is
not available, the default output will be generated. Correctness
of OEM interpretations cannot be guaranteed due to potential
changes OEM vendors may make in products, firmware, etc. See OEM
INTERPRETATION below for confirmed supported motherboard inter‐
pretations.
--ignore-not-available-sensors
Ignore not-available (i.e. N/A) sensors in output.
--ignore-unrecognized-events
Ignore unrecognized sensor events. This will suppress output of
unrecognized events, typically shown as 'Unrecognized Event =
XXXXh' in output. In addition, unrecognized events will be
ignored when calculating sensor state with --output-sensor-state
below.
--output-event-bitmask
Output event bitmask value instead of the string representation.
--output-sensor-state
Output sensor state in output. This will add an additional out‐
put reporting if a sensor is in a NOMINAL, WARNING, or CRITICAL
state. The sensor state is an interpreted value based on the
current sensor event. The sensor state interpretations are
determined by the configuration file
/etc/freeipmi//freeipmi_interpret_sensor.conf. See
freeipmi_interpret_sensor.conf(5) for more information. This
option gives identical output to the sensor state previously
output by ipmimonitoring(8).
--sensor-state-config-file=FILE
Specify an alternate sensor state configuration file. Option
ignored if --output-sensor-state not specified.
--entity-sensor-names
Output sensor names prefixed with their entity id and instance
number when appropriate. This may be necessary on some mother‐
boards to help identify what sensors are referencing. For exam‐
ple, a motherboard may have multiple sensors named 'TEMP'. The
entity id and instance number may help clarify which sensor
refers to "Processor 1" vs. "Processor 2".
--output-sensor-thresholds
Output sensor thresholds in output. This will add columns to the
default output for lower non-recoverable, lower critical, lower
non-critical, upper non-critical, upper critical, and upper non-
recoverable thresholds.
--no-sensor-type-output
Do not show sensor type output for each entry. On many systems,
the sensor type is redundant to the name of the sensor. This can
especially be true if --entity-sensor-names is specified. If
the sensor name is sufficient, or if the sensor type is of no
interest to the user, this option can be specified to condense
output.
--comma-separated-output
Output fields in comma separated format.
--no-header-output
Do not output column headers. May be useful in scripting.
--non-abbreviated-units
Output non-abbreviated units (e.g. 'Amps' instead of 'A'). May
aid in disambiguation of units (e.g. 'C' for Celsius or
Coulombs).
--legacy-output
Output in legacy format. Newer options may not be applicable to
legacy output.
--ipmimonitoring-legacy-output
Output legacy format of legacy ipmimonitoring tool. Newer
options may not be applicable to legacy output.
SDR CACHE OPTIONS
This tool requires access to the sensor data repository (SDR) cache for
general operation. By default, SDR data will be downloaded and cached
on the local machine. The following options apply to the SDR cache.
-f, --flush-cache
Flush a cached version of the sensor data repository (SDR)
cache. The SDR is typically cached for faster subsequent access.
However, it may need to be flushed and re-generated if the SDR
has been updated on a system.
-Q, --quiet-cache
Do not output information about cache creation/deletion. May be
useful in scripting.
--sdr-cache-recreate
If the SDR cache is out of date or invalid, automatically recre‐
ate the sensor data repository (SDR) cache. This option may be
useful for scripting purposes.
--sdr-cache-file=FILE
Specify a specific sensor data repository (SDR) cache file to be
stored or read from. If this option is used when multiple hosts
are specified, the same SDR cache file will be used for all
hosts.
--sdr-cache-directory=DIRECTORY
Specify an alternate directory for sensor data repository (SDR)
caches to be stored or read from. Defaults to the home directory
if not specified.
HOSTRANGED OPTIONS
The following options manipulate hostranged output. See HOSTRANGED SUP‐
PORT below for additional information on hostranges.
-B, --buffer-output
Buffer hostranged output. For each node, buffer standard output
until the node has completed its IPMI operation. When specifying
this option, data may appear to output slower to the user since
the the entire IPMI operation must complete before any data can
be output. See HOSTRANGED SUPPORT below for additional informa‐
tion.
-C, --consolidate-output
Consolidate hostranged output. The complete standard output from
every node specified will be consolidated so that nodes with
identical output are not output twice. A header will list those
nodes with the consolidated output. When this option is speci‐
fied, no output can be seen until the IPMI operations to all
nodes has completed. If the user breaks out of the program
early, all currently consolidated output will be dumped. See
HOSTRANGED SUPPORT below for additional information.
-F NUM, --fanout=NUM
Specify multiple host fanout. A "sliding window" (or fanout)
algorithm is used for parallel IPMI communication so that slower
nodes or timed out nodes will not impede parallel communication.
The maximum number of threads available at the same time is lim‐
ited by the fanout. The default is 64.
-E, --eliminate
Eliminate hosts determined as undetected by ipmidetect. This
attempts to remove the common issue of hostranged execution tim‐
ing out due to several nodes being removed from service in a
large cluster. The ipmidetectd daemon must be running on the
node executing the command.
--always-prefix
Always prefix output, even if only one host is specified or com‐
municating in-band. This option is primarily useful for script‐
ing purposes. Option will be ignored if specified with the -C
option.
HOSTRANGED SUPPORT
Multiple hosts can be input either as an explicit comma separated lists
of hosts or a range of hostnames in the general form: prefix[n-m,l-
k,...], where n < m and l < k, etc. The later form should not be con‐
fused with regular expression character classes (also denoted by []).
For example, foo[19] does not represent foo1 or foo9, but rather repre‐
sents a degenerate range: foo19.
This range syntax is meant only as a convenience on clusters with a
prefixNN naming convention and specification of ranges should not be
considered necessary -- the list foo1,foo9 could be specified as such,
or by the range foo[1,9].
Some examples of range usage follow:
foo[01-05] instead of foo01,foo02,foo03,foo04,foo05
foo[7,9-10] instead of foo7,foo9,foo10
foo[0-3] instead of foo0,foo1,foo2,foo3
As a reminder to the reader, some shells will interpret brackets ([ and
]) for pattern matching. Depending on your shell, it may be necessary
to enclose ranged lists within quotes.
When multiple hosts are specified by the user, a thread will be exe‐
cuted for each host in parallel up to the configured fanout (which can
be adjusted via the -F option). This will allow communication to large
numbers of nodes far more quickly than if done in serial.
By default, standard output from each node specified will be output
with the hostname prepended to each line. Although this output is read‐
able in many situations, it may be difficult to read in other situa‐
tions. For example, output from multiple nodes may be mixed together.
The -B and -C options can be used to change this default.
In-band IPMI Communication will be used when the host "localhost" is
specified. This allows the user to add the localhost into the hos‐
tranged output.
GENERAL TROUBLESHOOTING
Most often, IPMI problems are due to configuration problems.
IPMI over LAN problems involve a misconfiguration of the remote
machine's BMC. Double check to make sure the following are configured
properly in the remote machine's BMC: IP address, MAC address, subnet
mask, username, user enablement, user privilege, password, LAN privi‐
lege, LAN enablement, and allowed authentication type(s). For IPMI 2.0
connections, double check to make sure the cipher suite privilege(s)
and K_g key are configured properly. The bmc-config(8) tool can be used
to check and/or change these configuration settings.
Inband IPMI problems are typically caused by improperly configured
drivers or non-standard BMCs.
In addition to the troubleshooting tips below, please see WORKAROUNDS
below to also if there are any vendor specific bugs that have been dis‐
covered and worked around.
Listed below are many of the common issues for error messages. For
additional support, please e-mail the <freeipmi-users@gnu.org> mailing
list.
"username invalid" - The username entered (or a NULL username if none
was entered) is not available on the remote machine. It may also be
possible the remote BMC's username configuration is incorrect.
"password invalid" - The password entered (or a NULL password if none
was entered) is not correct. It may also be possible the password for
the user is not correctly configured on the remote BMC.
"password verification timeout" - Password verification has timed out.
A "password invalid" error (described above) or a generic "session
timeout" (described below) occurred. During this point in the protocol
it cannot be differentiated which occurred.
"k_g invalid" - The K_g key entered (or a NULL K_g key if none was
entered) is not correct. It may also be possible the K_g key is not
correctly configured on the remote BMC.
"privilege level insufficient" - An IPMI command requires a higher user
privilege than the one authenticated with. Please try to authenticate
with a higher privilege. This may require authenticating to a different
user which has a higher maximum privilege.
"privilege level cannot be obtained for this user" - The privilege
level you are attempting to authenticate with is higher than the maxi‐
mum allowed for this user. Please try again with a lower privilege. It
may also be possible the maximum privilege level allowed for a user is
not configured properly on the remote BMC.
"authentication type unavailable for attempted privilege level" - The
authentication type you wish to authenticate with is not available for
this privilege level. Please try again with an alternate authentication
type or alternate privilege level. It may also be possible the avail‐
able authentication types you can authenticate with are not correctly
configured on the remote BMC.
"cipher suite id unavailable" - The cipher suite id you wish to authen‐
ticate with is not available on the remote BMC. Please try again with
an alternate cipher suite id. It may also be possible the available
cipher suite ids are not correctly configured on the remote BMC.
"ipmi 2.0 unavailable" - IPMI 2.0 was not discovered on the remote
machine. Please try to use IPMI 1.5 instead.
"connection timeout" - Initial IPMI communication failed. A number of
potential errors are possible, including an invalid hostname specified,
an IPMI IP address cannot be resolved, IPMI is not enabled on the
remote server, the network connection is bad, etc. Please verify con‐
figuration and connectivity.
"session timeout" - The IPMI session has timed out. Please reconnect.
If this error occurs often, you may wish to increase the retransmission
timeout. Some remote BMCs are considerably slower than others.
"device not found" - The specified device could not be found. Please
check configuration or inputs and try again.
"driver timeout" - Communication with the driver or device has timed
out. Please try again.
"message timeout" - Communication with the driver or device has timed
out. Please try again.
"BMC busy" - The BMC is currently busy. It may be processing informa‐
tion or have too many simultaneous sessions to manage. Please wait and
try again.
"could not find inband device" - An inband device could not be found.
Please check configuration or specify specific device or driver on the
command line.
"driver timeout" - The inband driver has timed out communicating to the
local BMC or service processor. The BMC or service processor may be
busy or (worst case) possibly non-functioning.
"internal IPMI error" - An IPMI error has occurred that FreeIPMI does
not know how to handle. Please e-mail <freeipmi-users@gnu.org> to
report the issue.
"sensor config file parse error" - A parse error was found in the sen‐
sor interpretation configuration file. Please see freeipmi_inter‐
pret_sensor.conf(5).
WORKAROUNDS
With so many different vendors implementing their own IPMI solutions,
different vendors may implement their IPMI protocols incorrectly. The
following describes a number of workarounds currently available to han‐
dle discovered compliance issues. When possible, workarounds have been
implemented so they will be transparent to the user. However, some will
require the user to specify a workaround be used via the -W option.
The hardware listed below may only indicate the hardware that a problem
was discovered on. Newer versions of hardware may fix the problems
indicated below. Similar machines from vendors may or may not exhibit
the same problems. Different vendors may license their firmware from
the same IPMI firmware developer, so it may be worthwhile to try work‐
arounds listed below even if your motherboard is not listed.
If you believe your hardware has an additional compliance issue that
needs a workaround to be implemented, please contact the FreeIPMI main‐
tainers on <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
assumeio - This workaround flag will assume inband interfaces communi‐
cate with system I/O rather than being memory-mapped. This will work
around systems that report invalid base addresses. Those hitting this
issue may see "device not supported" or "could not find inband device"
errors. Issue observed on HP ProLiant DL145 G1.
spinpoll - This workaround flag will inform some inband drivers (most
notably the KCS driver) to spin while polling rather than putting the
process to sleep. This may significantly improve the wall clock running
time of tools because an operating system scheduler's granularity may
be much larger than the time it takes to perform a single IPMI message
transaction. However, by spinning, your system may be performing less
useful work by not contexting out the tool for a more useful task.
authcap - This workaround flag will skip early checks for username
capabilities, authentication capabilities, and K_g support and allow
IPMI authentication to succeed. It works around multiple issues in
which the remote system does not properly report username capabilities,
authentication capabilities, or K_g status. Those hitting this issue
may see "username invalid", "authentication type unavailable for
attempted privilege level", or "k_g invalid" errors. Issue observed on
Asus P5M2/P5MT-R/RS162-E4/RX4, Intel SR1520ML/X38ML, and Sun Fire
2200/4150/4450 with ELOM.
nochecksumcheck - This workaround flag will tell FreeIPMI to not check
the checksums returned from IPMI command responses. It works around
systems that return invalid checksums due to implementation errors, but
the packet is otherwise valid. Users are cautioned on the use of this
option, as it removes validation of packet integrity in a number of
circumstances. However, it is unlikely to be an issue in most situa‐
tions. Those hitting this issue may see "connection timeout", "session
timeout", or "password verification timeout" errors. On IPMI 1.5 con‐
nections, the "noauthcodecheck" workaround may also needed too. Issue
observed on Supermicro X9SCM-iiF, Supermicro X9DRi-F, and Supermicro
X9DRFR.
idzero - This workaround flag will allow empty session IDs to be
accepted by the client. It works around IPMI sessions that report empty
session IDs to the client. Those hitting this issue may see "session
timeout" errors. Issue observed on Tyan S2882 with M3289 BMC.
unexpectedauth - This workaround flag will allow unexpected non-null
authcodes to be checked as though they were expected. It works around
an issue when packets contain non-null authentication data when they
should be null due to disabled per-message authentication. Those hit‐
ting this issue may see "session timeout" errors. Issue observed on
Dell PowerEdge 2850,SC1425. Confirmed fixed on newer firmware.
forcepermsg - This workaround flag will force per-message authentica‐
tion to be used no matter what is advertised by the remote system. It
works around an issue when per-message authentication is advertised as
disabled on the remote system, but it is actually required for the pro‐
tocol. Those hitting this issue may see "session timeout" errors.
Issue observed on IBM eServer 325.
endianseq - This workaround flag will flip the endian of the session
sequence numbers to allow the session to continue properly. It works
around IPMI 1.5 session sequence numbers that are the wrong endian.
Those hitting this issue may see "session timeout" errors. Issue
observed on some Sun ILOM 1.0/2.0 (depends on service processor
endian).
noauthcodecheck - This workaround flag will tell FreeIPMI to not check
the authentication codes returned from IPMI 1.5 command responses. It
works around systems that return invalid authentication codes due to
hashing or implementation errors. Users are cautioned on the use of
this option, as it removes an authentication check verifying the valid‐
ity of a packet. However, in most organizations, this is unlikely to be
a security issue. Those hitting this issue may see "connection time‐
out", "session timeout", or "password verification timeout" errors.
Issue observed on Xyratex FB-H8-SRAY.
intel20 - This workaround flag will work around several Intel IPMI 2.0
authentication issues. The issues covered include padding of usernames,
and password truncation if the authentication algorithm is HMAC-
MD5-128. Those hitting this issue may see "username invalid", "password
invalid", or "k_g invalid" errors. Issue observed on Intel SE7520AF2
with Intel Server Management Module (Professional Edition).
supermicro20 - This workaround flag will work around several Supermicro
IPMI 2.0 authentication issues on motherboards w/ Peppercon IPMI
firmware. The issues covered include handling invalid length authenti‐
cation codes. Those hitting this issue may see "password invalid"
errors. Issue observed on Supermicro H8QME with SIMSO daughter card.
Confirmed fixed on newerver firmware.
sun20 - This workaround flag will work work around several Sun IPMI 2.0
authentication issues. The issues covered include invalid lengthed hash
keys, improperly hashed keys, and invalid cipher suite records. Those
hitting this issue may see "password invalid" or "bmc error" errors.
Issue observed on Sun Fire 4100/4200/4500 with ILOM. This workaround
automatically includes the "opensesspriv" workaround.
opensesspriv - This workaround flag will slightly alter FreeIPMI's IPMI
2.0 connection protocol to workaround an invalid hashing algorithm used
by the remote system. The privilege level sent during the Open Session
stage of an IPMI 2.0 connection is used for hashing keys instead of the
privilege level sent during the RAKP1 connection stage. Those hitting
this issue may see "password invalid", "k_g invalid", or "bad rmcpplus
status code" errors. Issue observed on Sun Fire 4100/4200/4500 with
ILOM, Inventec 5441/Dell Xanadu II, Supermicro X8DTH, Supermicro X8DTG,
Intel S5500WBV/Penguin Relion 700, Intel S2600JF/Appro 512X, and Quanta
QSSC-S4R/Appro GB812X-CN. This workaround is automatically triggered
with the "sun20" workaround.
integritycheckvalue - This workaround flag will work around an invalid
integrity check value during an IPMI 2.0 session establishment when
using Cipher Suite ID 0. The integrity check value should be 0 length,
however the remote motherboard responds with a non-empty field. Those
hitting this issue may see "k_g invalid" errors. Issue observed on
Supermicro X8DTG, Supermicro X8DTU, and Intel S5500WBV/Penguin Relion
700, and Intel S2600JF/Appro 512X.
assumemaxsdrrecordcount - This workaround will inform SDR reading to
stop reading after a known maximum numer of SDR records have been read.
This will work around systems that have mis-implemented SDR reading
functions that. Those hitting this issue may see "SDR record count
invalid" errors. Issue observed on unspecified Inspur motherboard.
discretereading - This workaround option will allow analog sensor read‐
ings (i.e. rpm, degrees, etc.) to be read even if the event/reading
type code for the sensor is for a discrete sensor (i.e. assert vs.
deassert). This option works around poorly defined (and arguably ille‐
gal) SDR records that expect analog sensor readings to be read along‐
side discrete sensors. This option is confirmed to work around issues
on HP Proliant DL380 G7 and HP ProLiant ML310 G5 motherboards.
ignorescanningdisabled - This workaround option will allow sensor read‐
ings to be read even if the sensor scanning bit indicates a sensor is
disabled. This option works around motherboards that incorrectly indi‐
cate sensors as disabled. This may problem may exist on your mother‐
board if sensors are listed as "N/A" even if they should be available.
This option is confirmed to work around issues on Dell Poweredge 2900,
Dell Poweredge 2950, Dell Poweredge R410, Dell Poweredge R610, and HP
Integrity rx3600 motherboards.
assumebmcowner - This workaround option will allow sensor readings to
be read if the sensor owner is the BMC, but the reported sensor owner
is not the BMC. Typically, sensors owned by a non-BMC sensor owner must
be bridged (e.g. with the --bridge-sensors option), however if the non-
BMC sensor owner is invalid, bridging fails. This option works around
motherboards that incorrectly report an non-BMC sensor owner by always
assuming the sensor owner is the BMC. This problem may exist on your
motherboard if sensors are listed as "N/A" even if they should be
available. This option is confirmed to work around issues on Fujitsu
RX300 and Fujitsu RX300S2 motherboards.
ignoreauthcode - This workaround option will allow sensor readings to
be read if the remote machine is invalidly calculating authentication
codes (i.e. authentication hashes) when communicating over LAN. This
problem may exist on your system if the error "session timeout" errors
or there is an appearance of a hang. Users are cautioned on the use of
this option, as it removes an authentication check verifying the valid‐
ity of a packet. However, in most organizations, this is unlikely to be
a security issue. The ignoring of authentication packets is only lim‐
ited to the period in which sensor readings are done, and not for any
portion of the session authentication or session teardown. This option
is confirmed to work on Inventec 5441/Dell Xanadu II and Inventec
5442/Dell Xanadu III. (Note: On the above systems, this issue has only
been observed when the --bridge-sensors is used.)
No IPMI 1.5 Support - Some motherboards that support IPMI 2.0 have been
found to not support IPMI 1.5. Those hitting this issue may see "ipmi
2.0 unavailable" or "connection timeout" errors. This issue can be
worked around by using IPMI 2.0 instead of IPMI 1.5 by specifying
--driver-type=LAN_2_0. Issue observed on HP Proliant DL 145.
OEM INTERPRETATION
The following motherboards are confirmed to have atleast some support
by the --interpret-oem-data option. While highly probable the OEM data
interpretations would work across other motherboards by the same manu‐
facturer, there are no guarantees. Some of the motherboards below may
be rebranded by vendors/distributors.
Dell Poweredge R210, Dell Poweredge R610, Dell Poweredge R710, Dell
Poweredge R720, Fujitsu iRMC S1 and iRMC S2 systems, HP Proliant DL160
G8, Intel S5500WB/Penguin Computing Relion 700, Intel S2600JF/Appro
512X, Intel S5000PAL, Supermicro X7DBR-3, Supermicro X7DB8, Supermicro
X8DTN, Supermicro X7SBI-LN4, Supermicro X8DTH, Supermicro X8DTG, Super‐
micro X8DTU, Supermicro X8DT3-LN4F, Supermicro X8DTU-6+, Supermicro
X8DTL, Supermicro X8DTL-3F, Supermicro X8SIL-F, Supermicro X9SCL,
Supermicro X9SCM, Supermicro X8DTN+-F, Supermicro X8SIE, Supermicro
X9SCA-F-O, Supermicro H8DGU-F, Supermicro X9DRi-F, Supermicro X9DRI-
LN4F+, Supermicro X9SPU-F-O, Supermicro X9SCM-iiF, Wistron/Dell Pow‐
eredge C6220.
EXAMPLES
# ipmi-sensors
Show all sensors and readings on the local machine.
# ipmi-sensors --verbose
Show verbose sensors and readings on the local machine.
# ipmi-sensors --record-ids="7,11,102"
Show sensor record ids 7, 11, and 102 on the local machine.
# ipmi-sensors --sensor-types=fan
Show all sensors of type fan on the local machine.
# ipmi-sensors -h ahost -u myusername -p mypassword
Show all sensors on a remote machine using IPMI over LAN.
# ipmi-sensors -h mycluster[0-127] -u myusername -p mypassword
Show all sensors across a cluster using IPMI over LAN.
DIAGNOSTICS
Upon successful execution, exit status is 0. On error, exit status is
1.
If multiple hosts are specified for communication, the exit status is 0
if and only if all targets successfully execute. Otherwise the exit
status is 1.
KNOWN ISSUES
On older operating systems, if you input your username, password, and
other potentially security relevant information on the command line,
this information may be discovered by other users when using tools like
the ps(1) command or looking in the /proc file system. It is generally
more secure to input password information with options like the -P or
-K options. Configuring security relevant information in the FreeIPMI
configuration file would also be an appropriate way to hide this infor‐
mation.
In order to prevent brute force attacks, some BMCs will temporarily
"lock up" after a number of remote authentication errors. You may need
to wait awhile in order to this temporary "lock up" to pass before you
may authenticate again.
Some sensors may be output as not available (i.e. N/A) because the
owner of the sensor is not the BMC. To attempt to bridge sensors and
access sensors not on the BMC, users may wish to try the -b or
--bridge-sensors options.
REPORTING BUGS
Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
COPYRIGHT
Copyright © 2003-2012 FreeIPMI Core Team.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 3 of the License, or (at your
option) any later version.
SEE ALSO
freeipmi(7), bmc-config(8), bmc-device(8), ipmi-sensors-config(8),
freeipmi_interpret_sensor.conf(5)
http://www.gnu.org/software/freeipmi/
IPMI Sensors version 1.2.9 2014-05-01 IPMI-SENSORS(8)
[top]
List of man pages available for Oracle
Copyright (c) for man pages and the logo by the respective OS vendor.
For those who want to learn more, the polarhome community provides shell access and support.
[legal]
[privacy]
[GNU]
[policy]
[cookies]
[netiquette]
[sponsors]
[FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
|
|
Vote for polarhome
|
