lpadmin(8)

Name

lpadmin - configure cups printers and classes

lpadmin [ -E ] [ -U username ] [ -h server[:port] ] -d destination
lpadmin [ -E ] [ -U username ] [ -h server[:port] ] -p destination [ -R name-default ] option(s)
lpadmin [ -E ] [ -U username ] [ -h server[:port] ] -x destination

Description

lpadmin configures printer and class queues provided by CUPS. It can also be used to set the server default printer or class.

When specified before the -d, -p, or -x options, the -E option forces encryption when connecting to the server.

The first form of the command (-d) sets the default printer or class to destination. Subsequent print jobs submitted via the lp(1) or lpr(1) commands will use this destination unless the user specifies otherwise with the lpoptions(1) command.

The second form of the command (-p) configures the named printer or class. The additional options are described below.

The third form of the command (-x) deletes the printer or class destination. Any jobs that are pending for the destination will be removed and any job that is currently printed will be aborted.

Options

The following options are recognized when configuring a printer queue:

-c class: Adds the named printer to class. If class does not exist it is created automatically.
-i ppd-file
-P ppd-file: Specifies a PostScript Printer Description (PPD) file to use with the printer.
-m model: Sets a standard PPD file for the printer from the model directory or using one of the driver interfaces. Use the -m option with the lpinfo(8) command to get a list of supported models. The model "raw" clears any existing PPD file and the model "everywhere" queries the printer referred to by the specified IPP device-uri. Note: The "raw" model is deprecated and will not be supported in a future version of CUPS.
-o cupsIPPSupplies=true
-o cupsIPPSupplies=false: Specifies whether IPP supply level values should be reported.
-o cupsSNMPSupplies=true
-o cupsSNMPSupplies=false: Specifies whether SNMP supply level (RFC 3805) values should be reported.
-o job-k-limit=value: Sets the kilobyte limit for per-user quotas. The value is an integer number of kilobytes; one kilobyte is 1024 bytes.
-o job-page-limit=value: Sets the page limit for per-user quotas. The value is the integer number of pages that can be printed; double-sided pages are counted as two pages.
-o job-quota-period=value: Sets the accounting period for per-user quotas. The value is an integer number of seconds; 86,400 seconds are in one day.
-o job-sheets-default=banner
-o job-sheets-default=banner,banner: Sets the default banner page(s) to use for print jobs.
-o name=value: Sets a PPD option for the printer. PPD options can be listed using the -l option with the lpoptions(1) command.
-o name-default=value: Sets a default server-side option for the destination. Any print-time option can be defaulted, e.g., "-o number-up-default=2" to set the default "number-up" option value to 2.
-o port-monitor=name: Sets the binary communications program to use when printing, "none", "bcp", or "tbcp". The default program is "none". The specified port monitor must be listed in the printer's PPD file.
-o printer-error-policy=name: Sets the error policy to be used when the printer backend is unable to send the job to the printer. The name must be one of "abort-job", "retry-job", "retry-current-job", or "stop-printer". The default error policy is "stop-printer" for printers and "retry-current-job" for classes.
-o printer-is-shared=true
-o printer-is-shared=false: Sets the destination to shared/published or unshared/unpublished. Shared/published destinations are publicly announced by the server on the LAN based on the browsing configuration in cupsd.conf, while unshared/unpublished destinations are not announced. The default value is "true".
-o printer-op-policy=name: Sets the IPP operation policy associated with the destination. The name must be defined in the cupsd.conf in a Policy section. The default operation policy is "default".
-R name-default: Deletes the named option from printer.
-r class: Removes the named printer from class. If the resulting class becomes empty it is removed.
-u allow:{user|@group}{,user|,@group}*
-u deny:{user|@group}{,user|,@group}*
-u allow:all
-u deny:none: Sets user-level access control on a destination. Names starting with "@" are interpreted as UNIX groups. The latter two forms turn user-level access control off. Note: The user 'root' is not granted special access - using "-u allow:foo,bar" will allow users 'foo' and 'bar' to access the printer but NOT 'root'.
-v "device-uri": Sets the device-uri attribute of the printer queue. Use the -v option with the lpinfo(8) command to get a list of supported device URIs and schemes.
-D "info": Provides a textual description of the destination.
-E: When specified before the -d, -p, or -x options, forces the use of TLS encryption on the connection to the scheduler. Otherwise, enables the destination and accepts jobs; this is the same as running the cupsaccept(8) and cupsenable(8) programs on the destination.
-L "location": Provides a textual location of the destination.

Conforming To

Unlike the System V printing system, CUPS allows printer names to contain any printable character except SPACE, TAB, "/", or "#". Also, printer and class names are not case-sensitive. Finally, the CUPS version of lpadmin may ask the user for an access password depending on the printing system configuration. This differs from the System V version which requires the root user to execute this command.

Notes

The CUPS version of lpadmin does not support all of the System V or Solaris printing system configuration options.

The double meaning of the -E option is an unfortunate historical oddity.

Example

Create an IPP Everywhere print queue:


    lpadmin -p myprinter -E -v ipp://myprinter.local/ipp/print -m everywhere