/sys$common/syshlp/helplib.hlb MOUNT, Parameters  *Conan The Librarian (sorry for the slow response - running on an old VAX)

 device-name[:][,...]

    Specifies the physical device name or logical name of the device
    on which the volume is to be mounted. On a system where volumes
    are not connected to HSCs (hierarchical storage controllers), use
    the following format:

       ddcu:

    The dd describes the device type of the physical devices used.
    For example, an RA60 disk drive is device type DJ, and an RA80
    or RA81 disk drive is device type DU. The c identifies the
    controller, and the u identifies the unit number of the device.

    On a system with HSCs, use one of the following formats:

       node$ddcu:
       allocation-class$ddcu:

    If your devices are dual ported to HSCs, use the allocation-
    class format. For example, $125$DUA23 represents an RA80 or RA81
    disk with unit number 23. The disk's allocation class is $125$.
    The c part of the format is always A for HSC disks. TROLL$DJA12
    represents an RA60 disk with unit number 12. The device is
    connected to an HSC named TROLL. Refer to OpenVMS Cluster Systems
    for more information about naming conventions.

    Device names can be generic so that if no controller or unit
    number is specified, the system attempts to mount the first
    available device that satisfies those specified components of the
    device names. If no volume is physically mounted on the specified
    device, MOUNT displays a message requesting that you place the
    volume in the device; after you place the volume in the named
    drive, MOUNT then completes the operation.

    If you specify more than one device name for a disk or magnetic
    tape volume set, separate the device names with either commas
    or plus signs. For a magnetic tape volume set, you can specify
    more volume labels than device names or more device names than
    volumes.

 volume-label[,...]

    Specifies the label on the volume.

    The number of characters allowed in a label depends on the type
    of device, as follows:

                       Number of Characters
    Device Type        in Label

    Magnetic tape      0-6
    Files-11 disk      1-12
    ISO 9660 disk      1-32

    OpenVMS requires disk volume labels to be unique in the first 12
    characters within a given domain. For example, disks mounted by
    different members of the same group using the /GROUP qualifier
    must be unique. However, disks mounted in different domains,
    such as one mounted using the /GROUP qualifier and one mounted
    privately, can use the same volume label.

    If you mount an ISO 9660 volume using the /SYSTEM or /CLUSTER
    qualifier, and the volume label is not unique within the first 12
    characters, you must supply an alternate volume label using the
    qualifier /OVERRIDE=IDENTIFICATION. If you choose this option,
    then Mount verification is disabled for the device.

    In addition, if a volume is part of a volume set and the first
    12 characters of the volume-set name are the same as the first
    12 characters of the volume label, a lock manager deadlock will
    occur. To avoid this problem, you must override either the volume
    label (by using the /OVERRIDE qualifier) or the volume-set name
    (by using the /BIND qualifier).

    If you specify more than one volume label, separate the labels
    with either commas or plus signs. The volumes must be in the same
    volume set and the labels must be specified in ascending order
    according to relative volume number.

    When you mount a magnetic tape volume set, the number of volume
    labels need not equal the number of device names specified.
    When a magnetic tape reaches the end-of-tape (EOT) mark, the
    system requests the operator to mount the next volume on one of
    the devices. The user is not informed of this request; only the
    operator is informed.

    When you mount a disk volume set, each volume label specified in
    the list must correspond to a device name in the same position in
    the device name list.

    The volume-label parameter is not required when you mount a
    volume with the /FOREIGN or /NOLABEL qualifier or when you
    specify /OVERRIDE=IDENTIFICATION. To specify a logical name
    when you enter either of these qualifiers, type any alphanumeric
    characters in the volume-label parameter position.

 logical-name[:]

    Defines a 1- to 255-alphanumeric character string logical name to
    be associated with the volume.

    If you do not specify a logical name, the MOUNT command assigns
    the default logical name DISK$volume-label to individual disk
    drives; it assigns the default logical name DISK$volume-set-name
    to the device on which the root volume of a disk volume set is
    mounted. Note that if you specify a logical name in the mount
    request that is different from DISK$volume-label or DISK$volume-
    set-name, then two logical names are associated with the device.

    If you do not specify a logical name for a magnetic tape drive,
    the MOUNT command assigns only one logical name, TAPE$volume-
    label, to the first magnetic tape device in the list. No default
    logical volume-set name is assigned in this case.

    The MOUNT command places the name in the process logical name
    table, unless you specify /GROUP or /SYSTEM. In the latter cases,
    it places the logical names in the group or system logical name
    table.

    If you specify the /CLUSTER qualifier, the logical name is
    established on each node in the cluster.

                                   NOTE

       Avoid assigning a logical name that matches the file name
       of an executable image in SYS$SYSTEM. Such an assignment
       prohibits you from invoking that image.

    Do not use the logical name assigned to a volume as a distributed
    file system (DFS) access point. If you attempt to add a DFS
    access point using the same name as the logical name, DFS fails
    as in the following example:

    $ SHOW LOG DISK$*

    (LNM$SYSTEM_TABLE)

       "DISK$TIVOLI_SYS" = "TIVOLI$DUA0:"

    $ MCR DFS$CONTROL
    DFS> ADD ACCESS DISK$TIVOLI_SYS TIVOLI$DUA0:[000000]
    %DNS-W-NONSNAME, Unknown namespace name specified

    If the logical name of a volume is in a process-private table,
    then the name is not deleted when the volume is dismounted.