XGI(4)XGI(4)NAMExgi - XGI video driver
SYNOPSIS
Section "Device"
Identifier "devname"
Driver "xgi"
...
EndSection
DESCRIPTIONxgi is an XFree86 driver for XGI video chips. The driver is acceler‐
ated, and provides support for colordepths of 8, 16 and 24 bpp.
XVideo, Render and other extensions are supported as well.
SUPPORTED HARDWARE
The xgi driver supports PCI and AGP video cards based on the following
chipsets:
XGI5597/5598 XGI530/620 XGI6326/AGP/DVD XGI300/305 XGI540 XGI630/730
XGI315/H/PRO XGI550/551/552 XGI650/651/M650/661FX/M661FX/M661MX/740/741
XGI330 (Xabre) XGI760
In the following text, the following terms are used:
old series for XGI5597/5598, 530/620 and 6326/AGP/DVD
300 series for XGI300/305, 540 and 630/730
315/330 series for XGI315/H/PRO, 55x and (M)65x/(M)661xX/74x, 330, 760
Note: Support for 661FX, M661FX, M661MX, 741 and 760 is untested.
CONFIGURATION DETAILS
Please refer to XF86Config(5) for general configuration details. This
section only covers configuration details specific to this driver.
Detailed information on all supported options can be obtained at
http://www.winischhofer.net/linuxxgivga.shtml
This manpage only covers a subset of the supported options.
1. For all supported chipsets
The following driver Options are supported on all chipsets:
Option "NoAccel" "boolean"
Disable or enable 2D acceleration. Default: acceleration is
enabled.
Option "HWCursor" "boolean"
Enable or disable the HW cursor. Default: HWCursor is on.
Option "SWCursor" "boolean"
The opposite of HWCursor. Default: SWCursor is off.
Option "Rotate" "CW"
Rotate the display clockwise. This mode is unaccelerated, and
uses the Shadow Frame Buffer layer. Using this option disables
the Resize and Rotate extension (RandR). Default: no rotation.
Option "Rotate" "CCW"
Rotate the display counterclockwise. This mode is unaccelerated,
and uses the Shadow Frame Buffer layer. Using this option dis‐
ables the Resize and Rotate extension (RandR). Default: no
rotation.
Option "ShadowFB" "boolean"
Enable or disable use of the shadow framebuffer layer. Default:
Shadow framebuffer is off.
Option "CRT1Gamma" "boolean"
Enable or disable gamma correction. Default: Gamma correction
is on.
2. Old series specific information
The driver will auto-detect the amount of video memory present for all
these chips, but in the case of the 6326, it will limit the memory size
to 4MB. This is because the 6326's 2D engine can only address 4MB. The
remaining memory seems to be intended for 3D texture data, since only
the 3D engine can address RAM above 4MB. However, you can override this
limitation using the "VideoRAM" option in the Device section if your
board has more than 4MB and you need to use it. However, 2D accelera‐
tion, Xvideo and the HWCursor will be disabled in this case.
The driver will also auto-detect the maximum dotclock and DAC speed.
If you have problems getting high resolutions because of dot clock lim‐
itations, try using the "DacSpeed" option, also in the Device section.
However, this is not recommended for the 6326. For this chip, the
driver has two built-in modes for high resolutions which you should use
instead. These are named "XGI1280x1024-75" and "XGI1600x1200-60" and
they will be added to the list of default modes. To use these modes,
just place them in your Screen section. Example:
Modes "XGI1600x1200-60" "XGI1280x1024x75" "1024x768" ...
Of these modes, 1280x1024 is only available at 8, 15 and 16bpp.
1600x1200 is available at 8bpp only.
TV support for the 6326
TV output is supported for the 6326. The driver will auto detect a TV
connected and in this case add the following modes to the list of
default modes: "PAL800x600", "PAL800x600U", "PAL720x540", "PAL640x480",
"NTSC640x480", "NTSC640x480U" and "NTSC640x400". Use these modes like
the hi-res modes described above.
The following driver Options are supported on the old series:
Option "TurboQueue" "boolean"
Enable or disable TurboQueue mode. Default: off for 530/620, on
for the others
Option "FastVram" "boolean"
Enable or disable FastVram mode. Enabling this sets the video
RAM timing to one cycle per read operation instead of two
cycles. Disabling this will set two cycles for read and write
operations. Leaving this option out uses the default, which
varies depending on the chipset.
Option "NoHostBus" "boolean"
(XGI5597/5598 only). Disable CPU-to-VGA host bus support. This
speeds up CPU to video RAM transfers. Default: Host bus is
enabled.
Option "NoXVideo" "boolean"
Disable XV (XVideo) extension support. Default: XVideo is on.
Option "NoYV12" "boolean"
Disable YV12 Xv support. This might me required due to hardware
bugs in some chipsets. Disabling YV12 support forces Xv-aware
applications to use YUV2 or XShm for video output. Default:
YV12 support is on.
Option "TVStandard" "string"
(6326 only) Valid parameters are PAL or NTSC. The default is
set by a jumper on the card.
Option "TVXPosOffset" "integer"
(6326 only) This option allows tuning the horizontal position of
the image for TV output. The range is from -16 to 16. Default: 0
Option "TVYPosOffset" "integer"
(6326 only) This option allows tuning the vertical position of
the image for TV output. The range is from -16 to 16. Default: 0
Option "XGI6326TVEnableYFilter" "boolean"
(6326 only) This option allows enabling/disabling the Y (chroma)
filter for TV output.
Option "XGI6326TVAntiFlicker" "string"
(6326 only) This option allow enabling/disabling the anti
flicker facility for TV output. Possible parameters are OFF,
LOW, MED, HIGH or ADAPTIVE. By experience, ADAPTIVE yields the
best results, hence it is the default.
2. 300 and 315/330 series specific information
The 300 and 315/330 series feature two CRT controllers and very often
come with a video bridge for controlling LCD and TV output. Here‐
inafter, the term CRT1 refers to the VGA output of the chip, and CRT2
refers to either LCD, TV or secondary VGA. Due to timing reasons, only
one CRT2 output can be active at the same time. But this limitation
does not apply to using CRT1 and CRT2 at the same time which makes it
possible to run the driver in dual head mode.
The driver supports the following video bridges:
XGI301 XGI301B(-DH) XGI301C XGI301LV(X) XGI302LV
Instead of a video bridge, some machines have a LVDS transmitter to
control LCD panels, and a Chrontel 7005 or 7019 for TV output. All
these are supported as well.
About TV output
On the XGI301 and the Chrontel 7005, only resolutions up to 800x600 are
supported. On all others, resolutions up to 1024x768 are supported.
However, due to a hardware bug, Xvideo might be distorted on XGI video
bridges if running NTSC or PAL-M at 1024x768.
About XVideo support
XVideo is supported on all chipsets of both families. However, there
are some differences in hardware features which cause limitations. The
300 series as well as the XGI55x, M650, 651, 661FX, M661FX, and 741
support two video overlays. The XGI315/H/PRO, 650/740 and 330 support
only one such overlay. On chips with two overlays, one overlay is used
for CRT1, the other for CRT2. On the other chipsets, the option "XvOn‐
CRT2" can be used to select the desired output channel.
About Merged Framebuffer support
This mode is strongly recommended over Xinerama. Please see
http://www.winischhofer.net/linuxxgivga.shtml for detailed information.
About dual-head support
Dual head mode has some limitations as regards color depth and resolu‐
tion. Due to memory bandwidth limits, CRT1 might have a reduced maximum
refresh rate if running on higher resolutions than 1280x1024.
Colordepth 8 is not supported when running in dual head mode.
The following driver Options are supported on the 300 and 315/330
series:
Option "NoXVideo" "boolean"
Disable XV (XVideo) extension support. Default: XVideo is on.
Option "XvOnCRT2" "boolean"
On chipsets with only one video overlay, this option can used to
bind the overlay to CRT1 ( if a monitor is detected and if this
option is either unset or set to false ) or CRT2 ( if a CRT2
device is detected or forced, and if this option is set to true
). If either only CRT1 or CRT2 is detected, the driver decides
automatically. In Merged Framebuffer mode, this option is
ignored. Default: overlay is used on CRT1
Option "ForceCRT1" "boolean"
Force CRT1 to be on of off. If a monitor is connected, it will
be detected during server start. However, some old monitors are
not detected correctly. In such cases, you may set this option
to on in order to make the driver initialize CRT1 anyway. If
this option is set to off , the driver will switch off CRT1.
Default: auto-detect
Option "ForceCRT2Type" "string"
Force display type to one of: NONE , TV , SVIDEO , COMPOSITE ,
SVIDEO+COMPOSITE , SCART , LCD , VGA ; NONE will disable CRT2.
The SVIDEO, COMPOSITE, SVIDEO+COMPOSITE and SCART parameters are
for XGI video bridges only and can be used to force the driver
to use a specific TV output connector (if present). Default:
auto detect.
Option "CRT2Gamma" "boolean"
Enable or disable gamma correction for CRT2. Only supported for
XGI video bridges. Default: Gamma correction for CRT2 is on.
Option "TVStandard" "string"
Force the TV standard to either PAL or NTSC. On some machines
with 630, 730 and the 315/330 series, PALM , PALN and NTSCJ are
supported as well. Default: BIOS setting.
Option "TVXPosOffset" "integer"
This option allows tuning the horizontal position of the image
for TV output. The range is from -32 to 32. Not supported on the
Chrontel 7019. Default: 0
Option "TVYPosOffset" "integer"
This option allows tuning the vertical position of the image for
TV output. The range is from -32 to 32. Not supported on the
Chrontel 7019. Default: 0
Option "XGITVXScale" "integer"
This option selects the horizontal zooming level for TV output.
The range is from -16 to 16. Only supported on XGI video
bridges. Default: 0
Option "XGITVYScale" "integer"
This option selects the vertical zooming level for TV output in
the following modes: 640x480, 800x600. On the 315/330 series,
also 720x480, 720x576 and 768x576. The range is from -4 to 3.
Only supported on XGI video bridges. Default: 0
Option "CHTVOverscan" "boolean"
On machines with a Chrontel TV encoder, this can be used to
force the TV mode to overscan or underscan. on means overscan,
off means underscan. Default: BIOS setting.
Option "CHTVSuperOverscan" "boolean"
On machines with a Chrontel 7005 TV encoder, this option enables
a super-overscan mode. This is only supported if the TV standard
is PAL. Super overscan will produce an image on the TV which is
larger than the viewable area.
The driver supports many more options. Please see http://www.winis‐
chhofer.net/linuxxgivga.shtml for more information.
3. 300 series specific information
DRI is supported on the 300 series only. On Linux, DRI requires the
kernel's XGI framebuffer driver ( xgifb ) and some other modules which
come with either the kernel or XFree86.
Xgifb takes care of memory management for texture data. In order to
prevent the X Server and xgifb from overwriting each other's data,
xgifb reserves an amount of video memory for the X driver. This amount
can either be selected using xgifb's mem parameter, or auto-selected
depending on the amount of total video RAM available.
Xgifb can be used for memory management only, or as a complete frame‐
buffer driver. If you start xgifb with a valid mode (ie you gain a
graphical console), the X driver can communicate with xgifb and doesn't
require any manual configuration for finding out about the video memory
it is allowed to use. However, if you are running a 2.4 series Linux
kernel and use xgifb for video memory management only, ie you started
xgifb with mode=none and still have a text mode console, there is no
communication between xgifb and the X driver. For this purpose, the
Option "MaxXFBMem" "integer"
exists. This option must be set to the same value as given to xgifb
through its "mem" parameter, ie the amount of memory to use for X in
kilobytes.
If you started xgifb without the mem argument, xgifb will reserve
12288KB if more than 16MB of total video RAM is available,
8192KB if between 12 and 16MB of video RAM is available,
4096KB in all other cases.
If you intend to use DRI, I recommend setting the total video memory in
the BIOS to 64MB in order to at least overcome the lack of memory swap
functions.
Option "DRI" "boolean"
This option allows enabling or disabling DRI. By default, DRI is
on.
Option "AGPSize" "integer"
This option allows selecting the amount of AGP memory to be used
for DRI. The amount is to be specified in megabyte, the default
is 8.
KNOWN BUGS
none.
SEE ALSOXFree86(1), XF86Config(5), xf86config(1), Xserver(1), X(7)
http://www.winischhofer.net/linuxxgivga.shtml for more information and
updates
AUTHORS
Authors include: Alan Hourihane, Mike Chapman, Juanjo Santamarta,
Mitani Hiroshi, David Thomas, Sung-Ching Lin, Ademar Reis, Thomas
Winischhofer
X Version 11 xf86-video-xgi 1.6.0 XGI(4)
