skc man page on MirBSD

Man page or keyword search:  
man Server   6113 pages
apropos Keyword Search (all sections)
Output format
MirBSD logo
[printable version]

SK(4)			   BSD Programmer's Manual			 SK(4)

NAME
     sk, skc - SysKonnect XMAC II and Marvell GMAC based gigabit ethernet

SYNOPSIS
     skc* at pci? dev ? function ?
     sk* at skc?

DESCRIPTION
     The sk driver provides support for SysKonnect based gigabit ethernet
     adapters and Marvell based gigabit ethernet adapters, including the fol-
     lowing:

	   +   SK-9821 SK-NET GE-T single port, copper adapter
	   +   SK-9822 SK-NET GE-T dual port, copper adapter
	   +   SK-9841 SK-NET GE-LX single port, single mode fiber adapter
	   +   SK-9842 SK-NET GE-LX dual port, single mode fiber adapter
	   +   SK-9843 SK-NET GE-SX single port, multimode fiber adapter
	   +   SK-9844 SK-NET GE-SX dual port, multimode fiber adapter
	   +   SK-9521 V2.0 single port, copper adapter (32-bit)
	   +   SK-9821 V2.0 single port, copper adapter
	   +   SK-9843 V2.0 single port, copper adapter
	   +   3com 3c940 single port, copper adapter
	   +   Linksys EG1032v2, copper adapter
	   +   Linksys EG1064v2, copper adapter
	   +   D-Link DGE-530T, copper adapter
	   +   SMC 9452TX, copper adapter

     The SysKonnect based adapters consist of two main components: the XaQti
     Corp. XMAC II Gigabit MAC (sk) and the SysKonnect GEnesis controller ASIC
     (skc). The XMAC provides the Gigabit MAC and PHY support while the
     GEnesis provides an interface to the PCI bus, DMA support, packet buffer-
     ing and arbitration. The GEnesis can control up to two XMACs simultane-
     ously, allowing dual-port NIC configurations.

     The Marvell based adapters are a single integrated circuit, but are still
     presented as a separate MAC (sk) and controller ASIC (skc). At this time,
     there are no dual-port Marvell based NICs.

     The sk driver configures dual port SysKonnect adapters such that each
     XMAC is treated as a separate logical network interface. Both ports can
     operate independently of each other and can be connected to separate net-
     works. The SysKonnect driver software currently only uses the second port
     on dual port adapters for failover purposes: if the link on the primary
     port fails, the SysKonnect driver will automatically switch traffic onto
     the second port.

     The XaQti XMAC II supports full and half duplex operation with autonego-
     tiation. The XMAC also supports unlimited frame sizes. Support for jumbo
     frames is provided via the interface MTU setting. Selecting an MTU larger
     than 1500 bytes with the ifconfig(8) utility configures the adapter to
     receive and transmit jumbo frames. Using jumbo frames can greatly improve
     performance for certain tasks, such as file transfers and data streaming.

     Hardware TCP/IP checksum offloading for IPv4 is supported.

     The following media types and options (as given to ifconfig(8)) are sup-
     ported:

	   media autoselect
		Enable autoselection of the media type and options. The user
		can manually override the autoselected mode by adding media
		options to the appropriate hostname.if(5) file.

	   media 1000baseSX mediaopt full-duplex
		Set 1000Mbps (Gigabit Ethernet) operation on fiber and force
		full-duplex mode.

	   media 1000baseSX mediaopt half-duplex
		Set 1000Mbps (Gigabit Ethernet) operation on fiber and force
		half-duplex mode.

	   media 1000baseT mediaopt full-duplex
		Set 1000Mbps (Gigabit Ethernet) operation and force full-
		duplex mode.

     For more information on configuring this device, see ifconfig(8). To view
     a list of media types and options supported by the card, try ifconfig -m
     <device>. For example, ifconfig -m sk0.

DIAGNOSTICS
     sk%d: couldn't map memory	A fatal initialization error has occurred.

     sk%d: couldn't map ports  A fatal initialization error has occurred.

     sk%d: couldn't map interrupt  A fatal initialization error has occurred.

     sk%d: failed to enable memory mapping!  The driver failed to initialize
     PCI shared memory mapping. This might happen if the card is not in a
     bus-master slot.

     sk%d: no memory for jumbo buffers!	 The driver failed to allocate memory
     for jumbo frames during initialization.

     sk%d: watchdog timeout  The device has stopped responding to the network,
     or there is a problem with the network connection (cable).

SEE ALSO
     arp(4), ifmedia(4), intro(4), netintro(4), pci(4), hostname.if(5),
     ifconfig(8)

     XaQti XMAC II datasheet, http://www.xaqti.com.

     SysKonnect GEnesis programming manual, http://www.syskonnect.com.

HISTORY
     The sk device driver first appeared in FreeBSD 3.0, and OpenBSD support
     was added in OpenBSD 2.6.

AUTHORS
     The sk driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

MirOS BSD #10-current		 July 3, 1999				     1
[top]

List of man pages available for MirBSD

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net