sendto man page on NetBSD

Man page or keyword search:  
man Server   9087 pages
apropos Keyword Search (all sections)
Output format
NetBSD logo
[printable version]

SEND(2)			    BSD System Calls Manual		       SEND(2)

NAME
     send, sendto, sendmsg — send a message from a socket

LIBRARY
     Standard C Library (libc, -lc)

SYNOPSIS
     #include <sys/socket.h>

     ssize_t
     send(int s, const void *msg, size_t len, int flags);

     ssize_t
     sendto(int s, const void *msg, size_t len, int flags,
	 const struct sockaddr *to, socklen_t tolen);

     ssize_t
     sendmsg(int s, const struct msghdr *msg, int flags);

DESCRIPTION
     send(), sendto(), and sendmsg() are used to transmit a message to another
     socket.  send() may be used only when the socket is in a connected state,
     while sendto() and sendmsg() may be used at any time.

     The address of the target is given by to with tolen specifying its size.
     The length of the message is given by len.	 If the message is too long to
     pass atomically through the underlying protocol, the error EMSGSIZE is
     returned, and the message is not transmitted.

     No indication of failure to deliver is implicit in a send().  Locally
     detected errors are indicated by a return value of -1.

     If no messages space is available at the socket to hold the message to be
     transmitted, then send() normally blocks, unless the socket has been
     placed in non-blocking I/O mode.  The select(2) or poll(2) call may be
     used to determine when it is possible to send more data.

     The flags parameter may include one or more of the following:

     #define MSG_OOB	     0x0001 /* process out-of-band data */
     #define MSG_PEEK	     0x0002 /* peek at incoming message */
     #define MSG_DONTROUTE   0x0004 /* bypass routing, use direct interface */
     #define MSG_EOR	     0x0008 /* data completes record */
     #define MSG_NOSIGNAL    0x0400 /* do not generate SIGPIPE on EOF */

     The flag MSG_OOB is used to send “out-of-band” data on sockets that sup‐
     port this notion (e.g.  SOCK_STREAM); the underlying protocol must also
     support “out-of-band” data.  MSG_EOR is used to indicate a record mark
     for protocols which support the concept.  MSG_DONTROUTE is usually used
     only by diagnostic or routing programs.

     See recv(2) for a description of the msghdr structure.  MSG_NOSIGNAL is
     used to prevent SIGPIPE generation when writing a socket that may be
     closed.

RETURN VALUES
     The call returns the number of characters sent, or -1 if an error
     occurred.

ERRORS
     send(), sendto(), and sendmsg() fail if:

     [EBADF]		An invalid descriptor was specified.

     [ENOTSOCK]		The argument s is not a socket.

     [EFAULT]		An invalid user space address was specified for a
			parameter.

     [EMSGSIZE]		The socket requires that message be sent atomically,
			and the size of the message to be sent made this
			impossible.

     [EPIPE]		In a connected socket the connection has been broken.

     [EDSTADDRREQ]	In a non-connected socket a destination address has
			not been specified.

     [EAGAIN|EWOULDBLOCK]
			The socket is marked non-blocking and the requested
			operation would block.

     [ENOBUFS]		The system was unable to allocate an internal buffer.
			The operation may succeed when buffers become avail‐
			able.

     [ENOBUFS]		The output queue for a network interface was full.
			This generally indicates that the interface has
			stopped sending, but may be caused by transient con‐
			gestion.

     [EACCES]		The SO_BROADCAST option is not set on the socket, and
			a broadcast address was given as the destination.

     [EHOSTUNREACH]	The destination for the message is unreachable.

     [EHOSTDOWN]	The destination is a host on the local subnet and does
			not respond to arp(4).

     [EINVAL]		The total length of the I/O is more than can be
			expressed by the ssize_t return value.

     [EAFNOSUPPORT]	Addresses in the specified address family cannot be
			used with this socket.

     sendto() will also fail if:

     [EISCONN]		A destination address was specified and the socket is
			already connected.

     sendmsg() will also fail if:

     [EMSGSIZE]		The msg_iovlen member of the msg structure is less
			than or equal to 0 or is greater than {IOV_MAX}.

SEE ALSO
     fcntl(2), getsockopt(2), recv(2), select(2), socket(2), write(2)

HISTORY
     The send() function call appeared in 4.2BSD.

BSD				  May 9, 2008				   BSD
[top]
                             _         _         _ 
                            | |       | |       | |     
                            | |       | |       | |     
                         __ | | __ __ | | __ __ | | __  
                         \ \| |/ / \ \| |/ / \ \| |/ /  
                          \ \ / /   \ \ / /   \ \ / /   
                           \   /     \   /     \   /    
                            \_/       \_/       \_/ 
More information is available in HTML format for server NetBSD

List of man pages available for NetBSD

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net