RECVFROM(P) POSIX Programmer's Manual RECVFROM(P)PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux
implementation of this interface may differ (consult the corresponding
Linux manual page for details of Linux behavior), or the interface may
not be implemented on Linux.
NAMErecvfrom - receive a message from a socket
SYNOPSIS
#include <sys/socket.h>
ssize_t recvfrom(int socket, void *restrict buffer, size_t length,
int flags, struct sockaddr *restrict address,
socklen_t *restrict address_len);
DESCRIPTION
The recvfrom() function shall receive a message from a connection-mode
or connectionless-mode socket. It is normally used with connectionless-
mode sockets because it permits the application to retrieve the source
address of received data.
The recvfrom() function takes the following arguments:
socket Specifies the socket file descriptor.
buffer Points to the buffer where the message should be stored.
length Specifies the length in bytes of the buffer pointed to by the
buffer argument.
flags Specifies the type of message reception. Values of this argument
are formed by logically OR'ing zero or more of the following
values:
MSG_PEEK
Peeks at an incoming message. The data is treated as unread and
the next recvfrom() or similar function shall still return this
data.
MSG_OOB
Requests out-of-band data. The significance and semantics of
out-of-band data are protocol-specific.
MSG_WAITALL
On SOCK_STREAM sockets this requests that the function block
until the full amount of data can be returned. The function may
return the smaller amount of data if the socket is a message-
based socket, if a signal is caught, if the connection is termi‐
nated, if MSG_PEEK was specified, or if an error is pending for
the socket.
address
A null pointer, or points to a sockaddr structure in which the
sending address is to be stored. The length and format of the
address depend on the address family of the socket.
address_len
Specifies the length of the sockaddr structure pointed to by the
address argument.
The recvfrom() function shall return the length of the message written
to the buffer pointed to by the buffer argument. For message-based
sockets, such as SOCK_RAW, SOCK_DGRAM, and SOCK_SEQPACKET, the
entire message shall be read in a single operation. If a message is
too long to fit in the supplied buffer, and MSG_PEEK is not set in the
flags argument, the excess bytes shall be discarded. For stream-based
sockets, such as SOCK_STREAM, message boundaries shall be ignored. In
this case, data shall be returned to the user as soon as it becomes
available, and no data shall be discarded.
If the MSG_WAITALL flag is not set, data shall be returned only up to
the end of the first message.
Not all protocols provide the source address for messages. If the
address argument is not a null pointer and the protocol provides the
source address of messages, the source address of the received message
shall be stored in the sockaddr structure pointed to by the address
argument, and the length of this address shall be stored in the object
pointed to by the address_len argument.
If the actual length of the address is greater than the length of the
supplied sockaddr structure, the stored address shall be truncated.
If the address argument is not a null pointer and the protocol does not
provide the source address of messages, the value stored in the object
pointed to by address is unspecified.
If no messages are available at the socket and O_NONBLOCK is not set on
the socket's file descriptor, recvfrom() shall block until a message
arrives. If no messages are available at the socket and O_NONBLOCK is
set on the socket's file descriptor, recvfrom() shall fail and set
errno to [EAGAIN] or [EWOULDBLOCK].
RETURN VALUE
Upon successful completion, recvfrom() shall return the length of the
message in bytes. If no messages are available to be received and the
peer has performed an orderly shutdown, recvfrom() shall return 0. Oth‐
erwise, the function shall return -1 and set errno to indicate the
error.
ERRORS
The recvfrom() function shall fail if:
EAGAIN or EWOULDBLOCK
The socket's file descriptor is marked O_NONBLOCK and no data is
waiting to be received; or MSG_OOB is set and no out-of-band
data is available and either the socket's file descriptor is
marked O_NONBLOCK or the socket does not support blocking to
await out-of-band data.
EBADF The socket argument is not a valid file descriptor.
ECONNRESET
A connection was forcibly closed by a peer.
EINTR A signal interrupted recvfrom() before any data was available.
EINVAL The MSG_OOB flag is set and no out-of-band data is available.
ENOTCONN
A receive is attempted on a connection-mode socket that is not
connected.
ENOTSOCK
The socket argument does not refer to a socket.
EOPNOTSUPP
The specified flags are not supported for this socket type.
ETIMEDOUT
The connection timed out during connection establishment, or due
to a transmission timeout on active connection.
The recvfrom() function may fail if:
EIO An I/O error occurred while reading from or writing to the file
system.
ENOBUFS
Insufficient resources were available in the system to perform
the operation.
ENOMEM Insufficient memory was available to fulfill the request.
The following sections are informative.
EXAMPLES
None.
APPLICATION USAGE
The select() and poll() functions can be used to determine when data is
available to be received.
RATIONALE
None.
FUTURE DIRECTIONS
None.
SEE ALSOpoll() , read() , recv() , recvmsg() , select() , send() , sendmsg() ,
sendto() , shutdown() , socket() , write() , the Base Definitions vol‐
ume of IEEE Std 1003.1-2001, <sys/socket.h>
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form
from IEEE Std 1003.1, 2003 Edition, Standard for Information Technology
-- Portable Operating System Interface (POSIX), The Open Group Base
Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of
Electrical and Electronics Engineers, Inc and The Open Group. In the
event of any discrepancy between this version and the original IEEE and
The Open Group Standard, the original IEEE and The Open Group Standard
is the referee document. The original Standard can be obtained online
at http://www.opengroup.org/unix/online.html .
IEEE/The Open Group 2003 RECVFROM(P)
