PPPOE(8) BSD System Manager's Manual PPPOE(8)NAMEpppoe - PPP Over Ethernet translator
SYNOPSISpppoe [-stv] [-i interface] [-n service] [-p system]
DESCRIPTION
The pppoe program can, with the help of ppp(8), act as a server or client
for running PPP Over Ethernet.
The options are as follows:
-i interface
Specify the interface that pppoe is to use, which should be a
real Ethernet interface (not a virtual device like tun(4)). If
this option is not specified, pppoe will use the first Ethernet
interface that is up and running.
-n service
Use service as the service name when negotiating with the server.
By default, the client will ask for any service, and expect the
server to respond with the same.
-p system
This argument is passed, uninterpreted, to ppp(8). It can be used
to specify the configuration data to be used for PPP Over Ether-
net connections. This option is only used in server mode.
-s If this option is specified, pppoe will run as a server. Other-
wise, pppoe runs as a client.
-t Instruct pppoe to ignore PADT packets. If you observe numerous
"connection reset by peer" error messages and constantly lose
connection soon after establishing one, it may because of spuri-
ous PADT tags being sent from the peer. Ignoring them may al-
leviate the problem.
-v For each use of the flag, the verbosity of pppoe increases.
CLIENT SETUP
Configuring the client involves setting up the configuration file for
ppp(8). The following statements must be included in the file for the
specified system (or ``default'' if no system is specified):
set device "!/usr/sbin/pppoe"
set mtu max 1454
set mru max 1454
set speed sync
disable acfcomp protocomp
deny acfcomp
The set device line tells ppp to use pppoe program for input and output
instead of using a serial port or other network connection. The mtu and
mru must be set to at maximum 1492, better 1454 (see below), to leave
room in the outgoing Ethernet packet for the pppoe headers. The set speed
sync line tells ppp to use synchronous encoding for the packets sent
between it and pppoe. According to RFC 2516, protocol compression,
protocomp, is not recommended, so it is disabled, but not denied. On the
other hand, address and control field compression, acfcomp, must be dis-
abled and denied.
Additionally, the authentication mechanism for the connection must be
specified as well as any other parameters.
EXAMPLE CONFIGURATION
Given a machine with one Ethernet interface, xl0, the first thing that
must be done is to bring the interface up:
# ifconfig xl0 up
This can be done automatically during boot with a /etc/hostname.xl0 file,
see hostname.if(5) for details.
Next, a /etc/ppp/ppp.conf file must be created. Below is a minimal PPPoE
style configuration, see ppp(8) for more options.
default:
set log Phase Chat LCP IPCP CCP tun command
pppoe:
set device "!/usr/sbin/pppoe -i xl0"
set mtu max 1454
set mru max 1454
set speed sync
disable acfcomp protocomp
deny acfcomp
set authname "myUsername"
set authkey "myPassword"
The default section sets up some helpful information to log while getting
started, and the pppoe section sets the required fields for a PPPoE con-
nection as well as the username and password to use to authenticate to
the service provider.
Once the /etc/ppp/ppp.conf file is set up, it is just a matter of setting
ppp(8) into action:
# ppp pppoe
Working in interactive mode
Using interface: tun0
ppp ON deepthought> dial
Ppp ON deepthought>
PPp ON deepthought>
PPP ON deepthought>
The userland ppp(8) daemon has many options for configuration, like ad-
ding default routes, network address translation, automatically using re-
mote DNS servers, automatic dialing, etc. Please see ppp(8) for details.
Several ppp(8) options are particularly helpful when used with pppoe.
enable lqr / accept lqr
Enable and accept link quality requests, which can be used to
detect whether the link has gone down.
enable mssfixup
Allow ppp(8) to adjust the maximum segment size on outgoing SYN
packets.
SEE ALSOtun(4), hostname.if(5), ifconfig(8), ppp(8), pppoe(4)
L. Mamakos, et al., RFC 2516 A Method for Transmitting PPP Over Ethernet.
For an explanation how PPPoE is further encapsulated on the way to your
ISP, and why 1454 is the optimum MTU for native IPv4 and native IPv6
connections, go to http://www.mynetwatchman.com/kb/adsl/pppoemtu.htm.
Tunneled IPv6 connections using gif(4) tunnels have an optimum MTU of
1434, the difference is just the size of an IPv4 header for the simple
encapsulation.
HISTORY
This implementation of pppoe first appeared in OpenBSD 2.8.
AUTHORS
The pppoe program was written by Jason L. Wright <jason@thought.net> of
Network Security Technologies, Inc. <http://www.netsec.net>.
BUGS
This software runs completely in user mode. As such it will have much
more overhead than pppoe(4), a kernel implementation.
The service is not currently used by the server code.
MirOS BSD #10-current June 4, 2008 2
