PERLNUMBER(1perl) Perl Programmers Reference Guide PERLNUMBER(1perl)NAMEperlnumber - semantics of numbers and numeric operations in Perl
$n = 1234; # decimal integer
$n = 0b1110011; # binary integer
$n = 01234; # octal integer
$n = 0x1234; # hexadecimal integer
$n = 12.34e-56; # exponential notation
$n = "-12.34e56"; # number specified as a string
$n = "1234"; # number specified as a string
This document describes how Perl internally handles numeric values.
Perl's operator overloading facility is completely ignored here.
Operator overloading allows user-defined behaviors for numbers, such as
operations over arbitrarily large integers, floating points numbers
with arbitrary precision, operations over "exotic" numbers such as
modular arithmetic or p-adic arithmetic, and so on. See overload for
Perl can internally represent numbers in 3 different ways: as native
integers, as native floating point numbers, and as decimal strings.
Decimal strings may have an exponential notation part, as in
"12.34e-56". Native here means "a format supported by the C compiler
which was used to build perl".
The term "native" does not mean quite as much when we talk about native
integers, as it does when native floating point numbers are involved.
The only implication of the term "native" on integers is that the
limits for the maximal and the minimal supported true integral
quantities are close to powers of 2. However, "native" floats have a
most fundamental restriction: they may represent only those numbers
which have a relatively "short" representation when converted to a
binary fraction. For example, 0.9 cannot be represented by a native
float, since the binary fraction for 0.9 is infinite:
with the sequence 1100 repeating again and again. In addition to this
limitation, the exponent of the binary number is also restricted when
it is represented as a floating point number. On typical hardware,
floating point values can store numbers with up to 53 binary digits,
and with binary exponents between -1024 and 1024. In decimal
representation this is close to 16 decimal digits and decimal exponents
in the range of -304..304. The upshot of all this is that Perl cannot
store a number like 12345678901234567 as a floating point number on
such architectures without loss of information.
Similarly, decimal strings can represent only those numbers which have
a finite decimal expansion. Being strings, and thus of arbitrary
length, there is no practical limit for the exponent or number of
decimal digits for these numbers. (But realize that what we are
discussing the rules for just the storage of these numbers. The fact
that you can store such "large" numbers does not mean that the
operations over these numbers will use all of the significant digits.
See "Numeric operators and numeric conversions" for details.)
In fact numbers stored in the native integer format may be stored
either in the signed native form, or in the unsigned native form. Thus
the limits for Perl numbers stored as native integers would typically
be -2**31..2**32-1, with appropriate modifications in the case of
64-bit integers. Again, this does not mean that Perl can do operations
only over integers in this range: it is possible to store many more
integers in floating point format.
Summing up, Perl numeric values can store only those numbers which have
a finite decimal expansion or a "short" binary expansion.
Numeric operators and numeric conversions
As mentioned earlier, Perl can store a number in any one of three
formats, but most operators typically understand only one of those
formats. When a numeric value is passed as an argument to such an
operator, it will be converted to the format understood by the
Six such conversions are possible:
native integer --> native floating point (*)
native integer --> decimal string
native floating_point --> native integer (*)
native floating_point --> decimal string (*)
decimal string --> native integer
decimal string --> native floating point (*)
These conversions are governed by the following general rules:
· If the source number can be represented in the target form, that
representation is used.
· If the source number is outside of the limits representable in the
target form, a representation of the closest limit is used. (Loss
· If the source number is between two numbers representable in the
target form, a representation of one of these numbers is used.
(Loss of information)
· In "native floating point --> native integer" conversions the
magnitude of the result is less than or equal to the magnitude of
the source. ("Rounding to zero".)
· If the "decimal string --> native integer" conversion cannot be
done without loss of information, the result is compatible with the
conversion sequence "decimal_string --> native_floating_point -->
native_integer". In particular, rounding is strongly biased to 0,
though a number like "0.99999999999999999999" has a chance of being
rounded to 1.
RESTRICTION: The conversions marked with "(*)" above involve steps
performed by the C compiler. In particular, bugs/features of the
compiler used may lead to breakage of some of the above rules.
Flavors of Perl numeric operations
Perl operations which take a numeric argument treat that argument in
one of four different ways: they may force it to one of the
integer/floating/ string formats, or they may behave differently
depending on the format of the operand. Forcing a numeric value to a
particular format does not change the number stored in the value.
All the operators which need an argument in the integer format treat
the argument as in modular arithmetic, e.g., "mod 2**32" on a 32-bit
architecture. "sprintf "%u", -1" therefore provides the same result as
"sprintf "%u", ~0".
The binary operators "+" "-" "*" "/" "%" "==" "!=" ">" "<" ">="
"<=" and the unary operators "-" "abs" and "--" will attempt to
convert arguments to integers. If both conversions are possible
without loss of precision, and the operation can be performed
without loss of precision then the integer result is used.
Otherwise arguments are converted to floating point format and the
floating point result is used. The caching of conversions (as
described above) means that the integer conversion does not throw
away fractional parts on floating point numbers.
++ "++" behaves as the other operators above, except that if it is a
string matching the format "/^[a-zA-Z]*[0-9]*\z/" the string
increment described in perlop is used.
Arithmetic operators during "use integer"
In scopes where "use integer;" is in force, nearly all the
operators listed above will force their argument(s) into integer
format, and return an integer result. The exceptions, "abs", "++"
and "--", do not change their behavior with "use integer;"
Other mathematical operators
Operators such as "**", "sin" and "exp" force arguments to floating
Arguments are forced into the integer format if not strings.
Bitwise operators during "use integer"
forces arguments to integer format. Also shift operations
internally use signed integers rather than the default unsigned.
Operators which expect an integer
force the argument into the integer format. This is applicable to
the third and fourth arguments of "sysread", for example.
Operators which expect a string
force the argument into the string format. For example, this is
applicable to "printf "%s", $value".
Though forcing an argument into a particular form does not change the
stored number, Perl remembers the result of such conversions. In
particular, though the first such conversion may be time-consuming,
repeated operations will not need to redo the conversion.
Ilya Zakharevich "email@example.com"
Editorial adjustments by Gurusamy Sarathy <gsar@ActiveState.com>
Updates for 5.8.0 by Nicholas Clark <firstname.lastname@example.org>
perl v5.18.2 2013-11-04 PERLNUMBER(1perl)