NSRSSC(8)NSRSSC(8)NAMEnsrssc - NetWorker save set consolidation program
SYNOPSISnsrssc-c client -N saveset [ -p pool ] [ -y retention ] [ -r ] [ -vq ]
DESCRIPTIONnsrssc consolidates the most recent level 1 (partial) save set and its
corresponding full-level save set into a new full-level save set. This
consolidation process effectively achieves the same outcome as a full-
level backup at the time partial backup was done.
Normally, nsrssc is invoked within savegrp(8) as part of a consolida‐
tion-level backup. During the consolidation-level backup, savegrp(8)
automatically generates a level 1 backup, then calls nsrssc to create a
consolidated backup, using the latest full-level save set.
Using nsrssc allows for greater flexibility in scheduling backups and
save set consolidation. Unlike the savegrp(8) command, which completes
a consolidation backup promptly after the level 1 backup is completed,
nsrssc allows you to schedule the consolidation at a different time.
Scheduling a time between the full backup and consolidation backup
frees up NetWorker to complete other processes.
If you execute nsrssc manually, the most recently backed-up save set
must be a level 1 save set; otherwise, the consolidation will not be
successful.
The nsrssc command requires at least two active devices. The consoli‐
dation process uses simultaneous device reads and writes to create its
consolidated save set. This mechanism creates a restriction upon the
location of the newly created save set. The new save set cannot be
created on the same volume where the partial or full save set was
derived. Also, volumes containing the previous full and level 1 save
sets must reside on the same storage node.
OPTIONS-c client
Indicates the name of the client whose save set should be
included for the consolidation process.
-N saveset
Indicates the name for the generated consolidated save set.
-p pool
Specifies the destination media pool to build the consolidated
full save set. The pool may be any pool currently registered
with nsrd(8). The selected pool must be the same pool type as
the previous full-level save set. You can view pool values by
selecting Pools from the Administration menu of networker(8).
Pool values are also listed in the NSRpool resource. See
nsr_pool(5).
If this option is omitted, then the consolidated save sets are
automatically built on volume(s) whose media pool is the same as
that of the previous full-level save set.
-r Removes the level 1 save set. If the level 1 save set is on
tape, then the save set will expire. If the level 1 save set is
on [adv_]file type volume, then the save set (including its
index entries, its media database entries, and the actual save
set data on disk) is removed. Please note that nsrssc will
never attempt to remove the level 1 if consolidation fails.
If the level 1 save set has already been cloned prior to the
consolidation, then this option is ignored and the original
level 1 save set will not expire, and it will not be removed
from [adv_]file type volume.
-v Enables verbose operation. In this mode, additional messages
may be generated during the consolidation process.
-y retention
Sets the date (in nsr_getdate(3) format) when the consolidated
data will become recyclable. The special value forever is used
to indicate that a volume that never expires (i.e. an archive
volume) must be used. By default, the server determines this
date for the save set based on the retention policies in effect.
This option allows overriding the existing policies.
-q Runs quietly. This is the default mode.
EXAMPLES
The following examples demonstrate how save set consolidation can be
performed. In both examples, a save set defined in group name elmanco
is consolidated for client delepanto. The save set data for group
elmanco is /etc and /users .
Example:
To perform a save set consolidation, use the following commands:
savegrp -l 1 -I -G elmanco
nsrssc-c delepanto -N /etc
nsrssc-c delepanto -N /users
Note that this example is almost the same as doing a savegrp -G elmanco
-l c. The only differences are:
1) No index and bootstrap is backed up after data is consolidated.
2) If there is a failure during the consolidated process, a full
backup is not performed.
Example:
To direct level 1 data to a disk cache (file-type device) and have the
level 1 save set removed after a full-level save set is built on tape,
perform the following operations:
1. Set up a pool which only accepts level 1 data and its devices are
only file type devices.
2. Run the following commands:
savegrp -G elmanco -l 1 -I
nsrssc-c delepanto -N /etc -r
nsrssc-c delepanto -N /users -r
This process removes the level 1 completely. Also, since fast media
(disk-file type) is involved, this process may be a much faster way of
generating a full-level save set when compared to doing a regular full-
level backup.
DIAGNOSTICS
On successful completion, nsrssc returns zero; otherwise, a non-zero
value is returned.
Some error codes are:
98 Failed because the level 1 and previous full are not in the same
storage node.
99 Failed, most likely due to a renamed/deleted directory condition
You may also see one of the following messages:
You are not authorized to run this command
Only root may run nsrssc
Cannot contact media database
Most likely, nsrmmd(8) is unavailable to answer queries, or an
additional NetWorker daemon may have completed processing. In
either case, the system administrator needs to determine if the
NetWorker services need to be restarted. Note, there may be a
small interval during startup when the services may be unavail‐
able to answer any queries.
SEE ALSOnsr_schedule(5), nsr_group(5), mminfo(8), savegrp(8), nsrclone(8)NetWorker 7.3.2 Aug 23, 06 NSRSSC(8)
