ledctl(8)Intel(R) Enclosure LED Control Application ledctl(8)NAMEledctl - Intel(R) LED control application for a storage enclosures.
SYNOPSISledctl [OPTIONS] pattern_name=list_of_devices ...
DESCRIPTION
The ledctl is an user space application designed to control LEDs
associated with each slot in an enclosure or a drive bay. The LEDs of
devices listed in list_of_devices are set to the given pattern
pattern_name and all other LEDs are turned off. User must have root
privileges to use this application.
There are two types of systems: 2-LEDs systems (Activity LED, Status
LED) and 3-LEDs systems (Activity LED, Locate LED, Fail LED). The
ledctl application uses SGPIO and SES-2 protocol to control LEDs. The
program implements IBPI patterns of SFF-8489 specification for SGPIO.
Please note some enclosures do not stick close to SFF-8489
specification. It might happen that enclosure's processor will accept
an IBPI pattern but it will blink the LEDs at variance with SFF-8489
specification or it has limited number of patterns supported.
LED management (AHCI) and SAF-TE protocols are not supported.
The ledctl application has been verified to work with Intel(R) storage
controllers (i.e. Intel(R) AHCI controller and Intel(R) SAS
controller). The application might work with storage controllers of
other vendors (especially SCSI/SAS controllers). However, storage
controllers of other vendors have not been tested.
The ledmon application has the highest priority when accessing LEDs.
It means that some patterns set by ledctl may have no effect if ledmon
is running (except Locate pattern).
The ledctl application is a part of Intel(R) Enclosure LED Utilities.
Pattern Names
The ledctl application accepts the following names for pattern_name
argument according to SFF-8489 specification.
locate Turns Locate LED associated with the given device(s) or empty
slot(s) on.
locate_off
Turns only Locate LED off.
normal Turns Status LED, Failure LED and Locate LED off.
off Turns only Status LED and Failure LED off.
ica or degraded
Visualizes "In a Critical Array" pattern.
rebuild or rebuild_p
Visualizes "Rebuild" pattern.
ifa or failed_array
Visualizes "In a Failed Array" pattern.
hotspare
Visualizes "Hotspare" pattern.
pfa Visualizes "Predicted Failure Analysis" pattern.
failure or disk_failed
Visualizes "Failure" pattern.
ses_abort
SES-2 R/R ABORD
ses_rebuild
SES-2 REBUILD/REMAP
ses_ifa SES-2 IN FAILED ARRAY
ses_ica SES-2 IN CRIT ARRAY
ses_cons_check
SES-2 CONS CHECK
ses_hotspare
SES-2 HOT SPARE
ses_rsvd_dev
SES-2 RSVD DEVICE
ses_ok SES-2 OK
ses_ident
SES-2 IDENT
ses_rm SES-2 REMOVE
ses_insert
SES-2 INSERT
ses_missing
SES-2 MISSING
ses_dnr SES-2 DO NOT REMOVE
ses_active
SES-2 ACTIVE
ses_enbale_bb
SES-2 ENABLE BYP B
ses_enable_ba
SES-2 ENABLE BYP A
ses_devoff
SES-2 DEVICE OFF
ses_fault
SES-2 FAULT
Patterns Translation
When non SES-2 pattern is send to device in enclosure automatic
translation is being done.
locate
locate is translated to ses_ident
locate_off
locate_off is translated to ~ses_ident
normal
normal is translated to ses_ok
off off is translated to ses_ok
degraded
degraded is translated to ses_ica
rebuild
rebuild is translated to ses_rebuild
rebuild_p
rebuild_p is translated to ses_rebuild
failed
failed is translated to ses_ifa
hotspare
hotspare is translated to ses_hotspare
pfa pfa is translated to ses_rsvd_dev
failure
failure is translated to ses_fault
disk_failed
disk_failed is translated to ses_fault
List of Devices
The application accepts a list of devices in two formats. The first
format is a list with comma separated elements. The second format is
a list in curly braces and elements are separated by space. See
examples section bellow for details.
A device is a path to file in /dev directory or in /sys/block
directory. It may identify a block device, a RAID device or a
container device. In case of a RAID device or a container device a
state will be set for all block devices associated, respectively.
The LEDs of devices listed in list_of_devices are set to the given
pattern pattern_name and all other LEDs are turned off.
OPTIONS-c or --config=path
Sets a path to local configuration file. If this option is
specified the global configuration file and user configuration
file has no effect.
-l or --log=path
Sets a path to local log file. If this option is specified the
global log file /var/log/ledctl.log is not used.
--quiet Turns off all messages sent to "stdout" or "stderr" out. The
messages will be still logged to local file and syslog
facility.
-h or --help
Prints this text out and exits.
-v or --version
Displays version of ledctl and information about the license
and exits.
FILES
/var/log/ledctl.log
Global log file, used by all instances of ledctl application.
To force logging to user defined file use -l option switch.
~/.ledctl
User configuration file, shared between ledmon and all ledctl
application instances.
/etc/ledcfg.conf
Global configuration file, shared between ledmon and all ledctl
application instances.
EXAMPLES
The following example illustrates how to locate a single block device.
ledctl locate=/dev/sda
The following example illustrates how to turn Locate LED off for the
same block device.
ledctl locate_off=/dev/sda
The following example illustrates how to locate disks of a RAID device
and how to set rebuild pattern for two block devices at the same time.
This example uses both formats of device list.
ledctl locate=/dev/md127 rebuild={ /sys/block/sd[a-b] }
The following example illustrates how to turn Status LED and Failure
LED off for the given device(s).
ledctl off={ /dev/sda /dev/sdb }
The following example illustrates how to locate a three block devices.
This example uses the first format of device list.
ledctl locate=/dev/sda,/dev/sdb,/dev/sdc
LICENSE
Copyright (c) 2009-2013 Intel Corporation.
This program is distributed under the terms of the GNU General Public
License as published by the Free Software Foundation. See the built-in
help for details on the License and the lack of warranty.
SEE ALSOledmon(8), ledctl.conf(5)AUTHOR
This manual page was written by Artur Wojcik <artur.wojcik@intel.com>.
It may be used by others.
POD ERRORS
Hey! The above document had some coding errors, which are explained
below:
Around line 182:
'=item' outside of any '=over'
LEDCTL Version 0.75 December 2012 ledctl(8)
