ipmipower(8) System Commands ipmipower(8)NAMEipmipower - IPMI power control utility
SYNOPSISipmipower [OPTION...]
DESCRIPTIONipmipower allows users to remotely power on, off, cycle, hard reset,
get a power status query, perform a pulse diagnostic interrupt, or ini‐
tiate a soft-shutdown of the OS via ACPI through the IPMI over LAN pro‐
tocol.
When a power command (--on, --off, --cycle, --reset, --stat, --pulse,
or --soft) is specified on the command line, ipmipower will attempt to
run the power command on all hostnames listed on the command line then
exit.
If no power commands are specified on the command line, ipmipower will
run in interactive mode. Interactive mode gives the user a command line
interface to enter various commands. Details of the interactive command
line interface can be found below under INTERACTIVE COMMANDS.
Listed below are general IPMI options, tool specific options, trouble
shooting information, workaround information, examples, and known
issues. For a general introduction to FreeIPMI please see freeipmi(7).
GENERAL OPTIONS
The following options are general options for configuring IPMI communi‐
cation and executing general tool commands.
-D IPMIDRIVER, --driver-type=IPMIDRIVER
Specify the driver type to use instead of doing an auto selec‐
tion. The currently available outofband drivers are LAN and
LAN_2_0, which perform IPMI 1.5 and IPMI 2.0 respectively.
-h IPMIHOST1,IPMIHOST2,..., --hostname=IPMIHOST1[:PORT],IPMI‐
HOST2[:PORT],...
Specify the remote host(s) to communicate with. Multiple host‐
names may be separated by comma or may be specified in a range
format; see HOSTRANGED SUPPORT below. An optional port can be
specified with each host, which may be useful in port forwarding
or similar situations.
-u USERNAME, --username=USERNAME
Specify the username to use when authenticating with the remote
host. If not specified, a null (i.e. anonymous) username is
assumed. The user must have atleast OPERATOR privileges to run
the --on, --off, --reset, --cycle, --pulse, or --soft power con‐
trol commands. The user must have atleast USER privileges to
determine the power status of the machine through --stat.
-p PASSWORD, --password=PASSWORD
Specify the password to use when authenticationg with the remote
host. If not specified, a null password is assumed. Maximum
password length is 16 for IPMI 1.5 and 20 for IPMI 2.0.
-P, --password-prompt
Prompt for password to avoid possibility of listing it in
process lists.
-k K_G, --k-g=K_G
Specify the K_g BMC key to use when authenticating with the
remote host for IPMI 2.0. If not specified, a null key is
assumed. To input the key in hexadecimal form, prefix the string
with '0x'. E.g., the key 'abc' can be entered with the either
the string 'abc' or the string '0x616263'
-K, --k-g-prompt
Prompt for k-g to avoid possibility of listing it in process
lists.
--session-timeout=MILLISECONDS
Specify the session timeout in milliseconds. Defaults to 20000
milliseconds (20 seconds) if not specified.
--retransmission-timeout=MILLISECONDS
Specify the packet retransmission timeout in milliseconds.
Defaults to 400 milliseconds (0.4 seconds) if not specified.
-a AUTHENTICATION-TYPE, --authentication-type=AUTHENTICATION-TYPE
Specify the IPMI 1.5 authentication type to use. The currently
available authentication types are NONE, STRAIGHT_PASSWORD_KEY,
MD2, and MD5. Defaults to MD5 if not specified.
-I CIPHER-SUITE-ID, --cipher-suite-id=CIPHER-SUITE-ID
Specify the IPMI 2.0 cipher suite ID to use. The Cipher Suite ID
identifies a set of authentication, integrity, and confidential‐
ity algorithms to use for IPMI 2.0 communication. The authenti‐
cation algorithm identifies the algorithm to use for session
setup, the integrity algorithm identifies the algorithm to use
for session packet signatures, and the confidentiality algorithm
identifies the algorithm to use for payload encryption. Defaults
to cipher suite ID 3 if not specified. The following cipher
suite ids are currently supported:
0 - Authentication Algorithm = None; Integrity Algorithm = None;
Confidentiality Algorithm = None
1 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm =
None; Confidentiality Algorithm = None
2 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm =
HMAC-SHA1-96; Confidentiality Algorithm = None
3 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm =
HMAC-SHA1-96; Confidentiality Algorithm = AES-CBC-128
6 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
None; Confidentiality Algorithm = None
7 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
HMAC-MD5-128; Confidentiality Algorithm = None
8 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
HMAC-MD5-128; Confidentiality Algorithm = AES-CBC-128
11 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
MD5-128; Confidentiality Algorithm = None
12 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =
MD5-128; Confidentiality Algorithm = AES-CBC-128
15 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm
= None; Confidentiality Algorithm = None
16 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm
= HMAC_SHA256_128; Confidentiality Algorithm = None
17 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm
= HMAC_SHA256_128; Confidentiality Algorithm = AES-CBC-128
-l PRIVILEGE-LEVEL, --privilege-level=PRIVILEGE-LEVEL
Specify the privilege level to be used. The currently available
privilege levels are USER, OPERATOR, and ADMIN. Defaults to
OPERATOR if not specified.
--config-file=FILE
Specify an alternate configuration file.
-W WORKAROUNDS, --workaround-flags=WORKAROUNDS
Specify workarounds to vendor compliance issues. Multiple work‐
arounds can be specified separated by commas. A special command
line flag of "none", will indicate no workarounds (may be useful
for overriding configured defaults). See WORKAROUNDS below for a
list of available workarounds.
--debug
Turn on debugging.
-?, --help
Output a help list and exit.
--usage
Output a usage message and exit.
-V, --version
Output the program version and exit.
IPMIPOWER OPTIONS
The following options are specific to ipmipower.
-n, --on
Power on the target hosts.
-f, --off
Power off the target hosts.
-c, --cycle
Power cycle the target hosts.
-r, --reset
Reset the target hosts.
-s, --stat
Get power status of the target hosts.
--pulse
Send power diagnostic interrupt to target hosts.
--soft Initiate a soft-shutdown of the OS via ACPI.
--on-if-off
The IPMI specification does not require the power cycle or hard
reset commands to turn on a machine that is currently powered
off. This option will force ipmipower to issue a power on com‐
mand instead of a power cycle or hard reset command if the
remote machine's power is currently off.
--wait-until-on
The IPMI specification allows power on commands to return prior
to the power on actually taking place. This option will force
ipmipower to regularly query the remote BMC and return only
after the machine has powered on.
--wait-until-off
The IPMI specification allows power off commands to return prior
the power off actually taking place. This option will force
ipmipower to regularly query the remote BMC and return only
after the machine has powered off.
--oem-power-type=OEM-POWER-TYPE
This option informs ipmipower to initiate power control opera‐
tions via an IPMI OEM specific power control extension. The cur‐
rently available POWERTYPEs are NONE and C410X. Please see OEM
POWER EXTENSIONS below for additional information.
IPMIPOWER ADVANCED NETWORK OPTIONS
The following options are used to change the networking behavior of
ipmipower.
--retransmission-wait-timeout=MILLISECONDS
Specify the retransmission wait timeout length in milliseconds.
The retransmission wait timeout is similar to the retransmission
timeout above, but is used specifically for power completion
verification with the --wait-until-on and --wait-until-off
options. Defaults to 500 milliseconds (0.5 seconds).
--retransmission-backoff-count=COUNT
Specify the retransmission backoff count for retransmissions.
After ever COUNT retransmissions, the retransmission timeout
length will be increased by another factor. Defaults to 8.
--ping-interval=MILLISECONDS
Specify the ping interval length in milliseconds. When running
in interactive mode, RMCP (Remote Management Control Protocol)
discovery messages will be sent to all configured remote hosts
every MILLISECONDS to confirm their support of IPMI. Power com‐
mands cannot be sent to a host until it is discovered (or re-
discovered if previously lost). Defaults to 5000 milliseconds (5
seconds). Ping discovery messages can be disabled by setting
this valu to 0. RMCP ping discovery messages are automatically
disabled in non-interactive mode.
--ping-timeout=MILLISECONDS
Specify the ping timeout length in milliseconds. When running in
interactive mode, RMCP (Remote Management Control Protocol) mes‐
sages discovery will be sent to all configured remote hosts to
confirm their support of IPMI. A remote host is considered
undiscovered if the host does not respond in MILLISECONDS time.
Defaults to 30000 milliseconds (30 seconds). The ping timeout
cannot be larger than the ping interval.
--ping-packet-count=COUNT
Specify the ping packet count size. Defaults to 10. See the
--ping-percent-fR option below for more information on this
option.
--ping-percent=PERCENT
Specify the ping percent value. Defaults to 50. Since IPMI is
based on UDP, it is difficult for ipmipower to distinguish
between a missing machine and a bad (or heavily loaded) network
connection in interactive mode. when running in interactive
mode. For example, suppose a link consistently drops 80% of the
packets to a particular machine. The power control operation may
have difficulty completing, although a recent pong response from
RMCP makes ipmipower believe the machine is up and functioning
properly. The ping packet acount and percent options are used
to alleviate this problem. Ipmipower will monitor RMCP ping
packets in packet count chunks. If ipmipower does not receive a
response to greater than ping percent of those packets,
ipmipower will assume the link to this node is bad and will not
send power control operations to that node until the connection
is determined to be reliable. This heuristic can be disabled by
setting either the ping packet count or ping percent to 0. This
feature is not used if ping interval is set to 0.
--ping-consec-count=COUNT
Specify the ping consecutive count. This is another heuristic
used to determine if a node should be considered discovered,
undiscovered, or with a bad connection. If a valid RMCP pong
response was received for the last COUNT ping packets, a node
will be considered discovered, regardless of other heuristics
listed above. Defaults to 5. This heuristic can be disabled by
setting this value to 0. This feature is not used if other ping
features described above are disabled.
HOSTRANGED OPTIONS
The following options manipulate hostranged output. See HOSTRANGED SUP‐
PORT below for additional information on hostranges.
-B, --buffer-output
Buffer hostranged output. For each node, buffer standard output
until the node has completed its IPMI operation. When specifying
this option, data may appear to output slower to the user since
the the entire IPMI operation must complete before any data can
be output. See HOSTRANGED SUPPORT below for additional informa‐
tion.
-C, --consolidate-output
Consolidate hostranged output. The complete standard output from
every node specified will be consolidated so that nodes with
identical output are not output twice. A header will list those
nodes with the consolidated output. When this option is speci‐
fied, no output can be seen until the IPMI operations to all
nodes has completed. If the user breaks out of the program
early, all currently consolidated output will be dumped. See
HOSTRANGED SUPPORT below for additional information.
-F NUM, --fanout=NUM
Specify multiple host fanout. Indicates the maximum number of
power control operations that can be executed in parallel.
-E, --eliminate
Eliminate hosts determined as undetected by ipmidetect. This
attempts to remove the common issue of hostranged execution tim‐
ing out due to several nodes being removed from service in a
large cluster. The ipmidetectd daemon must be running on the
node executing the command.
--always-prefix
Always prefix output, even if only one host is specified or com‐
municating in-band. This option is primarily useful for script‐
ing purposes. Option will be ignored if specified with the -C
option.
INTERACTIVE COMMANDSipmipower provides the following interactive commands at the ipmipower>
prompt. Before any power commands (on, off, cycle, reset, stat, pulse,
or soft) can be used, hostnames must be configured into ipmipower,
either through the command prompt or the hostname command below. The
parameters and options to the commands below mirror their appropriate
command line options.
hostname [IPMIHOST(s)]
Specify a new set of hosts. No input to unconfigure all hosts.
username [USERNAME]
Specify a new username. No input for null username.
password [PASSWORD]
Specify a new password. No input for null password.
k_g [K_G]
Specify a new K_g BMC Key. No input for null key. Prefix with
'0x' to enter a key in hexadecimal
ipmi-version IPMIVERSION
Specify the ipmi version to use.
session-timeout MILLISECONDS
Specify a new session timeout length.
retransmission-timeout MILLISECONDS
Specify a new retransmiision timeout length.
authentication-type AUTHENTICATION-TYPE
Specify the authentication type to use.
cipher-suite-id CIPHER-SUITE-ID
Specify the cipher suite id to use.
privilege-level PRIVILEGE-LEVEL
Specify the privilege level to use.
workaround-flags WORKAROUNDS
Specify workaround flags.
debug [on|off]
Toggle debug output.
on [IPMIHOST(s)]
Turn on all configured hosts or specified hosts.
off [IPMIHOST(s)]
Turn off all configured hosts or specified hosts.
cycle [IPMIHOST(s)]
Power cycle all configured hosts or specified hosts.
reset [IPMIHOST(s)]
Reset all configured hosts or specified hosts.
stat [IPMIHOST(s)]
Query power status for all configured hosts or specified hosts.
pulse [IPMIHOST(s)]
Pulse diagnostic interrupt all configured hosts or specified
hosts.
soft [IPMIHOST(s)]
Initiate a soft-shutdown for all configured hosts or specified
hosts.
identify-on [IPMIHOST(s)]
Turn on physical system identification.
identify-off [IPMIHOST(s)]
Turn off physical system identification.
identify-status [IPMIHOST(s)]
Query physical system identification status.
on-if-off [on|off]
Toggle on-if-off functionality.
wait-until-on [on|off]
Toggle wait-until-on functionality.
wait-until-off [on|off]
Toggle wait-until-off functionality.
retransmission-wait-timeout MILLISECONDS
Specify a new retransmission wait timeout length.
retransmission-backoff-count COUNT
Specify a new retransmission backoff count.
ping-interval MILLISECONDS
Specify a new ping interval length.
ping-timeout MILLISECONDS
Specify a new ping timeout length.
ping-packet-count COUNT
Specify a new ping packet count.
ping-percent PERCENT
Specify a new ping percent.
ping-consec-count COUNT
Specify a new ping consec count.
buffer-output [on|off]
Toggle buffer-output functionality.
consolidate-output [on|off]
Toggle consolidate-output functionality.
fanout COUNT
Specify a fanout.
always-prefix [on|off]
Toggle always-prefix functionality.
help Output help menu.
version
Output version.
config Output the current configuration.
quit Quit program. ipmipower.
OEM POWER EXTENSIONS
Some motherboards include IPMI OEM extensions for alternate power con‐
trol mechanisms. For example, these power control mechanisms may allow
you to power control a sub-device within the system rather than the
entire system itself.
By specifying an OEM power type via --oem-power-type on the command
line or freeipmi.conf(5), you can instruct ipmipower to execute alter‐
nate power control implementations over the standard ones. Depending on
the OEM extension, some power control commands may no longer be avail‐
able. For example, an OEM extension may allow on but not cycle. Spe‐
cific ipmipower options may not longer function either.
Some OEM extensions may require additional arguments for their power
control action, such as a sub-device identifier. Additional arguments
can be provided by appending a plus sign ('+') and the extra informa‐
tion to the end of the hostname. This can be done on the command line
or in interactive mode. For example, the hostname mynode+18 would indi‐
cate the power control operation should be sent to the host mynode, and
18 is the identifier of a possible sub-device to be power controlled.
The --consolidate-output option is commonly disabled when using an OEM
power control that requires extra arguments.
Because OEM power control may involve subtypes, it is possible a user
may wish to power control multiple sub-devices on the same host. For
example, you might specify the hosts mynode+1,mynode+2, indicating to
power control subdevice 1 and 2 on mynode. Because many BMCs cannot
handle multiple IPMI sessions, power control operations to the same
host will be serialized internally by ipmipower.
The following are the current OEM power types available, along with
information on the systems they work with and the power control opera‐
tions available.
C410X This OEM power type supports the power control of PCIe slots on
Dell Poweredge C410x systems. It supports on, off, and stat. The
PCIe slot number ranges from 1-16 and must always be specified
when attempting to power control with this extension. For exam‐
ple, the hostname mynode+2 would inform ipmipower to operate on
slot number 2 on mynode. The C410x appears to have difficulty
handling new slot power control requests until prior ones have
completed. Users may wish to strongly consider using the
--wait-until-on and --wait-until-off options if multiple slots
will be power controlled in short succession.
NONE This informs ipmipower that no OEM power type extension is to be
used and standard IPMI power control is used. This is the
default.
HOSTRANGED SUPPORT
Multiple hosts can be input either as an explicit comma separated lists
of hosts or a range of hostnames in the general form: prefix[n-m,l-
k,...], where n < m and l < k, etc. The later form should not be con‐
fused with regular expression character classes (also denoted by []).
For example, foo[19] does not represent foo1 or foo9, but rather repre‐
sents a degenerate range: foo19.
This range syntax is meant only as a convenience on clusters with a
prefixNN naming convention and specification of ranges should not be
considered necessary -- the list foo1,foo9 could be specified as such,
or by the range foo[1,9].
Some examples of range usage follow:
foo[01-05] instead of foo01,foo02,foo03,foo04,foo05
foo[7,9-10] instead of foo7,foo9,foo10
foo[0-3] instead of foo0,foo1,foo2,foo3
As a reminder to the reader, some shells will interpret brackets ([ and
]) for pattern matching. Depending on your shell, it may be necessary
to enclose ranged lists within quotes.
When multiple hosts are specified by the user, a socket will be created
for each host and polled on, effectively allowing communication to all
hosts in parallel. This will allow communication to large numbers of
nodes far more quickly than if done in serial. The -F option can con‐
figure the number of nodes that can be communicated with in parallel at
the same time.
By default, standard output from each node specified will be output
with the hostname prepended to each line. Although this output is read‐
able in many situations, it may be difficult to read in other situa‐
tions. For example, output from multiple nodes may be mixed together.
The -B and -C options can be used to change this default.
EXAMPLES
Determine the power status of foo[0-2] with null username and password
ipmipower-h foo[0-2] --stat
Determine the power status of foo[0-2] with non-null username and pass‐
word
ipmipower-h foo[0-2] -u foo -p bar --stat
Hard reset nodes foo[0-2] with non-null username and password
ipmipower-h foo[0-2] -u foo -p bar --reset
GENERAL TROUBLESHOOTING
Most often, IPMI problems are due to configuration problems.
IPMI over LAN problems involve a misconfiguration of the remote
machine's BMC. Double check to make sure the following are configured
properly in the remote machine's BMC: IP address, MAC address, subnet
mask, username, user enablement, user privilege, password, LAN privi‐
lege, LAN enablement, and allowed authentication type(s). For IPMI 2.0
connections, double check to make sure the cipher suite privilege(s)
and K_g key are configured properly. The bmc-config(8) tool can be used
to check and/or change these configuration settings.
In addition to the troubleshooting tips below, please see WORKAROUNDS
below to also if there are any vendor specific bugs that have been dis‐
covered and worked around.
Listed below are many of the common issues for error messages. For
additional support, please e-mail the <freeipmi-users@gnu.org> mailing
list.
"username invalid" - The username entered (or a NULL username if none
was entered) is not available on the remote machine. It may also be
possible the remote BMC's username configuration is incorrect.
"password invalid" - The password entered (or a NULL password if none
was entered) is not correct. It may also be possible the password for
the user is not correctly configured on the remote BMC.
"password verification timeout" - Password verification has timed out.
A "password invalid" error (described above) or a generic "session
timeout" (described below) occurred. During this point in the protocol
it cannot be differentiated which occurred.
"k_g invalid" - The K_g key entered (or a NULL K_g key if none was
entered) is not correct. It may also be possible the K_g key is not
correctly configured on the remote BMC.
"privilege level insufficient" - An IPMI command requires a higher user
privilege than the one authenticated with. Please try to authenticate
with a higher privilege. This may require authenticating to a different
user which has a higher maximum privilege.
"privilege level cannot be obtained for this user" - The privilege
level you are attempting to authenticate with is higher than the maxi‐
mum allowed for this user. Please try again with a lower privilege. It
may also be possible the maximum privilege level allowed for a user is
not configured properly on the remote BMC.
"authentication type unavailable for attempted privilege level" - The
authentication type you wish to authenticate with is not available for
this privilege level. Please try again with an alternate authentication
type or alternate privilege level. It may also be possible the avail‐
able authentication types you can authenticate with are not correctly
configured on the remote BMC.
"cipher suite id unavailable" - The cipher suite id you wish to authen‐
ticate with is not available on the remote BMC. Please try again with
an alternate cipher suite id. It may also be possible the available
cipher suite ids are not correctly configured on the remote BMC.
"ipmi 2.0 unavailable" - IPMI 2.0 was not discovered on the remote
machine. Please try to use IPMI 1.5 instead.
"connection timeout" - Initial IPMI communication failed. A number of
potential errors are possible, including an invalid hostname specified,
an IPMI IP address cannot be resolved, IPMI is not enabled on the
remote server, the network connection is bad, etc. Please verify con‐
figuration and connectivity.
"session timeout" - The IPMI session has timed out. Please reconnect.
If this error occurs often, you may wish to increase the retransmission
timeout. Some remote BMCs are considerably slower than others.
IPMIPOWER TROUBLESHOOTING
When powering on a powered off machine, the client must have a means by
which to resolve the MAC address of the remote machine's ethernet card.
While most modern IPMI solutions support the ability to ARP and resolve
addresses when the machine is powered off, some older machines do not.
This is typically solved in one of two ways:
1) Enable gratuitous ARPs on the remote machine. The remote machine
will send out a gratuitous ARP, which advertises the ethernet IP and
MAC address so that other machines on the network this information
their local ARP cache. For large clusters, this method is not recom‐
mended since gratuitous ARPs can flood the network with unnecessary
traffic.
2) Permanently store the remote machine's MAC address in the local ARP
cache. This is the more common approach on large clusters.
Other methods are listed in the IPMI specification.
WORKAROUNDS
With so many different vendors implementing their own IPMI solutions,
different vendors may implement their IPMI protocols incorrectly. The
following describes a number of workarounds currently available to han‐
dle discovered compliance issues. When possible, workarounds have been
implemented so they will be transparent to the user. However, some will
require the user to specify a workaround be used via the -W option.
The hardware listed below may only indicate the hardware that a problem
was discovered on. Newer versions of hardware may fix the problems
indicated below. Similar machines from vendors may or may not exhibit
the same problems. Different vendors may license their firmware from
the same IPMI firmware developer, so it may be worthwhile to try work‐
arounds listed below even if your motherboard is not listed.
If you believe your hardware has an additional compliance issue that
needs a workaround to be implemented, please contact the FreeIPMI main‐
tainers on <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
authcap - This workaround flag will skip early checks for username
capabilities, authentication capabilities, and K_g support and allow
IPMI authentication to succeed. It works around multiple issues in
which the remote system does not properly report username capabilities,
authentication capabilities, or K_g status. Those hitting this issue
may see "username invalid", "authentication type unavailable for
attempted privilege level", or "k_g invalid" errors. Issue observed on
Asus P5M2/P5MT-R/RS162-E4/RX4, Intel SR1520ML/X38ML, and Sun Fire
2200/4150/4450 with ELOM.
idzero - This workaround flag will allow empty session IDs to be
accepted by the client. It works around IPMI sessions that report empty
session IDs to the client. Those hitting this issue may see "session
timeout" errors. Issue observed on Tyan S2882 with M3289 BMC.
unexpectedauth - This workaround flag will allow unexpected non-null
authcodes to be checked as though they were expected. It works around
an issue when packets contain non-null authentication data when they
should be null due to disabled per-message authentication. Those hit‐
ting this issue may see "session timeout" errors. Issue observed on
Dell PowerEdge 2850,SC1425. Confirmed fixed on newer firmware.
forcepermsg - This workaround flag will force per-message authentica‐
tion to be used no matter what is advertised by the remote system. It
works around an issue when per-message authentication is advertised as
disabled on the remote system, but it is actually required for the pro‐
tocol. Those hitting this issue may see "session timeout" errors.
Issue observed on IBM eServer 325.
endianseq - This workaround flag will flip the endian of the session
sequence numbers to allow the session to continue properly. It works
around IPMI 1.5 session sequence numbers that are the wrong endian.
Those hitting this issue may see "session timeout" errors. Issue
observed on some Sun ILOM 1.0/2.0 (depends on service processor
endian).
noauthcodecheck - This workaround flag will tell FreeIPMI to not check
the authentication codes returned from IPMI 1.5 command responses. It
works around systems to return invalid authentication codes due to
hashing or implementation errors. Users are cautioned on the use of
this option, as it removes an authentication check verifying the valid‐
ity of a packet. However, in most organizations, this is unlikely to be
a security issue. Those hitting this issue may see "connection time‐
out", "session timeout", or "password verification timeout" errors.
Issue observed on Xyratex FB-H8-SRAY.
intel20 - This workaround flag will work around several Intel IPMI 2.0
authentication issues. The issues covered include padding of usernames,
and password truncation if the authentication algorithm is HMAC-
MD5-128. Those hitting this issue may see "username invalid", "password
invalid", or "k_g invalid" errors. Issue observed on Intel SE7520AF2
with Intel Server Management Module (Professional Edition).
supermicro20 - This workaround flag will work around several Supermicro
IPMI 2.0 authentication issues on motherboards w/ Peppercon IPMI
firmware. The issues covered include handling invalid length authenti‐
cation codes. Those hitting this issue may see "password invalid"
errors. Issue observed on Supermicro H8QME with SIMSO daughter card.
Confirmed fixed on newerver firmware.
sun20 - This workaround flag will work work around several Sun IPMI 2.0
authentication issues. The issues covered include invalid lengthed hash
keys, improperly hashed keys, and invalid cipher suite records. Those
hitting this issue may see "password invalid" or "bmc error" errors.
Issue observed on Sun Fire 4100/4200/4500 with ILOM. This workaround
automatically includes the "opensesspriv" workaround.
opensesspriv - This workaround flag will slightly alter FreeIPMI's IPMI
2.0 connection protocol to workaround an invalid hashing algorithm used
by the remote system. The privilege level sent during the Open Session
stage of an IPMI 2.0 connection is used for hashing keys instead of the
privilege level sent during the RAKP1 connection stage. Those hitting
this issue may see "password invalid", "k_g invalid", or "bad rmcpplus
status code" errors. Issue observed on Sun Fire 4100/4200/4500 with
ILOM, Inventec 5441/Dell Xanadu II, Supermicro X8DTH, Supermicro X8DTG,
Intel S5500WBV/Penguin Relion 700, Intel S2600JF/Appro 512X, and Quanta
QSSC-S4R//Appro GB812X-CN. This workaround is automatically triggered
with the "sun20" workaround.
integritycheckvalue - This workaround flag will work around an invalid
integrity check value during an IPMI 2.0 session establishment when
using Cipher Suite ID 0. The integrity check value should be 0 length,
however the remote motherboard responds with a non-empty field. Those
hitting this issue may see "k_g invalid" errors. Issue observed on
Supermicro X8DTG, Supermicro X8DTU, and Intel S5500WBV/Penguin Relion
700, and Intel S2600JF/Appro 512X.
No IPMI 1.5 Support - Some motherboards that support IPMI 2.0 have been
found to not support IPMI 1.5. Those hitting this issue may see "ipmi
2.0 unavailable" or "connection timeout" errors. This issue can be
worked around by using IPMI 2.0 instead of IPMI 1.5 by specifying
--driver-address=LAN_2_0. Issue observed on HP Proliant DL 145.
DIAGNOSTICS
Upon successful execution, exit status is 0. On error, exit status is
1.
If multiple hosts are specified for communication, the exit status is 0
if and only if all targets successfully execute. Otherwise the exit
status is 1.
When operating in interactive mode, the exit value will be based on the
last power operation executed.
KNOWN ISSUES
On older operating systems, if you input your username, password, and
other potentially security relevant information on the command line,
this information may be discovered by other users when using tools like
the ps(1) command or looking in the /proc file system. It is generally
more secure to input password information with options like the -P or
-K options. Configuring security relevant information in the FreeIPMI
configuration file would also be an appropriate way to hide this infor‐
mation.
In order to prevent brute force attacks, some BMCs will temporarily
"lock up" after a number of remote authentication errors. You may need
to wait awhile in order to this temporary "lock up" to pass before you
may authenticate again.
IPMI specifications do not require BMCs to perform a power control
operation before returning a completion code to the caller. Therefore,
it is possible for ipmipower to return power status queries opposite of
what you are expecting. For example, if a "power off" operation is
performed, a BMC may return a successful completion code to ipmipower
before the "power off" operation is actually performed. Subsequent
power status queries may return "on" for several seconds, until the BMC
actually performs the "power off" operation.
REPORTING BUGS
Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
COPYRIGHT
Copyright (C) 2007-2012 Lawrence Livermore National Security, LLC.
Copyright (C) 2003-2007 The Regents of the University of California.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 3 of the License, or (at your
option) any later version.
SEE ALSOfreeipmi.conf(5), freeipmi(7), bmc-config(8), ipmi-oem(8)
http://www.gnu.org/software/freeipmi/
ipmipower 1.2.1 2013-11-21 ipmipower(8)
