IP6TABLES(8) iptables 1.4.4 IP6TABLES(8)NAMEip6tables - IPv6 packet filter administration
SYNOPSISip6tables [-t table] {-A|-D} chain rule-specification [options...]
ip6tables [-t table] -I chain [rulenum] rule-specification [options...]
ip6tables [-t table] -R chain rulenum rule-specification [options...]
ip6tables [-t table] -D chain rulenum [options...]
ip6tables [-t table] -S [chain [rulenum]]
ip6tables [-t table] {-F|-L|-Z} [chain] [options...]
ip6tables [-t table] -N chain
ip6tables [-t table] -X [chain]
ip6tables [-t table] -P chain target [options...]
ip6tables [-t table] -E old-chain-name new-chain-name
DESCRIPTION
Ip6tables is used to set up, maintain, and inspect the tables of IPv6
packet filter rules in the Linux kernel. Several different tables may
be defined. Each table contains a number of built-in chains and may
also contain user-defined chains.
Each chain is a list of rules which can match a set of packets. Each
rule specifies what to do with a packet that matches. This is called a
`target', which may be a jump to a user-defined chain in the same ta‐
ble.
TARGETS
A firewall rule specifies criteria for a packet and a target. If the
packet does not match, the next rule in the chain is the examined; if
it does match, then the next rule is specified by the value of the tar‐
get, which can be the name of a user-defined chain or one of the spe‐
cial values ACCEPT, DROP, QUEUE or RETURN.
ACCEPT means to let the packet through. DROP means to drop the packet
on the floor. QUEUE means to pass the packet to userspace. (How the
packet can be received by a userspace process differs by the particular
queue handler. 2.4.x and 2.6.x kernels up to 2.6.13 include the
ip_queue queue handler. Kernels 2.6.14 and later additionally include
the nfnetlink_queue queue handler. Packets with a target of QUEUE will
be sent to queue number '0' in this case. Please also see the NFQUEUE
target as described later in this man page.) RETURN means stop
traversing this chain and resume at the next rule in the previous
(calling) chain. If the end of a built-in chain is reached or a rule
in a built-in chain with target RETURN is matched, the target specified
by the chain policy determines the fate of the packet.
TABLES
There are currently three independent tables (which tables are present
at any time depends on the kernel configuration options and which mod‐
ules are present).
-t, --table table
This option specifies the packet matching table which the com‐
mand should operate on. If the kernel is configured with auto‐
matic module loading, an attempt will be made to load the appro‐
priate module for that table if it is not already there.
The tables are as follows:
filter:
This is the default table (if no -t option is passed). It
contains the built-in chains INPUT (for packets destined to
local sockets), FORWARD (for packets being routed through
the box), and OUTPUT (for locally-generated packets).
mangle:
This table is used for specialized packet alteration. Until
kernel 2.4.17 it had two built-in chains: PREROUTING (for
altering incoming packets before routing) and OUTPUT (for
altering locally-generated packets before routing). Since
kernel 2.4.18, three other built-in chains are also sup‐
ported: INPUT (for packets coming into the box itself), FOR‐
WARD (for altering packets being routed through the box),
and POSTROUTING (for altering packets as they are about to
go out).
raw:
This table is used mainly for configuring exemptions from
connection tracking in combination with the NOTRACK target.
It registers at the netfilter hooks with higher priority and
is thus called before ip_conntrack, or any other IP tables.
It provides the following built-in chains: PREROUTING (for
packets arriving via any network interface) OUTPUT (for
packets generated by local processes)
OPTIONS
The options that are recognized by ip6tables can be divided into sev‐
eral different groups.
COMMANDS
These options specify the specific action to perform. Only one of them
can be specified on the command line unless otherwise specified below.
For all the long versions of the command and option names, you need to
use only enough letters to ensure that ip6tables can differentiate it
from all other options.
-A, --append chain rule-specification
Append one or more rules to the end of the selected chain. When
the source and/or destination names resolve to more than one
address, a rule will be added for each possible address combina‐
tion.
-D, --delete chain rule-specification
-D, --delete chain rulenum
Delete one or more rules from the selected chain. There are two
versions of this command: the rule can be specified as a number
in the chain (starting at 1 for the first rule) or a rule to
match.
-I, --insert chain [rulenum] rule-specification
Insert one or more rules in the selected chain as the given rule
number. So, if the rule number is 1, the rule or rules are
inserted at the head of the chain. This is also the default if
no rule number is specified.
-R, --replace chain rulenum rule-specification
Replace a rule in the selected chain. If the source and/or des‐
tination names resolve to multiple addresses, the command will
fail. Rules are numbered starting at 1.
-L, --list [chain]
List all rules in the selected chain. If no chain is selected,
all chains are listed. Like every other ip6tables command, it
applies to the specified table (filter is the default).
Please note that it is often used with the -n option, in order
to avoid long reverse DNS lookups. It is legal to specify the
-Z (zero) option as well, in which case the chain(s) will be
atomically listed and zeroed. The exact output is affected by
the other arguments given. The exact rules are suppressed until
you use
ip6tables-L -v
-S, --list-rules [chain]
Print all rules in the selected chain. If no chain is selected,
all chains are printed like ip6tables-save. Like every other
ip6tables command, it applies to the specified table (filter is
the default).
-F, --flush [chain]
Flush the selected chain (all the chains in the table if none is
given). This is equivalent to deleting all the rules one by
one.
-Z, --zero [chain]
Zero the packet and byte counters in all chains. It is legal to
specify the -L, --list (list) option as well, to see the coun‐
ters immediately before they are cleared. (See above.)
-N, --new-chain chain
Create a new user-defined chain by the given name. There must
be no target of that name already.
-X, --delete-chain [chain]
Delete the optional user-defined chain specified. There must be
no references to the chain. If there are, you must delete or
replace the referring rules before the chain can be deleted.
The chain must be empty, i.e. not contain any rules. If no
argument is given, it will attempt to delete every non-builtin
chain in the table.
-P, --policy chain target
Set the policy for the chain to the given target. See the sec‐
tion TARGETS for the legal targets. Only built-in (non-user-
defined) chains can have policies, and neither built-in nor
user-defined chains can be policy targets.
-E, --rename-chain old-chain new-chain
Rename the user specified chain to the user supplied name. This
is cosmetic, and has no effect on the structure of the table.
-A, --append chain rule-specification
Append one or more rules to the end of the selected chain. When
the source and/or destination names resolve to more than one
address, a rule will be added for each possible address combina‐
tion.
-h Help. Give a (currently very brief) description of the command
syntax.
PARAMETERS
The following parameters make up a rule specification (as used in the
add, delete, insert, replace and append commands).
[!] -p, --protocol protocol
The protocol of the rule or of the packet to check. The speci‐
fied protocol can be one of tcp, udp, udplite, icmpv6, esp, mh
or all, or it can be a numeric value, representing one of these
protocols or a different one. A protocol name from /etc/proto‐
cols is also allowed. But IPv6 extension headers except esp are
not allowed. esp and ipv6-nonext can be used with Kernel ver‐
sion 2.6.11 or later. A "!" argument before the protocol
inverts the test. The number zero is equivalent to all. Proto‐
col all will match with all protocols and is taken as default
when this option is omitted.
[!] -s, --source address[/mask]
Source specification. Address can be either a hostname (please
note that specifying any name to be resolved with a remote query
such as DNS is a really bad idea), a network IPv6 address (with
/mask), or a plain IPv6 address. (the network name isn't sup‐
ported now). The mask is a plain number, specifying the number
of 1's at the left side of the network mask. A "!" argument
before the address specification inverts the sense of the
address. The flag --src is an alias for this option.
[!] -d, --destination address[/mask]
Destination specification. See the description of the -s
(source) flag for a detailed description of the syntax. The
flag --dst is an alias for this option.
-j, --jump target
This specifies the target of the rule; i.e., what to do if the
packet matches it. The target can be a user-defined chain
(other than the one this rule is in), one of the special builtin
targets which decide the fate of the packet immediately, or an
extension (see EXTENSIONS below). If this option is omitted in
a rule (and -g is not used), then matching the rule will have no
effect on the packet's fate, but the counters on the rule will
be incremented.
-g, --goto chain
This specifies that the processing should continue in a user
specified chain. Unlike the --jump option return will not con‐
tinue processing in this chain but instead in the chain that
called us via --jump.
[!] -i, --in-interface name
Name of an interface via which a packet was received (only for
packets entering the INPUT, FORWARD and PREROUTING chains).
When the "!" argument is used before the interface name, the
sense is inverted. If the interface name ends in a "+", then
any interface which begins with this name will match. If this
option is omitted, any interface name will match.
[!] -o, --out-interface name
Name of an interface via which a packet is going to be sent (for
packets entering the FORWARD, OUTPUT and POSTROUTING chains).
When the "!" argument is used before the interface name, the
sense is inverted. If the interface name ends in a "+", then
any interface which begins with this name will match. If this
option is omitted, any interface name will match.
-c, --set-counters packets bytes
This enables the administrator to initialize the packet and byte
counters of a rule (during INSERT, APPEND, REPLACE operations).
OTHER OPTIONS
The following additional options can be specified:
-v, --verbose
Verbose output. This option makes the list command show the
interface name, the rule options (if any), and the TOS masks.
The packet and byte counters are also listed, with the suffix
'K', 'M' or 'G' for 1000, 1,000,000 and 1,000,000,000 multipli‐
ers respectively (but see the -x flag to change this). For
appending, insertion, deletion and replacement, this causes
detailed information on the rule or rules to be printed.
-n, --numeric
Numeric output. IP addresses and port numbers will be printed
in numeric format. By default, the program will try to display
them as host names, network names, or services (whenever appli‐
cable).
-x, --exact
Expand numbers. Display the exact value of the packet and byte
counters, instead of only the rounded number in K's (multiples
of 1000) M's (multiples of 1000K) or G's (multiples of 1000M).
This option is only relevant for the -L command.
--line-numbers
When listing rules, add line numbers to the beginning of each
rule, corresponding to that rule's position in the chain.
--modprobe=command
When adding or inserting rules into a chain, use command to load
any necessary modules (targets, match extensions, etc).
MATCH EXTENSIONSip6tables can use extended packet matching modules. These are loaded
in two ways: implicitly, when -p or --protocol is specified, or with
the -m or --match options, followed by the matching module name; after
these, various extra command line options become available, depending
on the specific module. You can specify multiple extended match mod‐
ules in one line, and you can use the -h or --help options after the
module has been specified to receive help specific to that module.
The following are included in the base package, and most of these can
be preceded by a "!" to invert the sense of the match.
ah
This module matches the parameters in Authentication header of IPsec
packets.
[!] --ahspi spi[:spi]
Matches SPI.
[!] --ahlen length
Total length of this header in octets.
--ahres
Matches if the reserved field is filled with zero.
cluster
Allows you to deploy gateway and back-end load-sharing clusters without
the need of load-balancers.
This match requires that all the nodes see the same packets. Thus, the
cluster match decides if this node has to handle a packet given the
following options:
--cluster-total-nodes num
Set number of total nodes in cluster.
[!] --cluster-local-node num
Set the local node number ID.
[!] --cluster-local-nodemask mask
Set the local node number ID mask. You can use this option
instead of --cluster-local-node.
--cluster-hash-seed value
Set seed value of the Jenkins hash.
Example:
iptables -A PREROUTING -t mangle -i eth1 -m cluster --clus‐
ter-total-nodes 2 --cluster-local-node 1 --cluster-hash-seed
0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth2 -m cluster --clus‐
ter-total-nodes 2 --cluster-local-node 1 --cluster-hash-seed
0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth1 -m mark ! --mark 0xffff
-j DROP
iptables -A PREROUTING -t mangle -i eth2 -m mark ! --mark 0xffff
-j DROP
And the following commands to make all nodes see the same packets:
ip maddr add 01:00:5e:00:01:01 dev eth1
ip maddr add 01:00:5e:00:01:02 dev eth2
arptables -A OUTPUT -o eth1 --h-length 6 -j mangle --mangle-mac-
s 01:00:5e:00:01:01
arptables -A INPUT -i eth1 --h-length 6 --destination-mac
01:00:5e:00:01:01 -j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
arptables -A OUTPUT -o eth2 --h-length 6 -j mangle --man‐
gle-mac-s 01:00:5e:00:01:02
arptables -A INPUT -i eth2 --h-length 6 --destination-mac
01:00:5e:00:01:02 -j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
In the case of TCP connections, pickup facility has to be disabled to
avoid marking TCP ACK packets coming in the reply direction as valid.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
comment
Allows you to add comments (up to 256 characters) to any rule.
--comment comment
Example:
iptables -A INPUT -s 192.168.0.0/16 -m comment --comment "A pri‐
vatized IP block"
connbytes
Match by how many bytes or packets a connection (or one of the two
flows constituting the connection) has transferred so far, or by aver‐
age bytes per packet.
The counters are 64-bit and are thus not expected to overflow ;)
The primary use is to detect long-lived downloads and mark them to be
scheduled using a lower priority band in traffic control.
The transferred bytes per connection can also be viewed through `con‐
ntrack -L` and accessed via ctnetlink.
NOTE that for connections which have no accounting information, the
match will always return false. The "net.netfilter.nf_conntrack_acct"
sysctl flag controls whether new connections will be byte/packet
counted. Existing connection flows will not be gaining/losing a/the
accounting structure when be sysctl flag is flipped.
[!] --connbytes from[:to]
match packets from a connection whose packets/bytes/average
packet size is more than FROM and less than TO bytes/packets. if
TO is omitted only FROM check is done. "!" is used to match
packets not falling in the range.
--connbytes-dir {original|reply|both}
which packets to consider
--connbytes-mode {packets|bytes|avgpkt}
whether to check the amount of packets, number of bytes trans‐
ferred or the average size (in bytes) of all packets received so
far. Note that when "both" is used together with "avgpkt", and
data is going (mainly) only in one direction (for example HTTP),
the average packet size will be about half of the actual data
packets.
Example:
iptables .. -m connbytes --connbytes 10000:100000
--connbytes-dir both --connbytes-mode bytes ...
connlimit
Allows you to restrict the number of parallel connections to a server
per client IP address (or client address block).
[!] --connlimit-above n
Match if the number of existing connections is (not) above n.
--connlimit-mask prefix_length
Group hosts using the prefix length. For IPv4, this must be a
number between (including) 0 and 32. For IPv6, between 0 and
128.
Examples:
# allow 2 telnet connections per client host
iptables -A INPUT -p tcp --syn--dport 23 -m connlimit
--connlimit-above 2 -j REJECT
# you can also match the other way around:
iptables -A INPUT -p tcp --syn--dport 23 -m connlimit !
--connlimit-above 2 -j ACCEPT
# limit the number of parallel HTTP requests to 16 per class C sized
network (24 bit netmask)
iptables -p tcp --syn --dport 80 -m connlimit --connlimit-above
16 --connlimit-mask 24 -j REJECT
# limit the number of parallel HTTP requests to 16 for the link local
network
(ipv6) ip6tables-p tcp --syn--dport 80 -s fe80::/64 -m
connlimit --connlimit-above 16 --connlimit-mask 64 -j REJECT
connmark
This module matches the netfilter mark field associated with a connec‐
tion (which can be set using the CONNMARK target below).
[!] --mark value[/mask]
Matches packets in connections with the given mark value (if a
mask is specified, this is logically ANDed with the mark before
the comparison).
conntrack
This module, when combined with connection tracking, allows access to
the connection tracking state for this packet/connection.
[!] --ctstate statelist
statelist is a comma separated list of the connection states to
match. Possible states are listed below.
[!] --ctproto l4proto
Layer-4 protocol to match (by number or name)
[!] --ctorigsrc address[/mask]
[!] --ctorigdst address[/mask]
[!] --ctreplsrc address[/mask]
[!] --ctrepldst address[/mask]
Match against original/reply source/destination address
[!] --ctorigsrcport port
[!] --ctorigdstport port
[!] --ctreplsrcport port
[!] --ctrepldstport port
Match against original/reply source/destination port
(TCP/UDP/etc.) or GRE key.
[!] --ctstatus statelist
statuslist is a comma separated list of the connection statuses
to match. Possible statuses are listed below.
[!] --ctexpire time[:time]
Match remaining lifetime in seconds against given value or range
of values (inclusive)
--ctdir {ORIGINAL|REPLY}
Match packets that are flowing in the specified direction. If
this flag is not specified at all, matches packets in both
directions.
States for --ctstate:
INVALID
meaning that the packet is associated with no known connection
NEW meaning that the packet has started a new connection, or other‐
wise associated with a connection which has not seen packets in
both directions, and
ESTABLISHED
meaning that the packet is associated with a connection which
has seen packets in both directions,
RELATED
meaning that the packet is starting a new connection, but is
associated with an existing connection, such as an FTP data
transfer, or an ICMP error.
SNAT A virtual state, matching if the original source address differs
from the reply destination.
DNAT A virtual state, matching if the original destination differs
from the reply source.
Statuses for --ctstatus:
NONE None of the below.
EXPECTED
This is an expected connection (i.e. a conntrack helper set it
up)
SEEN_REPLY
Conntrack has seen packets in both directions.
ASSURED
Conntrack entry should never be early-expired.
CONFIRMED
Connection is confirmed: originating packet has left box.
dccp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --dccp-types mask
Match when the DCCP packet type is one of 'mask'. 'mask' is a
comma-separated list of packet types. Packet types are: REQUEST
RESPONSE DATA ACK DATAACK CLOSEREQ CLOSE RESET SYNC SYNCACK
INVALID.
[!] --dccp-option number
Match if DCP option set.
dscp
This module matches the 6 bit DSCP field within the TOS field in the IP
header. DSCP has superseded TOS within the IETF.
[!] --dscp value
Match against a numeric (decimal or hex) value [0-63].
[!] --dscp-class class
Match the DiffServ class. This value may be any of the BE, EF,
AFxx or CSx classes. It will then be converted into its accord‐
ing numeric value.
dst
This module matches the parameters in Destination Options header
[!] --dst-len length
Total length of this header in octets.
--dst-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in
octets.
esp
This module matches the SPIs in ESP header of IPsec packets.
[!] --espspi spi[:spi]
eui64
This module matches the EUI-64 part of a stateless autoconfigured IPv6
address. It compares the EUI-64 derived from the source MAC address in
Ethernet frame with the lower 64 bits of the IPv6 source address. But
"Universal/Local" bit is not compared. This module doesn't match other
link layer frame, and is only valid in the PREROUTING, INPUT and FOR‐
WARD chains.
frag
This module matches the parameters in Fragment header.
[!] --fragid id[:id]
Matches the given Identification or range of it.
[!] --fraglen length
This option cannot be used with kernel version 2.6.10 or later.
The length of Fragment header is static and this option doesn't
make sense.
--fragres
Matches if the reserved fields are filled with zero.
--fragfirst
Matches on the first fragment.
--fragmore
Matches if there are more fragments.
--fraglast
Matches if this is the last fragment.
hashlimit
hashlimit uses hash buckets to express a rate limiting match (like the
limit match) for a group of connections using a single iptables rule.
Grouping can be done per-hostgroup (source and/or destination address)
and/or per-port. It gives you the ability to express "N packets per
time quantum per group":
matching on source host
"1000 packets per second for every host in 192.168.0.0/16"
matching on source prot
"100 packets per second for every service of 192.168.1.1"
matching on subnet
"10000 packets per minute for every /28 subnet in 10.0.0.0/8"
A hash limit option (--hashlimit-upto, --hashlimit-above) and --hash‐
limit-name are required.
--hashlimit-upto amount[/second|/minute|/hour|/day]
Match if the rate is below or equal to amount/quantum. It is
specified as a number, with an optional time quantum suffix; the
default is 3/hour.
--hashlimit-above amount[/second|/minute|/hour|/day]
Match if the rate is above amount/quantum.
--hashlimit-burst amount
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not
reached, up to this number; the default is 5.
--hashlimit-mode {srcip|srcport|dstip|dstport},...
A comma-separated list of objects to take into consideration. If
no --hashlimit-mode option is given, hashlimit acts like limit,
but at the expensive of doing the hash housekeeping.
--hashlimit-srcmask prefix
When --hashlimit-mode srcip is used, all source addresses
encountered will be grouped according to the given prefix length
and the so-created subnet will be subject to hashlimit. prefix
must be between (inclusive) 0 and 32. Note that --hashlimit-src‐
mask 0 is basically doing the same thing as not specifying srcip
for --hashlimit-mode, but is technically more expensive.
--hashlimit-dstmask prefix
Like --hashlimit-srcmask, but for destination addresses.
--hashlimit-name foo
The name for the /proc/net/ipt_hashlimit/foo entry.
--hashlimit-htable-size buckets
The number of buckets of the hash table
--hashlimit-htable-max entries
Maximum entries in the hash.
--hashlimit-htable-expire msec
After how many milliseconds do hash entries expire.
--hashlimit-htable-gcinterval msec
How many milliseconds between garbage collection intervals.
hbh
This module matches the parameters in Hop-by-Hop Options header
[!] --hbh-len length
Total length of this header in octets.
--hbh-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in
octets.
helper
This module matches packets related to a specific conntrack-helper.
[!] --helper string
Matches packets related to the specified conntrack-helper.
string can be "ftp" for packets related to a ftp-session on
default port. For other ports append -portnr to the value, ie.
"ftp-2121".
Same rules apply for other conntrack-helpers.
hl
This module matches the Hop Limit field in the IPv6 header.
[!] --hl-eq value
Matches if Hop Limit equals value.
--hl-lt value
Matches if Hop Limit is less than value.
--hl-gt value
Matches if Hop Limit is greater than value.
icmp6
This extension can be used if `--protocol ipv6-icmp' or `--protocol
icmpv6' is specified. It provides the following option:
[!] --icmpv6-type type[/code]|typename
This allows specification of the ICMPv6 type, which can be a
numeric ICMPv6 type, type and code, or one of the ICMPv6 type
names shown by the command
ip6tables-p ipv6-icmp -h
iprange
This matches on a given arbitrary range of IP addresses.
[!] --src-range from[-to]
Match source IP in the specified range.
[!] --dst-range from[-to]
Match destination IP in the specified range.
ipv6header
This module matches IPv6 extension headers and/or upper layer header.
--soft Matches if the packet includes any of the headers specified with
--header.
[!] --header header[,header...]
Matches the packet which EXACTLY includes all specified headers.
The headers encapsulated with ESP header are out of scope. Pos‐
sible header types can be:
hop|hop-by-hop
Hop-by-Hop Options header
dst Destination Options header
route Routing header
frag Fragment header
auth Authentication header
esp Encapsulating Security Payload header
none No Next header which matches 59 in the 'Next Header field' of
IPv6 header or any IPv6 extension headers
proto which matches any upper layer protocol header. A protocol name
from /etc/protocols and numeric value also allowed. The number
255 is equivalent to proto.
length
This module matches the length of the layer-3 payload (e.g. layer-4
packet) f a packet against a specific value or range of values.
[!] --length length[:length]
limit
This module matches at a limited rate using a token bucket filter. A
rule using this extension will match until this limit is reached
(unless the `!' flag is used). It can be used in combination with the
LOG target to give limited logging, for example.
[!] --limit rate[/second|/minute|/hour|/day]
Maximum average matching rate: specified as a number, with an
optional `/second', `/minute', `/hour', or `/day' suffix; the
default is 3/hour.
--limit-burst number
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not
reached, up to this number; the default is 5.
mac
[!] --mac-source address
Match source MAC address. It must be of the form
XX:XX:XX:XX:XX:XX. Note that this only makes sense for packets
coming from an Ethernet device and entering the PREROUTING, FOR‐
WARD or INPUT chains.
mark
This module matches the netfilter mark field associated with a packet
(which can be set using the MARK target below).
[!] --mark value[/mask]
Matches packets with the given unsigned mark value (if a mask is
specified, this is logically ANDed with the mask before the com‐
parison).
mh
This extension is loaded if `--protocol ipv6-mh' or `--protocol mh' is
specified. It provides the following option:
[!] --mh-type type[:type]
This allows specification of the Mobility Header(MH) type, which
can be a numeric MH type, type or one of the MH type names shown
by the command
ip6tables-p ipv6-mh -h
multiport
This module matches a set of source or destination ports. Up to 15
ports can be specified. A port range (port:port) counts as two ports.
It can only be used in conjunction with -p tcp or -p udp.
[!] --source-ports,--sports port[,port|,port:port]...
Match if the source port is one of the given ports. The flag
--sports is a convenient alias for this option. Multiple ports
or port ranges are separated using a comma, and a port range is
specified using a colon. 53,1024:65535 would therefore match
ports 53 and all from 1024 through 65535.
[!] --destination-ports,--dports port[,port|,port:port]...
Match if the destination port is one of the given ports. The
flag --dports is a convenient alias for this option.
[!] --ports port[,port|,port:port]...
Match if either the source or destination ports are equal to one
of the given ports.
owner
This module attempts to match various characteristics of the packet
creator, for locally generated packets. This match is only valid in the
OUTPUT and POSTROUTING chains. Forwarded packets do not have any socket
associated with them. Packets from kernel threads do have a socket, but
usually no owner.
[!] --uid-owner username
[!] --uid-owner userid[-userid]
Matches if the packet socket's file structure (if it has one) is
owned by the given user. You may also specify a numerical UID,
or an UID range.
[!] --gid-owner groupname
[!] --gid-owner groupid[-groupid]
Matches if the packet socket's file structure is owned by the
given group. You may also specify a numerical GID, or a GID
range.
[!] --socket-exists
Matches if the packet is associated with a socket.
physdev
This module matches on the bridge port input and output devices
enslaved to a bridge device. This module is a part of the infrastruc‐
ture that enables a transparent bridging IP firewall and is only useful
for kernel versions above version 2.5.44.
[!] --physdev-in name
Name of a bridge port via which a packet is received (only for
packets entering the INPUT, FORWARD and PREROUTING chains). If
the interface name ends in a "+", then any interface which
begins with this name will match. If the packet didn't arrive
through a bridge device, this packet won't match this option,
unless '!' is used.
[!] --physdev-out name
Name of a bridge port via which a packet is going to be sent
(for packets entering the FORWARD, OUTPUT and POSTROUTING
chains). If the interface name ends in a "+", then any inter‐
face which begins with this name will match. Note that in the
nat and mangle OUTPUT chains one cannot match on the bridge out‐
put port, however one can in the filter OUTPUT chain. If the
packet won't leave by a bridge device or if it is yet unknown
what the output device will be, then the packet won't match this
option, unless '!' is used.
[!] --physdev-is-in
Matches if the packet has entered through a bridge interface.
[!] --physdev-is-out
Matches if the packet will leave through a bridge interface.
[!] --physdev-is-bridged
Matches if the packet is being bridged and therefore is not
being routed. This is only useful in the FORWARD and POSTROUT‐
ING chains.
pkttype
This module matches the link-layer packet type.
[!] --pkt-type {unicast|broadcast|multicast}
policy
This modules matches the policy used by IPsec for handling a packet.
--dir {in|out}
Used to select whether to match the policy used for decapsula‐
tion or the policy that will be used for encapsulation. in is
valid in the PREROUTING, INPUT and FORWARD chains, out is valid
in the POSTROUTING, OUTPUT and FORWARD chains.
--pol {none|ipsec}
Matches if the packet is subject to IPsec processing.
--strict
Selects whether to match the exact policy or match if any rule
of the policy matches the given policy.
[!] --reqid id
Matches the reqid of the policy rule. The reqid can be specified
with setkey(8) using unique:id as level.
[!] --spi spi
Matches the SPI of the SA.
[!] --proto {ah|esp|ipcomp}
Matches the encapsulation protocol.
[!] --mode {tunnel|transport}
Matches the encapsulation mode.
[!] --tunnel-src addr[/mask]
Matches the source end-point address of a tunnel mode SA. Only
valid with --mode tunnel.
[!] --tunnel-dst addr[/mask]
Matches the destination end-point address of a tunnel mode SA.
Only valid with --mode tunnel.
--next Start the next element in the policy specification. Can only be
used with --strict.
quota
Implements network quotas by decrementing a byte counter with each
packet.
--quota bytes
The quota in bytes.
rateest
The rate estimator can match on estimated rates as collected by the
RATEEST target. It supports matching on absolute bps/pps values, com‐
paring two rate estimators and matching on the difference between two
rate estimators.
--rateest1 name
Name of the first rate estimator.
--rateest2 name
Name of the second rate estimator (if difference is to be calcu‐
lated).
--rateest-delta
Compare difference(s) to given rate(s)--rateest1-bps value
--rateest2-bps value
Compare bytes per second.
--rateest1-pps value
--rateest2-pps value
Compare packets per second.
[!] --rateest-lt
Match if rate is less than given rate/estimator.
[!] --rateest-gt
Match if rate is greater than given rate/estimator.
[!] --rateest-eq
Match if rate is equal to given rate/estimator.
Example: This is what can be used to route outgoing data connections
from an FTP server over two lines based on the available bandwidth at
the time the data connection was started:
# Estimate outgoing rates
iptables -t mangle -A POSTROUTING -o eth0 -j RATEEST --rateest-name
eth0 --rateest-interval 250ms --rateest-ewma 0.5s
iptables -t mangle -A POSTROUTING -o ppp0 -j RATEEST --rateest-name
ppp0 --rateest-interval 250ms --rateest-ewma 0.5s
# Mark based on available bandwidth
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper
--helper ftp -m rateest --rateest-delta --rateest1 eth0 --rateest-bps1
2.5mbit --rateest-gt --rateest2 ppp0 --rateest-bps2 2mbit -j CONNMARK
--set-mark 1
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper
--helper ftp -m rateest --rateest-delta --rateest1 ppp0 --rateest-bps1
2mbit --rateest-gt--rateest2 eth0 --rateest-bps2 2.5mbit -j CONNMARK
--set-mark 2
iptables -t mangle -A balance -j CONNMARK --restore-mark
recent
Allows you to dynamically create a list of IP addresses and then match
against that list in a few different ways.
For example, you can create a "badguy" list out of people attempting to
connect to port 139 on your firewall and then DROP all future packets
from them without considering them.
--name name
Specify the list to use for the commands. If no name is given
then DEFAULT will be used.
[!] --set
This will add the source address of the packet to the list. If
the source address is already in the list, this will update the
existing entry. This will always return success (or failure if !
is passed in).
--rsource
Match/save the source address of each packet in the recent list
table. This is the default.
--rdest
Match/save the destination address of each packet in the recent
list table.
[!] --rcheck
Check if the source address of the packet is currently in the
list.
[!] --update
Like --rcheck, except it will update the "last seen" timestamp
if it matches.
[!] --remove
Check if the source address of the packet is currently in the
list and if so that address will be removed from the list and
the rule will return true. If the address is not found, false is
returned.
[!] --seconds seconds
This option must be used in conjunction with one of --rcheck or
--update. When used, this will narrow the match to only happen
when the address is in the list and was seen within the last
given number of seconds.
--reap reap
This option must be used in conjunction with --seconds. When
used, this will remove entries with the most recent timestamp
older then --seconds since the last packet was received.
[!] --hitcount hits
This option must be used in conjunction with one of --rcheck or
--update. When used, this will narrow the match to only happen
when the address is in the list and packets had been received
greater than or equal to the given value. This option may be
used along with --seconds to create an even narrower match
requiring a certain number of hits within a specific time frame.
--rttl This option may only be used in conjunction with one of --rcheck
or --update. When used, this will narrow the match to only hap‐
pen when the address is in the list and the TTL of the current
packet matches that of the packet which hit the --set rule. This
may be useful if you have problems with people faking their
source address in order to DoS you via this module by disallow‐
ing others access to your site by sending bogus packets to you.
Examples:
iptables -A FORWARD -m recent --name badguy --rcheck--seconds
60 -j DROP
iptables -A FORWARD -p tcp -i eth0 --dport 139 -m recent --name
badguy --set -j DROP
Steve's ipt_recent website (http://snowman.net/projects/ipt_recent/)
also has some examples of usage.
/proc/net/xt_recent/* are the current lists of addresses and informa‐
tion about each entry of each list.
Each file in /proc/net/xt_recent/ can be read from to see the current
list or written two using the following commands to modify the list:
echo +addr >/proc/net/xt_recent/DEFAULT
to add addr to the DEFAULT list
echo -addr >/proc/net/xt_recent/DEFAULT
to remove addr from the DEFAULT list
echo / >/proc/net/xt_recent/DEFAULT
to flush the DEFAULT list (remove all entries).
The module itself accepts parameters, defaults shown:
ip_list_tot=100
Number of addresses remembered per table.
ip_pkt_list_tot=20
Number of packets per address remembered.
ip_list_hash_size=0
Hash table size. 0 means to calculate it based on ip_list_tot,
default: 512.
ip_list_perms=0644
Permissions for /proc/net/xt_recent/* files.
ip_list_uid=0
Numerical UID for ownership of /proc/net/xt_recent/* files.
ip_list_gid=0
Numerical GID for ownership of /proc/net/xt_recent/* files.
rt
Match on IPv6 routing header
[!] --rt-type type
Match the type (numeric).
[!] --rt-segsleft num[:num]
Match the `segments left' field (range).
[!] --rt-len length
Match the length of this header.
--rt-0-res
Match the reserved field, too (type=0)
--rt-0-addrs addr[,addr...]
Match type=0 addresses (list).
--rt-0-not-strict
List of type=0 addresses is not a strict list.
sctp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --chunk-types {all|any|only} chunktype[:flags] [...]
The flag letter in upper case indicates that the flag is to
match if set, in the lower case indicates to match if unset.
Chunk types: DATA INIT INIT_ACK SACK HEARTBEAT HEARTBEAT_ACK
ABORT SHUTDOWN SHUTDOWN_ACK ERROR COOKIE_ECHO COOKIE_ACK
ECN_ECNE ECN_CWR SHUTDOWN_COMPLETE ASCONF ASCONF_ACK
chunk type available flags
DATA U B E u b e
ABORT T t
SHUTDOWN_COMPLETE T t
(lowercase means flag should be "off", uppercase means "on")
Examples:
iptables -A INPUT -p sctp --dport 80 -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA,INIT -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA:Be -j ACCEPT
state
This module, when combined with connection tracking, allows access to
the connection tracking state for this packet.
[!] --state state
Where state is a comma separated list of the connection states
to match. Possible states are INVALID meaning that the packet
could not be identified for some reason which includes running
out of memory and ICMP errors which don't correspond to any
known connection, ESTABLISHED meaning that the packet is associ‐
ated with a connection which has seen packets in both direc‐
tions, NEW meaning that the packet has started a new connection,
or otherwise associated with a connection which has not seen
packets in both directions, and RELATED meaning that the packet
is starting a new connection, but is associated with an existing
connection, such as an FTP data transfer, or an ICMP error.
statistic
This module matches packets based on some statistic condition. It sup‐
ports two distinct modes settable with the --mode option.
Supported options:
--mode mode
Set the matching mode of the matching rule, supported modes are
random and nth.
--probability p
Set the probability from 0 to 1 for a packet to be randomly
matched. It works only with the random mode.
--every n
Match one packet every nth packet. It works only with the nth
mode (see also the --packet option).
--packet p
Set the initial counter value (0 <= p <= n-1, default 0) for the
nth mode.
string
This modules matches a given string by using some pattern matching
strategy. It requires a linux kernel >= 2.6.14.
--algo {bm|kmp}
Select the pattern matching strategy. (bm = Boyer-Moore, kmp =
Knuth-Pratt-Morris)
--from offset
Set the offset from which it starts looking for any matching. If
not passed, default is 0.
--to offset
Set the offset from which it starts looking for any matching. If
not passed, default is the packet size.
[!] --string pattern
Matches the given pattern.
[!] --hex-string pattern
Matches the given pattern in hex notation.
tcp
These extensions can be used if `--protocol tcp' is specified. It pro‐
vides the following options:
[!] --source-port,--sport port[:port]
Source port or port range specification. This can either be a
service name or a port number. An inclusive range can also be
specified, using the format first:last. If the first port is
omitted, "0" is assumed; if the last is omitted, "65535" is
assumed. If the first port is greater than the second one they
will be swapped. The flag --sport is a convenient alias for
this option.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. The flag --dport
is a convenient alias for this option.
[!] --tcp-flags mask comp
Match when the TCP flags are as specified. The first argument
mask is the flags which we should examine, written as a comma-
separated list, and the second argument comp is a comma-sepa‐
rated list of flags which must be set. Flags are: SYN ACK FIN
RST URG PSH ALL NONE. Hence the command
iptables -A FORWARD -p tcp --tcp-flags SYN,ACK,FIN,RST SYN
will only match packets with the SYN flag set, and the ACK, FIN
and RST flags unset.
[!] --syn
Only match TCP packets with the SYN bit set and the ACK,RST and
FIN bits cleared. Such packets are used to request TCP connec‐
tion initiation; for example, blocking such packets coming in an
interface will prevent incoming TCP connections, but outgoing
TCP connections will be unaffected. It is equivalent to
--tcp-flags SYN,RST,ACK,FIN SYN. If the "!" flag precedes the
"--syn", the sense of the option is inverted.
[!] --tcp-option number
Match if TCP option set.
tcpmss
This matches the TCP MSS (maximum segment size) field of the TCP
header. You can only use this on TCP SYN or SYN/ACK packets, since the
MSS is only negotiated during the TCP handshake at connection startup
time.
[!] --mss value[:value]
Match a given TCP MSS value or range.
time
This matches if the packet arrival time/date is within a given range.
All options are optional, but are ANDed when specified.
--datestart YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
--datestop YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
Only match during the given time, which must be in ISO 8601 "T"
notation. The possible time range is 1970-01-01T00:00:00 to
2038-01-19T04:17:07.
If --datestart or --datestop are not specified, it will default
to 1970-01-01 and 2038-01-19, respectively.
--timestart hh:mm[:ss]
--timestop hh:mm[:ss]
Only match during the given daytime. The possible time range is
00:00:00 to 23:59:59. Leading zeroes are allowed (e.g. "06:03")
and correctly interpreted as base-10.
[!] --monthdays day[,day...]
Only match on the given days of the month. Possible values are 1
to 31. Note that specifying 31 will of course not match on
months which do not have a 31st day; the same goes for 28- or
29-day February.
[!] --weekdays day[,day...]
Only match on the given weekdays. Possible values are Mon, Tue,
Wed, Thu, Fri, Sat, Sun, or values from 1 to 7, respectively.
You may also use two-character variants (Mo, Tu, etc.).
--utc
Interpret the times given for --datestart, --datestop, --times‐
tart and --timestop to be UTC.
--localtz
Interpret the times given for --datestart, --datestop, --times‐
tart and --timestop to be local kernel time. (Default)
EXAMPLES. To match on weekends, use:
-m time --weekdays Sa,Su
Or, to match (once) on a national holiday block:
-m time --datestart 2007-12-24 --datestop 2007-12-27
Since the stop time is actually inclusive, you would need the following
stop time to not match the first second of the new day:
-m time --datestart 2007-01-01T17:00 --datestop
2007-01-01T23:59:59
During lunch hour:
-m time --timestart 12:30 --timestop 13:30
The fourth Friday in the month:
-m time --weekdays Fr --monthdays 22,23,24,25,26,27,28
(Note that this exploits a certain mathematical property. It is not
possible to say "fourth Thursday OR fourth Friday" in one rule. It is
possible with multiple rules, though.)
tos
This module matches the 8-bit Type of Service field in the IPv4 header
(i.e. including the "Precedence" bits) or the (also 8-bit) Priority
field in the IPv6 header.
[!] --tos value[/mask]
Matches packets with the given TOS mark value. If a mask is
specified, it is logically ANDed with the TOS mark before the
comparison.
[!] --tos symbol
You can specify a symbolic name when using the tos match for
IPv4. The list of recognized TOS names can be obtained by call‐
ing iptables with -m tos -h. Note that this implies a mask of
0x3F, i.e. all but the ECN bits.
u32
U32 tests whether quantities of up to 4 bytes extracted from a packet
have specified values. The specification of what to extract is general
enough to find data at given offsets from tcp headers or payloads.
[!] --u32 tests
The argument amounts to a program in a small language described
below.
tests := location "=" value | tests "&&" location "=" value
value := range | value "," range
range := number | number ":" number
a single number, n, is interpreted the same as n:n. n:m is interpreted
as the range of numbers >=n and <=m.
location := number | location operator number
operator := "&" | "<<" | ">>" | "@"
The operators &, <<, >> and && mean the same as in C. The = is really
a set membership operator and the value syntax describes a set. The @
operator is what allows moving to the next header and is described fur‐
ther below.
There are currently some artificial implementation limits on the size
of the tests:
* no more than 10 of "=" (and 9 "&&"s) in the u32 argument
* no more than 10 ranges (and 9 commas) per value
* no more than 10 numbers (and 9 operators) per location
To describe the meaning of location, imagine the following machine that
interprets it. There are three registers:
A is of type char *, initially the address of the IP header
B and C are unsigned 32 bit integers, initially zero
The instructions are:
number B = number;
C = (*(A+B)<<24) + (*(A+B+1)<<16) + (*(A+B+2)<<8) + *(A+B+3)
&number C = C & number
<< number C = C << number
>> number C = C >> number
@number A = A + C; then do the instruction number
Any access of memory outside [skb->data,skb->end] causes the match to
fail. Otherwise the result of the computation is the final value of C.
Whitespace is allowed but not required in the tests. However, the char‐
acters that do occur there are likely to require shell quoting, so it
is a good idea to enclose the arguments in quotes.
Example:
match IP packets with total length >= 256
The IP header contains a total length field in bytes 2-3.
--u32 "0 & 0xFFFF = 0x100:0xFFFF"
read bytes 0-3
AND that with 0xFFFF (giving bytes 2-3), and test whether that
is in the range [0x100:0xFFFF]
Example: (more realistic, hence more complicated)
match ICMP packets with icmp type 0
First test that it is an ICMP packet, true iff byte 9 (protocol)
= 1
--u32 "6 & 0xFF = 1 && ...
read bytes 6-9, use & to throw away bytes 6-8 and compare the
result to 1. Next test that it is not a fragment. (If so, it
might be part of such a packet but we cannot always tell.) N.B.:
This test is generally needed if you want to match anything
beyond the IP header. The last 6 bits of byte 6 and all of byte
7 are 0 iff this is a complete packet (not a fragment). Alterna‐
tively, you can allow first fragments by only testing the last 5
bits of byte 6.
... 4 & 0x3FFF = 0 && ...
Last test: the first byte past the IP header (the type) is 0.
This is where we have to use the @syntax. The length of the IP
header (IHL) in 32 bit words is stored in the right half of byte
0 of the IP header itself.
... 0 >> 22 & 0x3C @ 0 >> 24 = 0"
The first 0 means read bytes 0-3, >>22 means shift that 22 bits
to the right. Shifting 24 bits would give the first byte, so
only 22 bits is four times that plus a few more bits. &3C then
eliminates the two extra bits on the right and the first four
bits of the first byte. For instance, if IHL=5, then the IP
header is 20 (4 x 5) bytes long. In this case, bytes 0-1 are (in
binary) xxxx0101 yyzzzzzz, >>22 gives the 10 bit value
xxxx0101yy and &3C gives 010100. @ means to use this number as a
new offset into the packet, and read four bytes starting from
there. This is the first 4 bytes of the ICMP payload, of which
byte 0 is the ICMP type. Therefore, we simply shift the value 24
to the right to throw out all but the first byte and compare the
result with 0.
Example:
TCP payload bytes 8-12 is any of 1, 2, 5 or 8
First we test that the packet is a tcp packet (similar to ICMP).
--u32 "6 & 0xFF = 6 && ...
Next, test that it is not a fragment (same as above).
... 0 >> 22 & 0x3C @ 12 >> 26 & 0x3C @ 8 = 1,2,5,8"
0>>22&3C as above computes the number of bytes in the IP header.
@ makes this the new offset into the packet, which is the start
of the TCP header. The length of the TCP header (again in 32 bit
words) is the left half of byte 12 of the TCP header. The
12>>26&3C computes this length in bytes (similar to the IP
header before). "@" makes this the new offset, which is the
start of the TCP payload. Finally, 8 reads bytes 8-12 of the
payload and = checks whether the result is any of 1, 2, 5 or 8.
udp
These extensions can be used if `--protocol udp' is specified. It pro‐
vides the following options:
[!] --source-port,--sport port[:port]
Source port or port range specification. See the description of
the --source-port option of the TCP extension for details.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. See the descrip‐
tion of the --destination-port option of the TCP extension for
details.
TARGET EXTENSIONSip6tables can use extended target modules: the following are included
in the standard distribution.
CLASSIFY
This module allows you to set the skb->priority value (and thus clas‐
sify the packet into a specific CBQ class).
--set-class major:minor
Set the major and minor class value. The values are always
interpreted as hexadecimal even if no 0x prefix is given.
CONNMARK
This module sets the netfilter mark value associated with a connection.
--set-xmark value[/mask]
Zero out the bits given by mask and XOR value into the ctmark.
--save-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the packet mark (nfmark) to the connection mark (ctmark)
using the given masks. The new nfmark value is determined as
follows:
ctmark = (ctmark & ~ctmask) ^ (nfmark & nfmask)
i.e. ctmask defines what bits to clear and nfmask what bits of
the nfmark to XOR into the ctmark. ctmask and nfmask default to
0xFFFFFFFF.
--restore-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the connection mark (ctmark) to the packet mark (nfmark)
using the given masks. The new ctmark value is determined as
follows:
nfmark = (nfmark & ~nfmask) ^ (ctmark & ctmask);
i.e. nfmask defines what bits to clear and ctmask what bits of
the ctmark to XOR into the nfmark. ctmask and nfmask default to
0xFFFFFFFF.
--restore-mark is only valid in the mangle table.
The following mnemonics are available for --set-xmark:
--and-mark bits
Binary AND the ctmark with bits. (Mnemonic for --set-xmark
0/invbits, where invbits is the binary negation of bits.)
--or-mark bits
Binary OR the ctmark with bits. (Mnemonic for --set-xmark
bits/bits.)
--xor-mark bits
Binary XOR the ctmark with bits. (Mnemonic for --set-xmark
bits/0.)
--set-mark value[/mask]
Set the connection mark. If a mask is specified then only those
bits set in the mask are modified.
--save-mark [--mask mask]
Copy the nfmark to the ctmark. If a mask is specified, only
those bits are copied.
--restore-mark [--mask mask]
Copy the ctmark to the nfmark. If a mask is specified, only
those bits are copied. This is only valid in the mangle table.
CONNSECMARK
This module copies security markings from packets to connections (if
unlabeled), and from connections back to packets (also only if unla‐
beled). Typically used in conjunction with SECMARK, it is only valid
in the mangle table.
--save If the packet has a security marking, copy it to the connection
if the connection is not marked.
--restore
If the packet does not have a security marking, and the connec‐
tion does, copy the security marking from the connection to the
packet.
DSCP
This target allows to alter the value of the DSCP bits within the TOS
header of the IPv4 packet. As this manipulates a packet, it can only
be used in the mangle table.
--set-dscp value
Set the DSCP field to a numerical value (can be decimal or hex)
--set-dscp-class class
Set the DSCP field to a DiffServ class.
HL
This is used to modify the Hop Limit field in IPv6 header. The Hop
Limit field is similar to what is known as TTL value in IPv4. Setting
or incrementing the Hop Limit field can potentially be very dangerous,
so it should be avoided at any cost. This target is only valid in man‐
gle table.
Don't ever set or increment the value on packets that leave your local
network!
--hl-set value
Set the Hop Limit to `value'.
--hl-dec value
Decrement the Hop Limit `value' times.
--hl-inc value
Increment the Hop Limit `value' times.
LOG
Turn on kernel logging of matching packets. When this option is set
for a rule, the Linux kernel will print some information on all match‐
ing packets (like most IPv6 IPv6-header fields) via the kernel log
(where it can be read with dmesg or syslogd(8)). This is a "non-termi‐
nating target", i.e. rule traversal continues at the next rule. So if
you want to LOG the packets you refuse, use two separate rules with the
same matching criteria, first using target LOG then DROP (or REJECT).
--log-level level
Level of logging (numeric or see syslog.conf(5)).
--log-prefix prefix
Prefix log messages with the specified prefix; up to 29 letters
long, and useful for distinguishing messages in the logs.
--log-tcp-sequence
Log TCP sequence numbers. This is a security risk if the log is
readable by users.
--log-tcp-options
Log options from the TCP packet header.
--log-ip-options
Log options from the IPv6 packet header.
--log-uid
Log the userid of the process which generated the packet.
MARK
This target is used to set the Netfilter mark value associated with the
packet. The target can only be used in the mangle table. It can, for
example, be used in conjunction with routing based on fwmark (needs
iproute2).
--set-xmark value[/mask]
Zeroes out the bits given by mask and XORs value into the packet
mark ("nfmark"). If mask is omitted, 0xFFFFFFFF is assumed.
--set-mark value[/mask]
Zeroes out the bits given by mask and ORs value into the packet
mark. If mask is omitted, 0xFFFFFFFF is assumed.
The following mnemonics are available:
--and-mark bits
Binary AND the nfmark with bits. (Mnemonic for --set-xmark
0/invbits, where invbits is the binary negation of bits.)
--or-mark bits
Binary OR the nfmark with bits. (Mnemonic for --set-xmark
bits/bits.)
--xor-mark bits
Binary XOR the nfmark with bits. (Mnemonic for --set-xmark
bits/0.)
NFLOG
This target provides logging of matching packets. When this target is
set for a rule, the Linux kernel will pass the packet to the loaded
logging backend to log the packet. This is usually used in combination
with nfnetlink_log as logging backend, which will multicast the packet
through a netlink socket to the specified multicast group. One or more
userspace processes may subscribe to the group to receive the packets.
Like LOG, this is a non-terminating target, i.e. rule traversal contin‐
ues at the next rule.
--nflog-group nlgroup
The netlink group (1 - 2^32-1) to which packets are (only appli‐
cable for nfnetlink_log). The default value is 0.
--nflog-prefix prefix
A prefix string to include in the log message, up to 64 charac‐
ters long, useful for distinguishing messages in the logs.
--nflog-range size
The number of bytes to be copied to userspace (only applicable
for nfnetlink_log). nfnetlink_log instances may specify their
own range, this option overrides it.
--nflog-threshold size
Number of packets to queue inside the kernel before sending them
to userspace (only applicable for nfnetlink_log). Higher values
result in less overhead per packet, but increase delay until the
packets reach userspace. The default value is 1.
NFQUEUE
This target is an extension of the QUEUE target. As opposed to QUEUE,
it allows you to put a packet into any specific queue, identified by
its 16-bit queue number.
--queue-num value
This specifies the QUEUE number to use. Valid queue numbers are
0 to 65535. The default value is 0.
It can only be used with Kernel versions 2.6.14 or later, since it
requires the nfnetlink_queue kernel support.
NOTRACK
This target disables connection tracking for all packets matching that
rule.
It can only be used in the raw table.
RATEEST
The RATEEST target collects statistics, performs rate estimation calcu‐
lation and saves the results for later evaluation using the rateest
match.
--rateest-name name
Count matched packets into the pool referred to by name, which
is freely choosable.
--rateest-interval amount{s|ms|us}
Rate measurement interval, in seconds, milliseconds or microsec‐
onds.
--rateest-ewmalog value
Rate measurement averaging time constant.
REJECT
This is used to send back an error packet in response to the matched
packet: otherwise it is equivalent to DROP so it is a terminating TAR‐
GET, ending rule traversal. This target is only valid in the INPUT,
FORWARD and OUTPUT chains, and user-defined chains which are only
called from those chains. The following option controls the nature of
the error packet returned:
--reject-with type
The type given can be icmp6-no-route, no-route, icmp6-adm-pro‐
hibited, adm-prohibited, icmp6-addr-unreachable, addr-unreach,
icmp6-port-unreachable or port-unreach which return the appro‐
priate ICMPv6 error message (port-unreach is the default).
Finally, the option tcp-reset can be used on rules which only
match the TCP protocol: this causes a TCP RST packet to be sent
back. This is mainly useful for blocking ident (113/tcp) probes
which frequently occur when sending mail to broken mail hosts
(which won't accept your mail otherwise). tcp-reset can only be
used with kernel versions 2.6.14 or later.
SECMARK
This is used to set the security mark value associated with the packet
for use by security subsystems such as SELinux. It is only valid in
the mangle table.
--selctx security_context
TCPMSS
This target allows to alter the MSS value of TCP SYN packets, to con‐
trol the maximum size for that connection (usually limiting it to your
outgoing interface's MTU minus 40 for IPv4 or 60 for IPv6, respec‐
tively). Of course, it can only be used in conjunction with -p tcp.
It is only valid in the mangle table.
This target is used to overcome criminally braindead ISPs or servers
which block "ICMP Fragmentation Needed" or "ICMPv6 Packet Too Big"
packets. The symptoms of this problem are that everything works fine
from your Linux firewall/router, but machines behind it can never
exchange large packets:
1) Web browsers connect, then hang with no data received.
2) Small mail works fine, but large emails hang.
3) ssh works fine, but scp hangs after initial handshaking.
Workaround: activate this option and add a rule to your firewall con‐
figuration like:
iptables -t mangle -A FORWARD -p tcp --tcp-flags SYN,RST SYN
-j TCPMSS --clamp-mss-to-pmtu
--set-mss value
Explicitly set MSS option to specified value.
--clamp-mss-to-pmtu
Automatically clamp MSS value to (path_MTU - 40 for IPv4; -60
for IPv6).
These options are mutually exclusive.
TCPOPTSTRIP
This target will strip TCP options off a TCP packet. (It will actually
replace them by NO-OPs.) As such, you will need to add the -p tcp
parameters.
--strip-options option[,option...]
Strip the given option(s). The options may be specified by TCP
option number or by symbolic name. The list of recognized
options can be obtained by calling iptables with -j TCPOPTSTRIP
-h.
TOS
This module sets the Type of Service field in the IPv4 header (includ‐
ing the ´precedence´ bits) or the Priority field in the IPv6 header.
Note that TOS shares the same bits as DSCP and ECN. The TOS target is
only valid in the mangle table.
--set-tos value[/mask]
Zeroes out the bits given by mask and XORs value into the
TOS/Priority field. If mask is omitted, 0xFF is assumed.
--set-tos symbol
You can specify a symbolic name when using the TOS target for
IPv4. It implies a mask of 0xFF. The list of recognized TOS
names can be obtained by calling iptables with -j TOS -h.
The following mnemonics are available:
--and-tos bits
Binary AND the TOS value with bits. (Mnemonic for --set-tos
0/invbits, where invbits is the binary negation of bits.)
--or-tos bits
Binary OR the TOS value with bits. (Mnemonic for --set-tos
bits/bits.)
--xor-tos bits
Binary XOR the TOS value with bits. (Mnemonic for --set-tos
bits/0.)
TRACE
This target marks packes so that the kernel will log every rule which
match the packets as those traverse the tables, chains, rules. (The
ipt_LOG or ip6t_LOG module is required for the logging.) The packets
are logged with the string prefix: "TRACE: tablename:chain‐
name:type:rulenum " where type can be "rule" for plain rule, "return"
for implicit rule at the end of a user defined chain and "policy" for
the policy of the built in chains.
It can only be used in the raw table.
DIAGNOSTICS
Various error messages are printed to standard error. The exit code is
0 for correct functioning. Errors which appear to be caused by invalid
or abused command line parameters cause an exit code of 2, and other
errors cause an exit code of 1.
BUGS
Bugs? What's this? ;-) Well... the counters are not reliable on
sparc64.
COMPATIBILITY WITH IPCHAINS
This ip6tables is very similar to ipchains by Rusty Russell. The main
difference is that the chains INPUT and OUTPUT are only traversed for
packets coming into the local host and originating from the local host
respectively. Hence every packet only passes through one of the three
chains (except loopback traffic, which involves both INPUT and OUTPUT
chains); previously a forwarded packet would pass through all three.
The other main difference is that -i refers to the input interface; -o
refers to the output interface, and both are available for packets
entering the FORWARD chain. There are several other changes in
ip6tables.
SEE ALSOip6tables-save(8), ip6tables-restore(8), iptables(8), iptables-save(8),
iptables-restore(8), libipq(3).
The packet-filtering-HOWTO details iptables usage for packet filtering,
the netfilter-extensions-HOWTO details the extensions that are not in
the standard distribution, and the netfilter-hacking-HOWTO details the
netfilter internals.
See http://www.netfilter.org/.
AUTHORS
Rusty Russell wrote iptables, in early consultation with Michael Neul‐
ing.
Marc Boucher made Rusty abandon ipnatctl by lobbying for a generic
packet selection framework in iptables, then wrote the mangle table,
the owner match, the mark stuff, and ran around doing cool stuff every‐
where.
James Morris wrote the TOS target, and tos match.
Jozsef Kadlecsik wrote the REJECT target.
Harald Welte wrote the ULOG and NFQUEUE target, the new libiptc, as
well as TTL match+target and libipulog.
The Netfilter Core Team is: Marc Boucher, Martin Josefsson, Yasuyuki
Kozakai, Jozsef Kadlecsik, Patrick McHardy, James Morris, Pablo Neira
Ayuso, Harald Welte and Rusty Russell.
ip6tables man page created by Andras Kis-Szabo, based on iptables man
page written by Herve Eychenne <rv@wallfire.org>.
iptables 1.4.4IP6TABLES(8)
