init man page on Scientific

Man page or keyword search:  
man Server   26626 pages
apropos Keyword Search (all sections)
Output format
Scientific logo
[printable version]

init(5)								       init(5)

NAME
       init - Upstart init daemon job configuration

SYNOPSIS
       /etc/init/

DESCRIPTION
       On startup, the Upstart init(8) daemon reads its job configuration from
       the /etc/init directory, and watches  for  future  changes  using  ino‐
       tify(7).

       To be considered by Upstart, files in this directory must have a recog‐
       nized suffix and may also be present in sub-directories.	 There are two
       recognized suffixes:

       ·   Files  ending  in  .conf  are called configuration files, or simply
	   "conf files" for short.  These are the primary vehicle for specify‐
	   ing a job.

       ·   Files  ending  in .override are called override files.  If an over‐
	   ride file is present, the stanzas it contains take precedence  over
	   those equivalently named stanzas in the corresponding configuration
	   file contents for a particular job.	 The  main  use	 for  override
	   files  is to modify how a job will run without having to modify its
	   configuration file directly.	 See the section  Override  File  Han‐
	   dling below for further details.

       A job can thus be defined by either:

       · A single configuration file.

       · A single configuration file and a single override file.

       Unless  explicitly stated otherwise, any reference to a jobs configura‐
       tion can refer both to a configuration file or an override file.

       Each configuration file defines	the  template  for  a  single  service
       (long-running process or daemon) or task (short-lived process).

       Note that a configuration file is not itself a job: it is a description
       of an environmenta job could be run in.	A job is the  runtime  embodi‐
       ment of a configuration file.

       The  configuration  file	 name  as  displayed by Upstart and associated
       tooling is taken from its relative path within  the  directory  without
       the   extension.	   For	example	 a  configuration  file	 /etc/init/rc-
       sysinit.conf  is	 named	rc-sysinit,   while   a	  configuration	  file
       /etc/init/net/apache.conf  is  named  net/apache.  Since override files
       only modify the way a configuration file is interpreted, they  are  not
       named.

       Configuration files are plain text and should not be executable.

   Configuration File Format
       Each line begins with a configuration stanza and continues until either
       the end of the line or a line containing a closing stanza.  Line breaks
       within  a  stanza  are  permitted within single or double quotes, or if
       preceeded by a blackslash.

       If a stanza is duplicated, the last occurence will  be  used.  Unrecog‐
       nized  stanzas  will  generate parse errors, which will stop a job from
       running.

       Stanzas and their arguments are delimited by whitespace, which consists
       of  one	or  more  space	 or tab characters which are otherwise ignored
       unless placed within single or double quotes.

       Comments begin with a `#' and continue  until  the  end	of  the	 line.
       Blank  lines  and  lines	 consisting only of whitespace or comments are
       ignored.

   Process definition
       The primary use of jobs is to define services or tasks to be run by the
       init(8)	daemon.	 Each job may have one or more different processes run
       as part of its lifecycle, with  the  most  common  known	 as  the  main
       process.

       The  main  process  is defined using either the exec or script stanzas,
       only one of which is permitted.	These specify the executable or	 shell
       script that will be run when the job is considered to be running.  Once
       this process terminates, the job stop.

       All processes are run with the full job environment available as	 envi‐
       ronment variables in their process.

       exec COMMAND [ ARG ]...
	      This stanza defines the process to be run as the name of an exe‐
	      cutable on the filesystem, and zero  or  more  arguments	to  be
	      passed to it.  Any special characters, e.g. quotes or `$' speci‐
	      fied will result in the entire command being passed to  a	 shell
	      for expansion.

	      exec /usr/sbin/acpid -c $EVENTSDIR -s $SOCKET

       script ... end script
	      This stanza defines the process to be run as a shell script that
	      will be executed using sh(1).  The -e  shell  option  is	always
	      used, so any command that fails will terminate the script.

	      The  script  stanza  appears on its own on a line, the script is
	      everything up until the first end script stanza appearing on its
	      own on a line.

	      script
		  dd bs=1 if=/proc/kmsg of=$KMSGSINK
		  exec /sbin/klogd -P $KMSGSINK
	      end script

       There an additional four processes that may be run as part of the job's
       lifecycle.  These are specified as the process  name,  followed	by  an
       exec or script stanza.

       pre-start exec|script...
	      This  process  will be run after the job's starting(7) event has
	      finished, but before the main process is run.  It	 is  typically
	      used to prepare the environment, such as making necessary direc‐
	      tories.

       post-start exec|script...
	      This process will be run before the job's	 started(7)  event  is
	      emitted,	but  after  the	 main process has been spawned.	 It is
	      typically used to send necessary commands to the	main  process,
	      or to delay the started(7) event until the main process is ready
	      to receive clients.

       pre-stop exec|script...
	      This process is run if the job is stopped by an event listed  in
	      its  stop	 on  stanza or by the stop(8) command.	It will be run
	      before the job's stopping(7) event is  emitted  and  before  the
	      main process is killed.  It is typically used to send any neces‐
	      sary shutdown commands to the main process, and it may also call
	      the start(8) command without arguments to cancel the stop.

       post-stop exec|script...
	      This  process  is run after the main process has been killed and
	      before the job's stopped(7) event is emitted.  It	 is  typically
	      used  to	clean  up  the environment, such as removing temporary
	      directories.

       All of these process, including the main process, are  optional.	  Ser‐
       vices  without  a main process will appear to be running until they are
       stopped, this is commonly used to  define  states  such	as  runlevels.
       It's  quite  permissable to have no main process, but to have pre-start
       and post-stop processes for the state.

	      pre-start exec ifup -a
	      post-stop exec ifdown -a

   Event definition
       Jobs can be manually started and stopped at any time by a system admin‐
       strator	using the.  start(8) and stop(8) tools, however it is far more
       useful for jobs to be started and stopped automatically by the  init(8)
       daemon when necessary.

       This  is	 done  by  specifying which events should cause your job to be
       started, and which cause your process to be stopped again.

       The set of possible events is limitless, however there are a number  of
       standard events defined by the init(8) daemon and telinit(8) tools that
       you will want to use.

       When first started, the init(8) daemon will emit the startup(7)	event.
       This  will  activate jobs that implement System V compatibility and the
       runlevel(7) event.  As jobs are started and stopped, the init(8) daemon
       will  emit  the	starting(7),  started(7),  stopping(7)	and stopped(7)
       events on their behalf.

       start on EVENT [[KEY=]VALUE]... [and|or...]
	      The start on stanza defines the set of events  that  will	 cause
	      the job to be automatically started.  Each EVENT is given by its
	      name.  Multiple events are permitted using the and &  or	opera‐
	      tors,  and complex expressions may be performed with parentheses
	      (within which line breaks are permitted).

	      You may also match on the environment variables contained within
	      the event by specifying the KEY and expected VALUE.  If you know
	      the order in which the variables are given to the event you  may
	      omit the KEY.

	      VALUE  may  contain  wildcard  matches and globs as permitted by
	      fnmatch(3) and may expand the value of any variable defined with
	      the env stanza.

	      Negation is permitted by using != between the KEY and VALUE.

	      start on started gdm or started kdm

	      start on device-added SUBSYSTEM=tty DEVPATH=ttyS*

	      start on net-device-added INTERFACE!=lo

       stop on EVENT [[KEY=]VALUE]... [and|or...]
	      The stop on stanza defines the set of events that will cause the
	      job to be automatically stopped.	It  has	 the  same  syntax  as
	      start on.

	      VALUE  may  additionally	expand	the value of any variable that
	      came from the job's start environment (either the event  or  the
	      command that started it).

	      stop on stopping gdm or stopping kdm

	      stop on device-removed DEVPATH=$DEVPATH

   Job environment
       Each  job  is run with the environment from the events or commands that
       started it.  In addition, you may define defaults in the job which  may
       be  overridden  later  and  specify  which  environment	variables  are
       exported into the events generated for the job.

       The special UPSTART_EVENTS environment variable contains	 the  list  of
       events  that  started  the  job,	 it will not be present if the job was
       started manually.

       In addition, the pre-stop and post-stop scripts are run with the	 envi‐
       ronment	 of  the  events  or  commands	that  stopped  the  job.   THe
       UPSTART_STOP_EVENTS environment variable contains the  list  of	events
       that  stopped  the  job,	 it will not be present if the job was stopped
       manually.

       All jobs also contain the UPSTART_JOB and UPSTART_INSTANCE  environment
       variables,  containing  the  name  of  the job and instance.  These are
       mostly used by the initctl(8) utility to default to acting on  the  job
       the commands are called from.

       env KEY=VALUE
	      Defines  a  default environment variable, the value of which may
	      be overriden by the event or command that starts the job.

       export KEY
	      Exports the value of an environment  variable  into  the	start‐
	      ing(7),  started(7),  stopping(7) and stopped(7) events for this
	      job.

   Services, tasks and respawning
       Jobs are services by default.  This means that the act of starting  the
       job is considered to be finished when the job is running, and that even
       exiting with a zero exit status means the service will be respawned.

       task   This stanza may be used to  specify  that	 the  job  is  a  task
	      instead.	 This  means  that  the act of starting the job is not
	      considered to be finished until the job itself has been run  and
	      stopped  again,  but that existing with a zero exit status means
	      the task has completed successfully and will not be respawned.

       The start(8) command, and any starting(7) or  stopping(7)  events  will
       block only until a service is running or until a task has finished.

       respawn
	      A service or task with this stanza will be automatically started
	      if it should stop abnormally.  All reasons for a	service	 stop‐
	      ping,  except  the stop(8) command itself, are considered abnor‐
	      mal.  Tasks may exit with a zero exit status  to	prevent	 being
	      respawned.

       respawn limit COUNT INTERVAL
	      Respawning  is  subject to a limit, if the job is respawned more
	      than COUNT times in INTERVAL seconds, it will be	considered  to
	      be  having deeper problems and will be stopped. Default COUNT is
	      10. Default INTERVAL is 5 seconds.

	      This only applies to automatic respawns and not  the  restart(8)
	      command.

       normal exit STATUS|SIGNAL...
	      Additional  exit	statuses  or even signals may be added, if the
	      job process terminates with any of these it will not be  consid‐
	      ered to have failed and will not be respawned.

	      normal exit 0 1 TERM HUP

   Instances
       By  default,  only one instance of any job is permitted to exist at one
       time.  Attempting to start a job when it's already starting or  running
       results in an error. Note that a job is considered to be running if its
       pre-start process is running.

       Multiple instances may be permitted by  defining	 the  names  of	 those
       instances.   If	an instance with the same name is not already starting
       or running, a new instance will be  started  instead  of	 returning  an
       error.

       instance NAME
	      This  stanza  defines the names of instances, on its own its not
	      particularly useful since it would just define the name  of  the
	      single  permitted	 instance,  however  NAME expands any variable
	      defined in the job's environment.

	      These will often be variables that  you  need  to	 pass  to  the
	      process anyway, so are an excellent way to limit the instances.

	      instance $CONFFILE
	      exec /sbin/httpd -c $CONFFILE

	      instance $TTY
	      exec /sbin/getty -8 38300 $TTY

	      These  jobs  appear  in  the initctl(8) output with the instance
	      name in parentheses, and have the INSTANCE environment  variable
	      set in their events.

   Documentation
       Upstart	provides several stanzas useful for documentation and external
       tools.

       description DESCRIPTION
	      This stanza may contain a description of the job.

	      description "This does neat stuff"

       author AUTHOR
	      This stanza may contain the author of the job, often used	 as  a
	      contact for bug reports.

	      author "Scott James Remnant <scott@netsplit.com>"

       version VERSION
	      This  stanza may contain version information about the job, such
	      as revision control or package version number.  It is  not  used
	      or interpreted by init(8) in any way.

	      version "$Id$"

       emits EVENT...
	      All processes on the system are free to emit their own events by
	      using the initctl(8) tool, or by communicating directly with the
	      init(8) daemon.

	      This  stanza  allows  a job to document in its job configuration
	      what events it emits itself, and may be useful for graphing pos‐
	      sible transitions.

       usage USAGE
	      This  stanza  may contain the text used by initctl(8) usage com‐
	      mand. This text  may  be	also  shown  when  commands  start(8),
	      stop(8) or status(8) fail.

	      usage "tty DEV=ttyX - where X is console id"

   Process environment
       Many  common  adjustments  to the process environment, such as resource
       limits, may be configured directly in the job  rather  than  having  to
       handle them yourself.

       console output|owner
	      By default the standard input, output and error file descriptors
	      of jobs are connected to /dev/null

	      If this stanza is specified, they are connected to  /dev/console
	      instead.

	      console  owner  is  special, it not only connects the job to the
	      system console but sets the job to be the owner  of  the	system
	      console,	which  means  it will receive certain signals from the
	      kernel when special  key	combinations  such  as	Control-C  are
	      pressed.

       umask UMASK
	      A common configuration is to set the file mode creation mask for
	      the process.  UMASK should be an octal value for the  mask,  see
	      umask(2) for more details.

       nice NICE
	      Another  common  configuration  is  to adjust the process's nice
	      value, see nice(1) for more details.

       oom ADJUSTMENT|never
	      Normally the OOM killer  regards	all  processes	equally,  this
	      stanza advises the kernel to treat this job differently.

	      ADJUSTMENT may be an integer value from -16 (very unlikely to be
	      killed by the OOM killer) up to 14 (very likely to be killed  by
	      the OOM killer).	It may also be the special value never to have
	      the job ignored by the OOM killer entirely.

       chroot DIR
	      Runs the job's processes in a chroot(8)  environment  underneath
	      DIR

	      Note  that  DIR must have all the necessary system libraries for
	      the process to be run, often including /bin/sh

       chdir DIR
	      Runs the job's processes with a working directory of DIR instead
	      of the root of the filesystem.

       limit LIMIT SOFT|unlimited HARD|unlimited
	      Sets  initial  system  resource  limits for the job's processes.
	      LIMIT may be one of core, cpu, data, fsize,  memlock,  msgqueue,
	      nice, nofile, nproc, rss, rtprio, sigpending or stack.

	      Limits are specified as both a SOFT value and a HARD value, both
	      of which are integers.  The special value unlimited may be spec‐
	      ified for either.

   Override File Handling
       Override files allow a jobs environment to be changed without modifying
       the jobs configuration file. Rules governing override files:

       · If a job is embodied with only a configuration file, the contents  of
	 this file define the job.

       · If  an	 override files exists where there is no existing cofiguration
	 file, the override file is ignored.

       · If both a configuration file and an override file exist for a job and
	 both files are syntactically correct:

	 · stanzas  in	the  override  file  will take precedence over stanzas
	   present in the corresponding configuration file.

	 · stanzas in the override file which are not present  in  the	corre‐
	   sponding configuration file will be honoured when the job runs.

       · If both a configuration file and an override file exist for a job and
	 subsequently the override file is deleted, the configuration file  is
	 automatically reloaded with the effect that any changes introduced by
	 the override file are undone and the  configuration  file  alone  now
	 defines the job.

       · If both a configuration file and an override file exist for a job and
	 subsequently the configuration file is deleted, a new instance of the
	 job  can no longer be started (since without a corresponding configu‐
	 ration file an override file is ignored).

       · If both a configuration file and an override file exist for a job and
	 any  of  the  contents of the override file are invalid, the override
	 file is ignored and only the contents of the configuration  file  are
	 considered.

   Miscellaneous
       kill timeout INTERVAL
	      Specifies	 the  interval	between sending the job's main process
	      the SIGTERM and SIGKILL signals when stopping the	 running  job.
	      Default is 5 seconds.

       expect stop
	      Specifies	 that  the  job's  main process will raise the SIGSTOP
	      signal to indicate that it is ready.  init(8) will wait for this
	      signal  before running the job's post-start script, or consider‐
	      ing the job to be running.

	      init(8) will send the process the SIGCONT signal to allow it  to
	      continue.

       expect daemon
	      Specifies that the job's main process is a daemon, and will fork
	      twice after being run.  init(8) will follow this	daemonisation,
	      and  will	 wait for this to occur before running the job's post-
	      start script or considering the job to be running.

	      Without this stanza init(8) is unable to supervise  daemon  pro‐
	      cesses  and  will	 believe  them to have stopped as soon as they
	      daemonise on startup.

       expect fork
	      Specifies that the job's main process will fork once after being
	      run.   init(8)  will follow this fork, and will wait for this to
	      occur before running the job's post-start script or  considering
	      the job to be running.

	      Without  this stanza init(8) is unable to supervise forking pro‐
	      cesses and will believe them to have stopped  as	soon  as  they
	      fork on startup.

BUGS
       The  and and or operators allowed with start on and stop on do not work
       intuitively: operands to the right of either operator are  only	evalu‐
       ated  once  and	state  information is then discarded. This can lead to
       jobs with complex start on  or  stop  on	 conditions  not  behaving  as
       expected	 when  restarted.  For example, if a job encodes the following
       condition:

	   start on A and (B or C)

       When 'A' and 'B' become true, the condition is  satisfied  so  the  job
       will  be	 run.  However,	 if  the job ends and subsequently 'A' and 'C'
       become true, the job will not be re-run even  though  the  condtion  is
       satisfied.   Avoid  using complex conditions with jobs which need to be
       restarted.

AUTHOR
       Manual page written by Scott  James  Remnant  <scott@netsplit.com>  and
       James Hunt <james.hunt@canonical.com>.

REPORTING BUGS
       Report bugs at <https://launchpad.net/upstart/+bugs>

COPYRIGHT
       Copyright © 2010 Canonical Ltd.
       This is free software; see the source for copying conditions.  There is
       NO warranty; not even for MERCHANTABILITY or FITNESS FOR	 A  PARTICULAR
       PURPOSE.

SEE ALSO
       init(8) sh(1)

Upstart				  2011-01-12			       init(5)
[top]

List of man pages available for Scientific

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net