getpriority man page on RedHat

Man page or keyword search:  
man Server   29550 pages
apropos Keyword Search (all sections)
Output format
RedHat logo
[printable version]

GETPRIORITY(2)		   Linux Programmer's Manual		GETPRIORITY(2)

NAME
       getpriority, setpriority - get/set program scheduling priority

SYNOPSIS
       #include <sys/time.h>
       #include <sys/resource.h>

       int getpriority(int which, int who);
       int setpriority(int which, int who, int prio);

DESCRIPTION
       The  scheduling	priority  of  the  process, process group, or user, as
       indicated by which and who is obtained with the getpriority() call  and
       set with the setpriority() call.

       The  value  which  is one of PRIO_PROCESS, PRIO_PGRP, or PRIO_USER, and
       who  is	interpreted  relative  to  which  (a  process  identifier  for
       PRIO_PROCESS, process group identifier for PRIO_PGRP, and a user ID for
       PRIO_USER).  A zero value for who denotes  (respectively)  the  calling
       process,	 the process group of the calling process, or the real user ID
       of the calling process.	Prio is a value in the range -20  to  19  (but
       see  the	 Notes	below).	  The  default priority is 0; lower priorities
       cause more favorable scheduling.

       The getpriority() call returns the highest priority  (lowest  numerical
       value)  enjoyed	by  any of the specified processes.  The setpriority()
       call sets the priorities of all of the specified processes to the spec‐
       ified value.  Only the superuser may lower priorities.

RETURN VALUE
       Since  getpriority() can legitimately return the value -1, it is neces‐
       sary to clear the external variable errno prior to the call, then check
       it afterward to determine if -1 is an error or a legitimate value.  The
       setpriority() call returns 0 if there is no error, or -1 if there is.

ERRORS
       EINVAL which was not one of PRIO_PROCESS, PRIO_PGRP, or PRIO_USER.

       ESRCH  No process was located using the which and who values specified.

       In addition to the errors indicated above, setpriority() may fail if:

       EACCES The caller attempted to lower a process priority,	 but  did  not
	      have  the	 required  privilege  (on  Linux:  did	not  have  the
	      CAP_SYS_NICE capability).	 Since Linux 2.6.12, this error occurs
	      only  if	the  caller attempts to set a process priority outside
	      the range of the RLIMIT_NICE soft resource limit of  the	target
	      process; see getrlimit(2) for details.

       EPERM  A	 process  was located, but its effective user ID did not match
	      either the effective or the real user ID of the caller, and  was
	      not privileged (on Linux: did not have the CAP_SYS_NICE capabil‐
	      ity).  But see NOTES below.

CONFORMING TO
       SVr4,  4.4BSD  (these  function	calls  first  appeared	 in   4.2BSD),
       POSIX.1-2001.

NOTES
       A  child created by fork(2) inherits its parent's nice value.  The nice
       value is preserved across execve(2).

       The degree to which their relative nice value affects the scheduling of
       processes varies across UNIX systems, and, on Linux, across kernel ver‐
       sions.  Starting with kernel 2.6.23, Linux adopted  an  algorithm  that
       causes  relative	 differences  in  nice	values to have a much stronger
       effect.	This causes very low nice values (+19) to truly provide little
       CPU  to	a  process whenever there is any other higher priority load on
       the system, and makes high nice values (-20) deliver most of the CPU to
       applications that require it (e.g., some audio applications).

       The details on the condition for EPERM depend on the system.  The above
       description is what POSIX.1-2001 says, and seems to be followed on  all
       System  V-like  systems.	 Linux kernels before 2.6.12 required the real
       or effective user ID of the caller  to  match  the  real	 user  of  the
       process who (instead of its effective user ID).	Linux 2.6.12 and later
       require the effective user ID of the caller to match the real or effec‐
       tive  user  ID  of the process who.  All BSD-like systems (SunOS 4.1.3,
       Ultrix 4.2, 4.3BSD, FreeBSD 4.3, OpenBSD-2.5, ...) behave in  the  same
       manner as Linux 2.6.12 and later.

       The actual priority range varies between kernel versions.  Linux before
       1.3.36 had -infinity..15.  Since kernel 1.3.43,	Linux  has  the	 range
       -20..19.	 Within the kernel, nice values are actually represented using
       the corresponding range 40..1 (since negative numbers are error	codes)
       and  these  are	the values employed by the setpriority() and getprior‐
       ity() system calls.  The glibc wrapper functions for these system calls
       handle  the  translations  between the user-land and kernel representa‐
       tions of the nice value according to the formula unice = 20 - knice.

       On some systems, the range of nice values is -20..20.

       Including <sys/time.h> is not required these days, but increases porta‐
       bility.	 (Indeed,  <sys/resource.h>  defines the rusage structure with
       fields of type struct timeval defined in <sys/time.h>.)

BUGS
       According to POSIX, the nice value is a per-process setting.   However,
       under  the current Linux/NPTL implementation of POSIX threads, the nice
       value is a per-thread attribute: different threads in the same  process
       can  have  different  nice  values.  Portable applications should avoid
       relying on the Linux behavior, which may be made	 standards  conformant
       in the future.

SEE ALSO
       nice(1), renice(1), fork(2), capabilities(7)

       Documentation/scheduler/sched-nice-design.txt   in   the	 Linux	kernel
       source tree (since Linux 2.6.23)

COLOPHON
       This page is part of release 3.53 of the Linux  man-pages  project.   A
       description  of	the project, and information about reporting bugs, can
       be found at http://www.kernel.org/doc/man-pages/.

Linux				  2013-02-12			GETPRIORITY(2)
[top]

List of man pages available for RedHat

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net