FPUTWC(3P) POSIX Programmer's Manual FPUTWC(3P)PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux
implementation of this interface may differ (consult the corresponding
Linux manual page for details of Linux behavior), or the interface may
not be implemented on Linux.
NAMEfputwc — put a wide-character code on a stream
wint_t fputwc(wchar_t wc, FILE *stream);
The functionality described on this reference page is aligned with the
ISO C standard. Any conflict between the requirements described here
and the ISO C standard is unintentional. This volume of POSIX.1‐2008
defers to the ISO C standard.
The fputwc() function shall write the character corresponding to the
wide-character code wc to the output stream pointed to by stream, at
the position indicated by the associated file-position indicator for
the stream (if defined), and advances the indicator appropriately. If
the file cannot support positioning requests, or if the stream was
opened with append mode, the character is appended to the output
stream. If an error occurs while writing the character, the shift state
of the output file is left in an undefined state.
The last data modification and last file status change timestamps of
the file shall be marked for update between the successful execution of
fputwc() and the next successful completion of a call to fflush() or
fclose() on the same stream or a call to exit() or abort().
The fputwc() function shall not change the setting of errno if success‐
Upon successful completion, fputwc() shall return wc. Otherwise, it
shall return WEOF, the error indicator for the stream shall be set, and
errno shall be set to indicate the error.
The fputwc() function shall fail if either the stream is unbuffered or
data in the stream's buffer needs to be written, and:
EAGAIN The O_NONBLOCK flag is set for the file descriptor underlying
stream and the thread would be delayed in the write operation.
EBADF The file descriptor underlying stream is not a valid file
descriptor open for writing.
EFBIG An attempt was made to write to a file that exceeds the maximum
file size or the file size limit of the process.
EFBIG The file is a regular file and an attempt was made to write at
or beyond the offset maximum associated with the corresponding
EILSEQ The wide-character code wc does not correspond to a valid char‐
EINTR The write operation was terminated due to the receipt of a sig‐
nal, and no data was transferred.
EIO A physical I/O error has occurred, or the process is a member of
a background process group attempting to write to its control‐
ling terminal, TOSTOP is set, the calling thread is not blocking
SIGTTOU, the process is not ignoring SIGTTOU, and the process
group of the process is orphaned. This error may also be
returned under implementation-defined conditions.
ENOSPC There was no free space remaining on the device containing the
EPIPE An attempt is made to write to a pipe or FIFO that is not open
for reading by any process. A SIGPIPE signal shall also be sent
to the thread.
The fputwc() function may fail if:
ENOMEM Insufficient storage space is available.
ENXIO A request was made of a nonexistent device, or the request was
outside the capabilities of the device.
The following sections are informative.
Section 2.5, Standard I/O Streams, ferror(), fopen(), setbuf(),
The Base Definitions volume of POSIX.1‐2008, <stdio.h>, <wchar.h>
Portions of this text are reprinted and reproduced in electronic form
from IEEE Std 1003.1, 2013 Edition, Standard for Information Technology
-- Portable Operating System Interface (POSIX), The Open Group Base
Specifications Issue 7, Copyright (C) 2013 by the Institute of Electri‐
cal and Electronics Engineers, Inc and The Open Group. (This is
POSIX.1-2008 with the 2013 Technical Corrigendum 1 applied.) In the
event of any discrepancy between this version and the original IEEE and
The Open Group Standard, the original IEEE and The Open Group Standard
is the referee document. The original Standard can be obtained online
at http://www.unix.org/online.html .
Any typographical or formatting errors that appear in this page are
most likely to have been introduced during the conversion of the source
files to man page format. To report such errors, see https://www.ker‐
IEEE/The Open Group 2013 FPUTWC(3P)