FPING(8)FPING(8)NAMEfping - send ICMP ECHO_REQUEST packets to network hosts
SYNOPSISfping [ options ] [ systems... ]
DESCRIPTIONfping is a program like ping which uses the Internet Control Message
Protocol (ICMP) echo request to determine if a target host is
responding. fping differs from ping in that you can specify any number
of targets on the command line, or specify a file containing the lists
of targets to ping. Instead of sending to one target until it times
out or replies, fping will send out a ping packet and move on to the
next target in a round-robin fashion. In the default mode, if a target
replies, it is noted and removed from the list of targets to check; if
a target does not respond within a certain time limit and/or retry
limit it is designated as unreachable. fping also supports sending a
specified number of pings to a target, or looping indefinitely (as in
ping ). Unlike ping, fping is meant to be used in scripts, so its
output is designed to be easy to parse.
OPTIONS-4, --ipv4
Restrict name resolution and IPs to IPv4 addresses.
-6, --ipv6
Restrict name resolution and IPs to IPv6 addresses.
-a, --alive
Show systems that are alive.
-A, --addr
Display targets by address rather than DNS name. Combined with -d,
the output will be both the ip and (if available) the hostname.
-b, --size=BYTES
Number of bytes of ping data to send. The minimum size (normally
12) allows room for the data that fping needs to do its work
(sequence number, timestamp). The reported received data size
includes the IP header (normally 20 bytes) and ICMP header (8
bytes), so the minimum total size is 40 bytes. Default is 56, as
in ping. Maximum is the theoretical maximum IP datagram size
(64K), though most systems limit this to a smaller, system-
dependent number.
-B, --backoff=N
Backoff factor. In the default mode, fping sends several requests
to a target before giving up, waiting longer for a reply on each
successive request. This parameter is the value by which the wait
time (-t) is multiplied on each successive request; it must be
entered as a floating-point number (x.y). The default is 1.5.
-c, --count=N
Number of request packets to send to each target. In this mode, a
line is displayed for each received response (this can suppressed
with -q or -Q). Also, statistics about responses for each target
are displayed when all requests have been sent (or when
interrupted).
-C, --vcount=N
Similar to -c, but the per-target statistics are displayed in a
format designed for automated response-time statistics gathering.
For example:
$ fping-C 5 -q somehost
somehost : 91.7 37.0 29.2 - 36.8
shows the response time in milliseconds for each of the five
requests, with the "-" indicating that no response was received to
the fourth request.
-d, --rdns
Use DNS to lookup address of return ping packet. This allows you
to give fping a list of IP addresses as input and print hostnames
in the output. This is similar to option -n/--name, but will force
a reverse-DNS lookup even if you give hostnames as target
(NAME->IP->NAME).
-D, --timestamp
Add Unix timestamps in front of output lines generated with in
looping or counting modes (-l, -c, or -C).
-e, --elapsed
Show elapsed (round-trip) time of packets.
-f, --file
Read list of targets from a file. This option can only be used by
the root user. Regular users should pipe in the file via stdin:
$ fping < targets_file
-g, --generate addr/mask
Generate a target list from a supplied IP netmask, or a starting
and ending IP. Specify the netmask or start/end in the targets
portion of the command line. If a network with netmask is given,
the network and broadcast addresses will be excluded. ex. To ping
the network 192.168.1.0/24, the specified command line could look
like either:
$ fping-g 192.168.1.0/24
or
$ fping-g 192.168.1.1 192.168.1.254
-h, --help
Print usage message.
-H, --ttl=N
Set the IP TTL field (time to live hops).
-i, --interval=MSEC
The minimum amount of time (in milliseconds) between sending a
ping packet to any target (default is 10, minimum is 1).
-I, --iface=IFACE
Set the interface (requires SO_BINDTODEVICE support).
-l, --loop
Loop sending packets to each target indefinitely. Can be
interrupted with Ctrl-C; statistics about responses for each
target are then displayed.
-m, --all
Send pings to each of a target host's multiple IP addresses (use
of option '-A' is recommended).
-M, --dontfrag
Set the "Don't Fragment" bit in the IP header (used to
determine/test the MTU).
-n, --name
If targets are specified as IP addresses, do a reverse-DNS lookup
on them to
-N, --netdata
Format output for netdata (-l -Q are required). See:
<http://my-netdata.io/>
-o, --outage
Calculate "outage time" based on the number of lost pings and the
interval used (useful for network convergence tests).
-O, --tos=N
Set the typ of service flag (TOS). N can be either decimal or
hexadecimal (0xh) format.
-p, --period=MSEC
In looping or counting modes (-l, -c, or -C), this parameter sets
the time in milliseconds that fping waits between successive
packets to an individual target. Default is 1000 and minimum is
10.
-q, --quet
Quiet. Don't show per-probe results, but only the final summary.
Also don't show ICMP error messages.
-Q, --squiet=SECS
Like -q, but show summary results every n seconds.
-r, --retry=N
Retry limit (default 3). This is the number of times an attempt at
pinging a target will be made, not including the first try.
-R, --random
Instead of using all-zeros as the packet data, generate random
bytes. Use to defeat, e.g., link data compression.
-s, --src
Print cumulative statistics upon exit.
-S, --src=addr
Set source address.
-t, --timeout=MSEC
Initial target timeout in milliseconds. In the default, non-loop
mode, the default timeout is 500ms, and it represents the amount
of time that fping waits for a response to its first request.
Successive timeouts are multiplied by the backoff factor specified
with -B.
In loop/count mode, the default timeout is automatically adjusted
to match the "period" value (but not more than 2000ms). You can
still adjust the timeout value with this option, if you wish to,
but note that setting a value larger than "period" produces
inconsistent results, because the timeout value can be respected
only for the last ping.
Also note that any received replies that are larger than the
timeout value, will be discarded.
-T n Ignored (for compatibility with fping 2.4).
-u, --unreach
Show targets that are unreachable.
-v, --version
Print fping version information.
EXAMPLES
Generate 20 pings to two hosts in ca. 1 second (i.e. one ping every 50
ms to each host), and report every ping RTT at the end:
$ fping--quiet --interval=1 --vcount=20 --period=50 127.0.0.1 127.0.0.2
AUTHORS
· Roland J. Schemers III, Stanford University, concept and versions
1.x
· RL "Bob" Morgan, Stanford University, versions 2.x
· David Papp, versions 2.3x and up
· David Schweikert, versions 3.0 and up
fping website: <http://www.fping.org>
DIAGNOSTICS
Exit status is 0 if all the hosts are reachable, 1 if some hosts were
unreachable, 2 if any IP addresses were not found, 3 for invalid
command line arguments, and 4 for a system call failure.
RESTRICTIONS
If fping was configured with "--enable-safe-limits", the following
values are not allowed for non-root users:
· -i n, where n < 1 msec
· -p n, where n < 10 msec
SEE ALSOping(8)fping 2017-04-23 FPING(8)
