buf(9S) Data Structures for Drivers buf(9S)NAMEbuf - block I/O data transfer structure
SYNOPSIS
#include <sys/ddi.h>
#include <sys/sunddi.h>
INTERFACE LEVEL
Architecture independent level 1 (DDI/DKI)
DESCRIPTION
The buf structure is the basic data structure for block I/O transfers.
Each block I/O transfer has an associated buffer header. The header
contains all the buffer control and status information. For drivers,
the buffer header pointer is the sole argument to a block driver strat‐
egy(9E) routine. Do not depend on the size of the buf structure when
writing a driver.
A buffer header can be linked in multiple lists simultaneously. Because
of this, most of the members in the buffer header cannot be changed by
the driver, even when the buffer header is in one of the driver's work
lists.
Buffer headers are also used by the system for unbuffered or physical
I/O for block drivers. In this case, the buffer describes a portion of
user data space that is locked into memory.
Block drivers often chain block requests so that overall throughput for
the device is maximized. The av_forw and the av_back members of the buf
structure can serve as link pointers for chaining block requests.
STRUCTURE MEMBERS
int b_flags; /* Buffer status */
struct buf *av_forw; /* Driver work list link */
struct buf *av_back; /* Driver work list link */
size_t b_bcount; /* # of bytes to transfer */
union {
caddr_t b_addr; /* Buffer's virtual address */
} b_un;
daddr_t b_blkno; /* Block number on device */
diskaddr_t b_lblkno; /* Expanded block number on device */
size_t b_resid; /* # of bytes not transferred */
size_t b_bufsize; /* size of allocated buffer */
int (*b_iodone)(struct buf *); /* function called */
/* by biodone */
int b_error; /* expanded error field */
void *b_private; /* "opaque" driver private area */
dev_t b_edev; /* expanded dev field */
The members of the buffer header available to test or set by a driver
are as follows:
b_flags stores the buffer status and indicates to the driver whether to
read or write to the device. The driver must never clear the b_flags
member. If this is done, unpredictable results can occur including loss
of disk sanity and the possible failure of other kernel processes.
All b_flags bit values not otherwise specified above are reserved by
the kernel and may not be used.
Valid flags are as follows:
B_BUSY Indicates the buffer is in use. The driver must not
change this flag unless it allocated the buffer with
getrbuf(9F) and no I/O operation is in progress.
B_DONE Indicates the data transfer has completed. This flag is
read-only.
B_ERROR Indicates an I/O transfer error. It is set in conjunc‐
tion with the b_error field. bioerror(9F) should be
used in preference to setting the B_ERROR bit.
B_PAGEIO Indicates the buffer is being used in a paged I/O
request. See the description of the b_un.b_addr field
for more information. This flag is read-only.
B_PHYS indicates the buffer header is being used for physical
(direct) I/O to a user data area. See the description
of the b_un.b_addr field for more information. This
flag is read-only.
B_READ Indicates that data is to be read from the peripheral
device into main memory.
B_WRITE Indicates that the data is to be transferred from main
memory to the peripheral device. B_WRITE is a pseudo
flag and cannot be directly tested; it is only detected
as the NOT form of B_READ.
av_forw and av_back can be used by the driver to link the buffer into
driver work lists.
b_bcount specifies the number of bytes to be transferred in both a
paged and a non-paged I/O request.
b_un.b_addr is the virtual address of the I/O request, unless B_PAGEIO
is set. The address is a kernel virtual address, unless B_PHYS is set,
in which case it is a user virtual address. If B_PAGEIO is set,
b_un.b_addr contains kernel private data. Note that either one of
B_PHYS and B_PAGEIO, or neither, can be set, but not both.
b_blkno identifies which logical block on the device (the device is
defined by the device number) is to be accessed. The driver might have
to convert this logical block number to a physical location such as a
cylinder, track, and sector of a disk. This is a 32-bit value. The
driver should use b_blkno or b_lblkno, but not both.
b_lblkno identifies which logical block on the device (the device is
defined by the device number) is to be accessed. The driver might have
to convert this logical block number to a physical location such as a
cylinder, track, and sector of a disk. This is a 64-bit value. The
driver should use b_lblkno or b_blkno, but not both.
b_resid should be set to the number of bytes not transferred because of
an error.
b_bufsize contains the size of the allocated buffer.
b_iodone identifies a specific biodone routine to be called by the
driver when the I/O is complete.
b_error can hold an error code that should be passed as a return code
from the driver. b_error is set in conjunction with the B_ERROR bit set
in the b_flags member. bioerror(9F) should be used in preference to
setting the b_error field.
b_private is for the private use of the device driver.
b_edev contains the major and minor device numbers of the device
accessed.
SEE ALSOstrategy(9E), aphysio(9F), bioclone(9F), biodone(9F), bioerror(9F),
bioinit(9F), clrbuf(9F), getrbuf(9F), physio(9F), iovec(9S), uio(9S)
Writing Device Drivers
WARNINGS
Buffers are a shared resource within the kernel. Drivers should read or
write only the members listed in this section. Drivers that attempt to
use undocumented members of the buf structure risk corrupting data in
the kernel or on the device.
SunOS 5.10 19 Sep 2002 buf(9S)
