CURLOPT_HTTPHEADER(3) curl_easy_setopt options CURLOPT_HTTPHEADER(3)NAMECURLOPT_HTTPHEADER - set custom HTTP headers
SYNOPSIS
#include <curl/curl.h>
CURLcode curl_easy_setopt(CURL *handle, CURLOPT_HTTPHEADER, struct
curl_slist *headers);
DESCRIPTION
Pass a pointer to a linked list of HTTP headers to pass to the server
and/or proxy in your HTTP request. The same list can be used for both
host and proxy requests!
The linked list should be a fully valid list of struct curl_slist
structs properly filled in. Use curl_slist_append(3) to create the list
and curl_slist_free_all(3) to clean up an entire list. If you add a
header that is otherwise generated and used by libcurl internally, your
added one will be used instead. If you add a header with no content as
in 'Accept:' (no data on the right side of the colon), the internally
used header will get disabled. With this option you can add new head‐
ers, replace internal headers and remove internal headers. To add a
header with no content (nothing to the right side of the colon), use
the form 'MyHeader;' (note the ending semicolon).
The headers included in the linked list must not be CRLF-terminated,
because libcurl adds CRLF after each header item. Failure to comply
with this will result in strange bugs because the server will most
likely ignore part of the headers you specified.
The first line in a request (containing the method, usually a GET or
POST) is not a header and cannot be replaced using this option. Only
the lines following the request-line are headers. Adding this method
line in this list of headers will only cause your request to send an
invalid header. Use CURLOPT_CUSTOMREQUEST(3) to change the method.
When this option is passed to curl_easy_setopt(3), libcurl will not
copy the entire list so you must keep it around until you no longer use
this handle for a transfer before you call curl_slist_free_all(3) on
the list.
Pass a NULL to this option to reset back to no custom headers.
The most commonly replaced headers have "shortcuts" in the options CUR‐
LOPT_COOKIE(3), CURLOPT_USERAGENT(3) and CURLOPT_REFERER(3). We recom‐
mend using those.
There's an alternative option that sets or replaces headers only for
requests that are sent with CONNECT to a proxy: CURLOPT_PROXYHEADER(3).
Use CURLOPT_HEADEROPT(3) to control the behavior.
SECURITY CONCERNS
By default, this option makes libcurl send the given headers in all
HTTP requests done by this handle. You should therefore use this option
with caution if you for example connect to the remote site using a
proxy and a CONNECT request, you should to consider if that proxy is
supposed to also get the headers. They may be private or otherwise sen‐
sitive to leak.
Use CURLOPT_HEADEROPT(3) to make the headers only get sent to where you
intend them to get sent.
DEFAULT
NULL
PROTOCOLS
HTTP
EXAMPLE
CURL *curl = curl_easy_init();
struct curl_slist *list = NULL;
if(curl) {
curl_easy_setopt(curl, CURLOPT_URL, "http://example.com");
list = curl_slist_append(list, "Shoesize: 10");
list = curl_slist_append(list, "Accept:");
curl_easy_setopt(curl, CURLOPT_HTTPHEADER, list);
curl_easy_perform(curl);
curl_slist_free_all(list); /* free the list again */
}
AVAILABILITY
As long as HTTP is enabled
RETURN VALUE
Returns CURLE_OK if HTTP is supported, and CURLE_UNKNOWN_OPTION if not.
SEE ALSOCURLOPT_CUSTOMREQUEST(3), CURLOPT_HEADEROPT(3), CURLOPT_PROXYHEADER(3),
CURLOPT_HEADER(3)libcurl 7.37.0 17 Jun 2014 CURLOPT_HTTPHEADER(3)
